KV002-DC350-2-0.5 kW-270 U/min Bevel gear motor
Product information "KV002-DC350-2-0.5 kW-270 U/min Bevel gear motor"
Bevel gear motor with DC motor, IP66, power = 0.5 kW (S2 operation), speed = 270 rpm
Voltage = 12 or 24 volts DC, protection class = gearbox IP55, motor IP66, current consumption = 12V/58.8 A, 24V/29.4 A,
Operating mode = S2 (short-term operation), hollow shaft = 20 mm, motor speed = 2 pole, gear ratio (i) = 11.09
Torque = 17 Nm, service factor (fs) = 4.0, connection = clamping bolt, weight = 16.0 kg
An external speed control is optionally available. The gearbox can be operated in both directions of rotation
and is supplied with an oil filling. According to VDE 0105 and IEC 364, all work on the
electric drive may only be carried out by qualified specialist personnel.
All product photos are non-binding examples! Technical changes reserved.
When ordering, please select the desired installation position and version!
| Performance: | 0,50 kW |
|---|---|
| Torque: | 11 to 25 Nm |
| Rotation speed: | 201 to 300 rpm |
| Shaft diameter: | 20 mm |
| Series: | K-series |
Accesories
Double output shaft with key father for helical gear reducer KV002 and KV003. 20 x 40 mm The shaft is permanently installed and can only be ordered with geared motor All product photos are non-binding examples!
Double output shaft with key for bevel gearboxes KV002 and KV003. 20x40mm The shaft is permanently installed and can only be ordered with a geared motor + flange. All product photos are non-binding examples! Technical changes reserved.
Output flange for helical gear reducer KV002 and KV003. All product photos are non-binding examples! Technical changes reserved.
Output shaft with key father for helical gear reducer KV002 and KV003. 20 x 40 mm The shaft is permanently installed and can only be ordered with geared motor + flange.. Please indicate the installation side (starting from installation position M1). All product photos are non-binding examples!
Torque arm for helical gear reducer KV002 and KV003. All product photos are non-binding examples! Technical changes reserved.
Output shaft with key father for helical gear reducer KV002 and KV003. 20 x 40 mm The shaft is permanently installed and can only be ordered with geared motor Please indicate the installation side (starting from installation position M1). All product photos are non-binding examples!
Speed control for DC motors The PLN40 speed control is suitable for DC motors up to500 W / 40 A.Extensive control variants of the DC motor are possible. These can be found in the catalog included in the download. Dimensions: 146 mm x 177 mm x 34 mm DC Motor on and off times:- Acceleration time: 0.5 - 10 sec- Deceleration time: 0.5 - 10 sec Alle Produktfotos sind unverbindliche Beispiele! Technische Änderungen vorbehalten.
Speed control for DC motors The PLN20 speed control is suitable for DC motors up to 350 W / 20 A.Extensive control variants of the DC motor are possible. These can be found in the catalog included in the download. Motor start and stop times:- Acceleration ramp: 0.5 - 10 sec- Deceleration ramp: 0.5 - 10 sec Special features:Room temperature: 0°C / +40°C (alarm below zero) Dimensions:146 mm x 177 mm x 34 mm Attention: Individual electrical protection must be carried out on site by qualified personnel! Alle Produktfotos sind unverbindliche Beispiele! Technische Änderungen vorbehalten.
Speed control for DC motors in the control box Pre-wired DC motor control unit with potentiometer (5–10 kΩ), left-off-right rotation switch and motor control mounted in the control box. The speed control is suitable for DC motorsup to 500 W / 40 A . Motor switch-on and switch-off times:- Acceleration ramp: 0.5 - 10 sec- Deceleration ramp: 0.5 - 10 sec Special features:Room temperature: 0°C / +40°C (alarm below zero) Dimensions:350 mm x 250 mm x 155 mmAttention: Individual electrical protection must be carried out on site by qualified personnel! Alle Produktfotos sind unverbindliche Beispiele! Technische Änderungen vorbehalten.
Speed control for DC motors in the control box Pre-wired DC motor control unit with potentiometer (5–10 kΩ), left-off-right rotation switch and motor control mounted in the control box. The speed control is suitable for DC motorsup to 350 W / 20 A . Motor switch-on and switch-off times:- Acceleration ramp: 0.5 - 10 sec- Deceleration ramp: 0.5 - 10 sec Special features:Room temperature: 0°C / +40°C (alarm below zero) Dimensions:350 mm x 250 mm x 155 mmAttention: Individual electrical protection must be carried out on site by qualified personnel! Alle Produktfotos sind unverbindliche Beispiele! Technische Änderungen vorbehalten.