Worm variable speed gear motor, Power= 0.18 kW, Speed= 17 - 88 rpm, Voltage= 3 x 230/400 V-50 Hz, 3 x 265/460 V-60 Hz (± 5% according to VDE 0530), Protection type= IP55, Iso class= F (155°C), Operating mode= S1, Duty cycle= S1- 100%, Total length= approx. 415 mm, Hollow shaft= 18 mm, Motor Speed= 4 poles, Translation with adjustment unit (i)= 16 - 82 Gear ratio only worm gear (i)= 10, Torque= 12 Nm - 23 Nm, Service factor (f.s.)= 1, Terminal box= on top (rotatable), Weight= 12 kg, Color= RAL 5010 (gentian blue), Temperature sensor= 3 x PTC thermistor, gearbox housing= aluminium, ball bearing= SKF, C&U or equivalent, Cooling= axial fan (plastic). For technical reasons, the variable speed worm gear motor should cannot be operated with a frequency converter. The drive complies with IEC 60034-30:2008, is suitable for both directions of rotation and contains an oil filling on delivery. Open hollow shafts are marked with to be closed with a cover cap. This can be ordered under the heading "Accessories". According to VDE 0105 and IEC 364, all work on the electric drive may only be carried out by qualified personnel.   As usual with variable speed gears, speed control by turning the handwheel is only permitted during operation! A change in speed while stationary can damage the stepless adjustment unit. All product photos are non-binding examples! Technical changes reserved.

Worm variable speed gear motor, power= 0.18 kW, speed= 22.5 - 117 rpm, Voltage= 3 x 230/400 V-50 Hz, 3 x 265/460 V-60 Hz (± 5% in accordance with VDE 0530), protection class= IP55, Insulation class= F (155°C), operating mode= S1, duty cycle= S1- 100%, total length= approx. 415 mm, Hollow shaft= 18 mm, motor speed= 4 pole, gear ratio with adjustment unit (i)= 12 - 61.5Gear ratio only worm gear (i)= 7.5, torque= 9 Nm - 18 Nm, operating factor (f.s.)= 1. Terminal box = top (rotatable), weight = 12 kg, color = RAL 5010 (gentian blue), Temperature sensor = 3 x PTC thermistors, gear housing = aluminum, ball bearings = SKF, C&U or equivalent, Cooling = axial fan (plastic). The drive complies with IEC 60034-30:2008, is suitable for both directions of rotation and is supplied with an oil filling. Open hollow shafts must be closed with a cover cap. This can be ordered under the "Accessories" section. In accordance with VDE 0105 or. According to IEC 364, all work on the electric drive must only be carried out by qualified specialist personnel. As is usual with variable speed drives, speed control by turning the handwheel is only permitted during operation! A speed change when the drive is at a standstill can lead to damage to the stepless adjustment unit. All product photos are non-binding examples! Technical changes reserved.

Worm variable speed gear motor, Power= 0.18 kW, Speed= 8.5 - 44 rpm, Voltage= 3 x 230/400 V-50 Hz, 3 x 265/460 V-60 Hz (± 5% according to VDE 0530), Protection type= IP55, Iso class= F (155°C), Operating mode= S1, Duty cycle= S1- 100%, Total length= approx. 415 mm, Hollow shaft= 18 mm, Motor Speed= 4 poles, Gear ratio with adjustment unit (i)= 32 - 164 Gear ratio only worm gear (i)= 20, Torque= 22 Nm - 40 Nm, Operating factor ( f.s.)= 1, Terminal box= above (rotatable), Weight= 12 kg, Color= RAL 5010 (gentian blue), Temperature sensor= 3 x PTC Thermistor, Gear housing = aluminum, Ball bearing = SKF, C&U or equivalent, Cooling= axial fan (plastic). For technical reasons, the variable speed worm gear motor should cannot be operated with a frequency converter. The drive corresponds to IEC 60034-30:2008, is suitable for both directions of rotation and is supplied with an oil filling. Open hollow shafts are to be sealed with a cover cap. This can be ordered under the heading "Accessories". According to VDE 0105 and IEC 364, all work on the electric drive may only be carried out by qualified personnel. As usual with variable speed gears, speed control by turning the handwheel is only permitted during operation! A change in speed while stationary can damage the stepless adjustment unit. All product photos are non-binding examples! Technical changes reserved.

Worm variable speed gear motor, power= 0.18 kW, speed= 4.5 - 22 rpm, Voltage= 3 x 230/400 V-50 Hz, 3 x 265/460 V-60 Hz (± 5% in accordance with VDE 0530), Protection class= IP55, insulation class= F (155°C), operating mode= S1, duty cycle= S1- 100%, total length= approx. 415 mm, Hollow shaft= 18 mm, motor speed= 4 pole, gear ratio with adjustment unit (i)= 46 - 328, Gear ratio only worm gear (i)= 40, torque= 37 Nm – 62 Nm, operating factor (f.s.)= 1, Terminal box = top (rotatable), weight = 12 kg, color = RAL 5010 (gentian blue), Temperature sensor = 3 x PTC thermistors, gear housing = aluminum, ball bearings = SKF, C&U or equivalent, Cooling = axial fan (plastic). The drive complies with IEC 60034-30:2008, is suitable for both directions of rotation and is supplied with an oil filling. Open hollow shafts must be closed with a cover cap. This can be ordered under the "Accessories" section. In accordance with VDE 0105 or. IEC 364, all work on the electric drive must only be carried out by qualified specialist personnel. As is usual with variable speed drives, speed control by turning the handwheel is only permitted during operation! A speed change when the drive is at a standstill can lead to damage to the stepless adjustment unit.   All product photos are non-binding examples! Technical changes reserved.

Worm variable speed gear motor, power= 0.18 kW, Speed= 6 - 29 rpm, Voltage= 3 x 230/400 V-50 Hz, 3 x 265/460 V-60 Hz (± 5% according to VDE 0530), Protection type= IP55, iso class= F (155°C), Operating mode= S1, Duty cycle= S1- 100%, Total length= approx. 415 mm, Hollow shaft = 18 mm, motor speed = 4 poles, translation with adjustment unit (i) = 48 - 246 Transmission only worm gear (i) = 30, torque = 30 Nm - 51 Nm, service factor ( f.s.)= 1, terminal box= above (rotatable), weight= 12 kg, color= RAL 5010 (gentian blue), temperature sensor= 3 x PTC thermistor, gear housing = aluminum, ball bearing = SKF, C&U or equivalent, Cooling=axial fan (plastic). The drive complies with IEC 60034-30:2008, is suitable for both directions of rotation and includes an oil filling upon delivery. Open hollow shafts are included to be closed with a cover cap. This can be ordered under the “Accessories” section. According to VDE 0105 or IEC 364, all work on the electric drive must only be carried out by qualified specialist personnel. As is usual with variable speed gearboxes, speed control by turning the handwheel is only permitted during operation! A change in speed while at a standstill can lead to damage to the continuously variable adjustment unit. All product photos are non-binding examples! Technical changes reserved.

Worm variable speed gear motor, Power= 0.18 kW, Speed= 3.5 - 17.5 rpm, Voltage= 3 x 230/400 V-50 Hz, 3 x 265/460 V-60 Hz (± 5% according to VDE 0530), Protection type= IP55, Iso class= F (155°C), Operating mode= S1, Duty cycle= S1- 100%, Total length= approx. 415 mm, Hollow shaft = 18 mm, Motor speed = 4 poles, Translation with adjustment unit (i) = 80 - 410 Transmission only worm gear (i) = 50, Torque = 43 Nm - 60 Nm, Service factor ( f.s.)= 1, Terminal box= above (rotatable), Weight= 12 kg, Color= RAL 5010 (gentian blue), Temperature sensor= 3 x PTC Thermistor, Gear housing = Aluminum, Ball bearing = SKF, C&U or equivalent, Cooling= axial fan (plastic). For technical reasons, the variable speed worm gear motor should cannot be operated with a frequency converter. The drive corresponds to IEC 60034-30:2008, is suitable for both directions of rotation and is supplied with an oil filling. Open hollow shafts are to be sealed with a cover cap. This can be ordered under the heading "Accessories". According to VDE 0105 and IEC 364, all work on the electric drive may only be carried out by qualified personnel. As usual with variable speed gears, speed control by turning the hand wheel is only permitted during operation! A change in speed while stationary can damage the stepless adjustment unit. All product photos are non-binding examples! Technical changes reserved.

worm variable speed gear motor, Power= 0.18 kW, Speed= 11.5 - 58 rpm, Voltage= 3 x 230/400 V-50 Hz, 3 x 265/460 V-60 Hz (± 5% according to VDE 0530), Protection type= IP55, Iso class= F (155°C), Operating mode= S1, Duty cycle= S1- 100%, Total length= approx. 415 mm, Hollow shaft= 18 mm, Motor Speed= 4 poles, Gear ratio with adjustment unit (i)= 24 - 123Gear ratio only worm gear (i)= 15, Torque= 17 Nm - 32 Nm, Service factor ( f.s.)= 1. Terminal box= above (rotatable), Weight= 12 kg, Color= RAL 5010 (gentian blue), Temperature sensor= 3 x PTC thermistor, Gear housing = aluminum, Ball bearing = SKF, C&U or equivalent, Cooling=axial fan (plastic). The drive complies with IEC 60034-30:2008, is suitable for both directions of rotation and includes an oil filling upon delivery. Open hollow shafts are included to be closed with a cover cap. This can be ordered under the “Accessories” section. According to VDE 0105 or IEC 364, all work on the electric drive must only be carried out by qualified specialist personnel. As is usual with variable speed gearboxes, speed control by turning the handwheel is only permitted during operation! A change in speed while at a standstill can lead to damage to the continuously variable adjustment unit. All product photos are non-binding examples! Technical changes reserved.

Worm variable speed gear motor, Power= 0.18 kW, Speed= 7 - 35 rpm, Voltage= 3 x 230/400 V-50 Hz, 3 x 265/460 V-60 Hz (± 5% according to VDE 0530), Protection type= IP55, iso class= F (155°C), Operating mode= S1, Duty cycle= S1- 100%, Total length= approx. 415 mm, Hollow shaft= 18 mm, motor Speed= 4 poles, gear ratio with adjustment unit (i)= 40 - 205 Gear ratio only worm gear (i)= 25, torque= 27 Nm - 47 Nm, service factor ( f.s.)= 1, terminal box= above (rotatable), weight= 12 kg, color= RAL 5010 (gentian blue), temperature sensor= 3 x PTC thermistor, gear housing = aluminum, ball bearing = SKF, C&U or equivalent, Cooling=axial fan (plastic). The drive complies with IEC 60034-30:2008, is suitable for both directions of rotation and includes an oil filling upon delivery. Open hollow shafts are included to be closed with a cover cap. This can be ordered under the “Accessories” section. According to VDE 0105 or IEC 364, all work on the electric drive must only be carried out by qualified specialist personnel. As is usual with variable speed gearboxes, speed control by turning the handwheel is only permitted during operation! A change in speed while at a standstill can lead to damage to the continuously variable adjustment unit. All product photos are non-binding examples! Technical changes reserved.

Worm variable speed gear motor, Power= 0.18 kW, Speed= 2.5 - 11 rpm, Voltage= 3 x 230/400 V-50 Hz, 3 x 265/460 V-60 Hz (± 5% according to VDE 0530), Protection type= IP55, iso class= F (155°C), Operating mode= S1, Duty cycle= S1- 100%, Total length= approx. 459 mm, Hollow shaft= 25 mm, Motor Speed= 4 poles, Gear ratio with adjustment unit (i)= 128 - 656 Gear ratio only worm gear (i)= 80, Torque= 59 Nm – 82 Nm, Service factor ( f.s.)= 1, Terminal box= above (rotatable), Weight= 13 kg, Color= RAL 5010 (gentian blue), Temperature sensor= 3 x PTC thermistors, Gear housing = aluminum, Ball bearing = SKF, C&U or equivalent, Cooling= axial fan (plastic). For technical reasons, the variable speed worm gear motor should cannot be operated with a frequency converter. The drive corresponds to IEC 60034-30:2008, is suitable for both directions of rotation and is supplied with an oil filling. Open hollow shafts are to be sealed with a cover cap. This can be ordered under the heading "Accessories". According to VDE 0105 and IEC 364, all work on the electric drive may only be carried out by qualified personnel. As usual with variable speed gears, speed control by turning the handwheel is only permitted during operation! A change in speed while stationary can damage the stepless adjustment unit. All product photos are non-binding examples! Technical changes reserved.

Worm variable speed gear motor, Power= 0.18 kW, Speed= 4.5 - 22 rpm, Voltage= 3 x 230/400 V-50 Hz, 3 x 265/460 V-60 Hz (± 5% according to VDE 0530), Protection type= IP55, iso class= F (155°C), Operating mode= S1, Duty cycle= S1- 100%, Total length= approx. 459 mm, Hollow shaft= 25 mm, motor Speed= 4 poles, gear ratio with adjustment unit (i)= 64 - 328 Gear ratio only worm gear (i)= 40, torque= 38 Nm - 63 Nm, operating factor ( f.s.)= 1, terminal box= above (rotatable), weight= 13 kg, color= RAL 5010 (gentian blue), temperature sensor= 3 x PTC thermistors, gear housing = aluminum, ball bearing = SKF, C&U or equivalent, Cooling= axial fan (plastic). For technical reasons, the variable speed worm gear motor should cannot be operated with a frequency converter. The drive corresponds to IEC 60034-30:2008, is suitable for both directions of rotation and is supplied with an oil filling. Open hollow shafts are to be sealed with a cover cap. This can be ordered under the heading "Accessories". According to VDE 0105 and IEC 364, all work on the electric drive may only be carried out by qualified personnel. As usual with variable speed gears, speed control by turning the handwheel is only permitted during operation! A change in speed while stationary can damage the stepless adjustment unit. All product photos are non-binding examples! Technical changes reserved.

Worm variable speed gear motor, Power= 0.18 kW, Speed= 3 - 14.5 rpm, Voltage= 3 x 230/400 V-50 Hz, 3 x 265/460 V-60 Hz (± 5% according to VDE 0530), Protection type= IP55, Iso class= F (155°C), Operating mode= S1, Duty cycle= S1- 100%, Total length= approx. 459 mm, Hollow shaft = 25 mm, Motor speed = 4 poles, Translation with adjustment unit (i) = 96 - 492 Transmission only worm gear (i) = 60, torque = 50 Nm - 80 Nm, Service factor ( f.s.)= 1, Terminal box= above (rotatable), Weight= 13 kg, Color= RAL 5010 (gentian blue), temperature sensor= 3 x PTC thermistors, gear housing = aluminum, ball bearing = SKF, C&U or equivalent, Cooling= axial fan (plastic). For technical reasons, the variable speed worm gear motor should cannot be operated with a frequency converter. The drive corresponds to IEC 60034-30:2008, is suitable for both directions of rotation and is supplied with an oil filling. Open hollow shafts are to be sealed with a cover cap. This can be ordered under the heading "Accessories". According to VDE 0105 and IEC 364, all work on the electric drive may only be carried out by qualified personnel. As usual with variable speed gears, speed control by turning the handwheel is only permitted during operation! A change in speed while stationary can damage the stepless adjustment unit. All product photos are non-binding examples! Technical changes reserved.

Worm variable speed gear motor, power= 0.18 kW, speed= 2 – 8.5 rpm Voltage= 3 x 230/400 V-50 Hz, 3 x 265/460 V-60 Hz (± 5% in accordance with VDE 0530), Protection class= IP55, insulation class= F (155°C), operating mode= S1, duty cycle= S1- 100%, total length= approx. 459 mm, Hollow shaft= 25 mm, motor speed= 4 pole, gear ratio with adjustment unit (i)= 160 - 820,Gear ratio only worm gear (i)= 100, torque= 66 Nm – 79 Nm, operating factor (f.s.)= 1, Terminal box= top (rotatable), weight= 13 kg, color= RAL 5010 (gentian blue), Temperature sensor= 3 x PTC thermistors, gear housing= aluminum, ball bearings= SKF, C&U or equivalent, Cooling= axial fan (plastic). The drive complies with IEC 60034-30:2008, is suitable for both directions of rotation and is supplied with an oil filling. Open hollow shafts must be closed with a cover cap. This can be ordered under the "Accessories" section. In accordance with VDE 0105 or. According to IEC 364, all work on the electric drive must only be carried out by qualified specialist personnel. As is usual with variable speed drives, speed control by turning the handwheel is only permitted during operation! A speed change when the drive is at a standstill can lead to damage to the stepless adjustment unit. All product photos are non-binding examples! Technical changes reserved.

Worm variable speed gear motor, Power= 0.18 kW, Speed= 3.5 - 17.5 rpm, Voltage= 3 x 230/400 V-50 Hz, 3 x 265/460 V-60 Hz (± 5% according to VDE 0530), Protection type= IP55, iso class= F (155°C), Operating mode= S1, Duty cycle= S1- 100%, Total length= approx. 459 mm, Hollow shaft= 25 mm, motor Speed= 4 poles, gear ratio with adjustment unit (i)= 80 - 410 Gear ratio only worm gear (i)= 50, torque= 44 Nm - 73 Nm, operating factor ( f.s.)= 1, terminal box= above (rotatable), weight= 13 kg, color= RAL 5010 (gentian blue), temperature sensor= 3 x PTC thermistors, gear housing = aluminum, ball bearing = SKF, C&U or equivalent, Cooling= axial fan (plastic). For technical reasons, the variable speed worm gear motor should cannot be operated with a frequency converter. The drive corresponds to IEC 60034-30:2008, is suitable for both directions of rotation and is supplied with an oil filling. Open hollow shafts are to be sealed with a cover cap. This can be ordered under the heading "Accessories". According to VDE 0105 and IEC 364, all work on the electric drive may only be carried out by qualified personnel. As usual with variable speed gears, speed control by turning the handwheel is only permitted during operation! A change in speed while stationary can damage the stepless adjustment unit. All product photos are non-binding examples! Technical changes reserved.

Worm variable speed gear motor, Power= 0.25 kW, Speed= 27 - 133 Rpm, Voltage= 3 x 230/400 V-50 Hz, 3 x 265/460 V-60 Hz (± 5% according to VDE 0530), Protection type= IP55, iso class= F (155°C), Operating mode= S1, Duty cycle= S1- 100%, Total length= approx. 453 mm, Hollow shaft = 18 mm, Motor speed = 4 poles, Translation with adjustment unit (i) = 10.5 - 52.5 Transmission only worm gear (i) = 7.5, Torque = 13 Nm - 30 Nm, Service factor (f.s.)= 1, Terminal box= above (rotatable), Weight= 14 kg, Color= RAL 5010 (gentian blue), Temperature sensor= 3 x PTC thermistors, Gearbox housing = aluminium, Ball bearings = SKF, C&U or equivalent, Cooling= axial fan (plastic). For technical reasons, the variable speed worm gear motor should cannot be operated with a frequency converter. The drive corresponds to IEC 60034-30:2008, is suitable for both directions of rotation and is supplied with an oil filling. Open hollow shafts are to be sealed with a cover cap. This can be ordered under the heading "Accessories". In accordance with VDE 0105 and IEC 364, all work on the electric drive may only be carried out by qualified personnel. As usual with variable speed gears, speed control by turning the handwheel is only permitted during operation! A change in speed while stationary can damage the stepless adjustment unit. All product photos are non-binding examples! Technical changes reserved.

Worm variable speed gear motor, Power= 0.25 kW, Speed= 7 - 33 rpm, Voltage= 3 x 230/400 V-50 Hz, 3 x 265/460 V-60 Hz (± 5% according to VDE 0530), Protection type= IP55, Iso class= F (155°C), Operating mode= S1, Duty cycle= S1- 100%, Total length= approx. 453 mm, Hollow shaft = 18 mm, Motor speed = 4 poles, Translation with adjustment unit (i) = 42 - 210 Transmission only worm gear (i) = 30, Torque = 43 Nm - 89 Nm, Service factor ( f.s.)= 1, Terminal box= above (rotatable), Weight= 14 kg, Color= RAL 5010 (gentian blue), Temperature sensor= 3 x PTC Thermistors, Gear housing = aluminum, Ball bearing = SKF, C&U or equivalent, Cooling= axial fan (plastic). For technical reasons, the variable speed worm gear motor should cannot be operated with a frequency converter. The drive corresponds to IEC 60034-30:2008, is suitable for both directions of rotation and is supplied with an oil filling. Open hollow shafts are to be sealed with a cover cap. This can be ordered under the heading "Accessories". In accordance with VDE 0105 and IEC 364, all work on the electric drive may only be carried out by qualified personnel. As usual with variable speed gears, speed control by turning the handwheel is only permitted during operation! A change in speed while stationary can damage the stepless adjustment unit. All product photos are non-binding examples! Technical changes reserved.

Worm variable speed gear motor, power= 0.25 kW, Speed= 13.5 - 66.5 rpm, Voltage= 3 x 230/400 V-50 Hz, 3 x 265/460 V-60 Hz (± 5% according to VDE 0530), Protection type= IP55, Iso class= F (155°C), Operating mode= S1, Duty cycle= S1- 100%, Total length= approx. 453 mm, Hollow shaft = 18 mm, Motor speed = 4 poles, Translation with adjustment unit (i) = 21 - 105 Transmission only worm gear (i) = 15, Torque = 24 Nm - 53 Nm, Service factor ( f.s.)= 1, Terminal box= above (rotatable), Weight= 14 kg, Color= RAL 5010 (gentian blue), Temperature sensor= 3 x PTC thermistors, Gear housing = Aluminum, Ball bearing = SKF, C&U or equivalent, Cooling= axial fan (plastic). For technical reasons, the variable speed worm gear motor should cannot be operated with a frequency converter. The drive corresponds to IEC 60034-30:2008, is suitable for both directions of rotation and is supplied with an oil filling. Open hollow shafts are to be sealed with a cover cap. This can be ordered under the heading "Accessories". In accordance with VDE 0105 and IEC 364, all work on the electric drive may only be carried out by qualified personnel. As usual with variable speed gears, speed control by turning the handwheel is only permitted during operation! A change in speed while stationary can damage the stepless adjustment unit. All product photos are non-binding examples! Technical changes reserved.

Worm variable speed gear motor, power= 0.25 kW, Speed= 10 - 50 rpm, Voltage= 3 x 230/400 V-50 Hz, 3 x 265/460 V-60 Hz (± 5% according to VDE 0530), Protection type= IP55, iso class= F (155°C), Operating mode= S1, Duty cycle= S1- 100%, Total length= approx. 453 mm, Hollow shaft = 18 mm, motor speed = 4 poles, translation with adjustment unit (i) = 28 - 140 Transmission only worm gear (i) = 20, torque = 32 Nm - 68 Nm, service factor ( f.s.)= 1, terminal box= above (rotatable), weight= 14 kg, color= RAL 5010 (gentian blue), temperature sensor= 3 x PTC thermistors, gear housing = aluminum, ball bearing = SKF, C&U or equivalent, Cooling= axial fan (plastic). For technical reasons, the variable speed worm gear motor should cannot be operated with a frequency converter. The drive corresponds to IEC 60034-30:2008, is suitable for both directions of rotation and is supplied with an oil filling. Open hollow shafts are to be sealed with a cover cap. This can be ordered under the heading "Accessories". In accordance with VDE 0105 and IEC 364, all work on the electric drive may only be carried out by qualified personnel. As usual with variable speed gears, speed control by turning the handwheel is only permitted during operation! A change in speed while stationary can damage the stepless adjustment unit. All product photos are non-binding examples! Technical changes reserved.

Worm variable speed gear motor, Power= 0.25 kW, Speed= 20 - 100 rpm, Voltage= 3 x 230/400 V-50 Hz, 3 x 265/460 V-60 Hz (± 5% according to VDE 0530), Protection type= IP55, iso class= F (155°C), Operating mode= S1, Duty cycle= S1- 100%, Total length= approx. 453 mm, Hollow shaft = 18 mm, motor speed = 4 poles, translation with adjustment unit (i) = 14 - 70 Transmission only worm gear (i) = 10, torque = 16 Nm - 38 Nm, service factor ( f.s.)= 1, terminal box= above (rotatable), weight= 14 kg, color= RAL 5010 (gentian blue), temperature sensor= 3 x PTC thermistors, gear housing = aluminum, ball bearing = SKF, C&U or equivalent, Cooling= axial fan (plastic). For technical reasons, the variable speed worm gear motor should cannot be operated with a frequency converter. The drive corresponds to IEC 60034-30:2008, is suitable for both directions of rotation and is supplied with an oil filling. Open hollow shafts are to be sealed with a cover cap. This can be ordered under the heading "Accessories". In accordance with VDE 0105 and IEC 364, all work on the electric drive may only be carried out by qualified personnel. As usual with variable speed gears, speed control by turning the hand wheel is only permitted during operation! A change in speed while stationary can damage the stepless adjustment unit. All product photos are non-binding examples! Technical changes reserved.

Worm variable speed gear motor, Power= 0.25 kW, Speed= 8 - 40 rpm, Voltage= 3 x 230/400 V-50 Hz, 3 x 265/460 V-60 Hz (± 5% according to VDE 0530), Protection type= IP55, Iso class= F (155°C), Operating mode= S1, Duty cycle= S1- 100%, Total length= Approx. 453 mm, Hollow shaft = 18 mm, Motor speed = 4 poles, Translation with adjustment unit (i) = 35 - 175 Transmission only worm gear (i) = 25, Torque = 38 Nm - 80 Nm, Service factor ( f.s.)= 1, terminal box= above (rotatable), Weight= 14 kg, Color= RAL 5010 (gentian blue), Temperature sensor= 3 x PTC thermistors, Gear housing = Aluminum, Ball bearing = SKF, C&U or equivalent, Cooling= axial fan (plastic). For technical reasons, the variable speed worm gear motor should cannot be operated with a frequency converter. The drive corresponds to IEC 60034-30:2008, is suitable for both directions of rotation and is supplied with an oil filling. Open hollow shafts are to be sealed with a cover cap. This can be ordered under the heading "Accessories". In accordance with VDE 0105 and IEC 364, all work on the electric drive may only be carried out by qualified personnel. As usual with variable speed gears, speed control by turning the handwheel is only permitted during operation! A change in speed while stationary can damage the stepless adjustment unit. All product photos are non-binding examples! Technical changes reserved.

Worm variable speed gear motor, Power= 0.25 kW, Speed= 2.5 - 12.5 rpm, Voltage= 3 x 230/400 V-50 Hz, 3 x 265/460 V-60 Hz (± 5% according to VDE 0530), Protection type= IP55, iso class= F (155°C), Operating mode= S1, Duty cycle= S1- 100%, Total length= approx. 473 mm, Hollow shaft = 25 mm, motor speed = 4 poles, translation with adjustment unit (i) = 112 - 560 Transmission only worm gear (i) = 80, torque = 72 Nm - 120 Nm, operating factor ( f.s.)= 1, terminal box= above (rotatable), weight= 14 kg, color= RAL 5010 (gentian blue), temperature sensor= 3 x PTC thermistors, gear housing = aluminum, ball bearing = SKF, C&U or equivalent, Cooling= axial fan (plastic). For technical reasons, the variable speed worm gear motor should cannot be operated with a frequency converter. The drive corresponds to IEC 60034-30:2008, is suitable for both directions of rotation and is supplied with an oil filling. Open hollow shafts are to be sealed with a cover cap. This can be ordered under the heading "Accessories". In accordance with VDE 0105 and IEC 364, all work on the electric drive may only be carried out by qualified personnel. As usual with variable speed gears, speed control by turning the handwheel is only permitted during operation! A change in speed while stationary can damage the stepless adjustment unit. All product photos are non-binding examples! Technical changes reserved.

Worm variable speed gear motor, Power= 0.25 kW, Speed= 5 - 25 rpm, Voltage= 3 x 230/400 V-50 Hz, 3 x 265/460 V-60 Hz (± 5% according to VDE 0530), Protection type= IP55, iso class= F (155°C), Operating mode= S1, Duty cycle= S1- 100%, Total length= approx. 473 mm, Hollow shaft = 25 mm, motor speed = 4 poles, translation with adjustment unit (i) = 56 - 280 Transmission only worm gear (i) = 40, torque = 54 Nm - 112 Nm, service factor ( f.s.)= 1, terminal box= above (rotatable), weight= 14 kg, color= RAL 5010 (gentian blue), temperature sensor= 3 x PTC thermistors, gear housing = aluminum, ball bearing = SKF, C&U or equivalent, Cooling= axial fan (plastic). For technical reasons, the variable speed worm gear motor should cannot be operated with a frequency converter. The drive corresponds to IEC 60034-30:2008, is suitable for both directions of rotation and is supplied with an oil filling. Open hollow shafts are to be sealed with a cover cap. This can be ordered under the heading "Accessories". In accordance with VDE 0105 and IEC 364, all work on the electric drive may only be carried out by qualified personnel. As usual with variable speed gears, speed control by turning the hand wheel is only permitted during operation! A change in speed while stationary can damage the stepless adjustment unit. All product photos are non-binding examples! Technical changes reserved.

Worm variable speed gear motor, Power= 0.25 kW, Speed= 4 - 20 rpm, Voltage= 3 x 230/400 V-50 Hz, 3 x 265/460 V-60 Hz (± 5% according to VDE 0530), Protection type= IP55, iso class= F (155°C), Operating mode= S1, Duty cycle= S1- 100%, Total length= approx. 473 mm, Hollow shaft = 25 mm, motor speed = 4 poles, translation with adjustment unit (i) = 70 - 350 Transmission only worm gear (i) = 50, torque = 59 Nm - 122 Nm, service factor ( f.s.)= 1, terminal box= above (rotatable), weight= 14 kg, color= RAL 5010 (gentian blue), temperature sensor= 3 x PTC thermistors, gear housing = aluminum, ball bearing = SKF, C&U or equivalent, Cooling= axial fan (plastic). For technical reasons, the variable speed worm gear motor should cannot be operated with a frequency converter. The drive corresponds to IEC 60034-30:2008, is suitable for both directions of rotation and is supplied with an oil filling. Open hollow shafts are to be sealed with a cover cap. This can be ordered under the heading "Accessories". In accordance with VDE 0105 and IEC 364, all work on the electric drive may only be carried out by qualified personnel. As usual with variable speed gears, speed control by turning the handwheel is only permitted during operation! A change in speed while stationary can damage the stepless adjustment unit. All product photos are non-binding examples! Technical changes reserved.

Worm variable speed gear motor, Power= 0.25 kW, Speed= 3.5 - 16.5 rpm, Voltage= 3 x 230/400 V-50 Hz, 3 x 265/460 V-60 Hz (± 5% according to VDE 0530), Protection type= IP55, iso class= F (155°C), Operating mode= S1, Duty cycle= S1- 100%, Total length= approx. 473 mm, Hollow shaft = 25 mm, motor speed = 4 poles, translation with adjustment unit (i) = 84 - 420 Transmission only worm gear (i) = 60, torque = 66 Nm - 135 Nm, service factor ( f.s.)= 1, terminal box= above (rotatable), weight= 14 kg, color= RAL 5010 (gentian blue), temperature sensor= 3 x PTC thermistors, gear housing = aluminum, ball bearing = SKF, C&U or equivalent, Cooling= axial fan (plastic). For technical reasons, the variable speed worm gear motor should cannot be operated with a frequency converter. The drive corresponds to IEC 60034-30:2008, is suitable for both directions of rotation and is supplied with an oil filling. Open hollow shafts are to be sealed with a cover cap. This can be ordered under the heading "Accessories". According to VDE 0105 and IEC 364, all work on the electric drive may only be carried out by qualified personnel. As usual with variable speed gears, speed control by turning the hand wheel is only permitted during operation! A change in speed while stationary can damage the stepless adjustment unit. All product photos are non-binding examples! Technical changes reserved.

Worm variable speed gear motor, Power= 0.37 kW, Speed= 7 - 33 rpm, Voltage= 3 x 230/400 V-50 Hz, 3 x 265/460 V-60 Hz (± 5% according to VDE 0530), Protection type= IP55, iso class= F (155°C), Operating mode= S1, Duty cycle= S1- 100%, Total length= approx. 473 mm, Hollow shaft = 25 mm, motor speed = 4 poles, translation with adjustment unit (i) = 42 - 210 Transmission only worm gear (i) = 30, torque = 61 Nm - 107 Nm, service factor ( f.s.)= 1, terminal box= above (rotatable), weight= 15 kg, color= RAL 5010 (gentian blue), temperature sensor= 3 x PTC thermistor, gear housing = aluminum, ball bearing = SKF, C&U or equivalent, Cooling= axial fan (plastic). For technical reasons, the variable speed worm gear motor should cannot be operated with a frequency converter. The drive corresponds to IEC 60034-30:2008, is suitable for both directions of rotation and is supplied with an oil filling. Open hollow shafts are to be sealed with a cover cap. This can be ordered under the heading "Accessories". According to VDE 0105 and IEC 364, all work on the electric drive may only be carried out by qualified personnel. As usual with variable speed gears, speed control by turning the handwheel is only permitted during operation! A change in speed while stationary can damage the stepless adjustment unit. All product photos are non-binding examples! Technical changes reserved.