Single phase motor -ML2 90S-4, 1,1 kW, 4pol, B14
Product information "Single phase motor -ML2 90S-4, 1,1 kW, 4pol, B14"
Single-phase motor with Operating and starting capacitor
Power= 1.1 kW, Speed= 4 pole, Voltage= 1 x 230 V (± 5% according to VDE 0530), Design= B14,
Weight approx. 14.7 kg, Shaft = 24 x 50 mm, Frequency= 50 Hertz, Protection class= IP55, Operating mode= S1- 100% ED,
Temperature sensor= 1 x PTO thermal sensor, Cooling= axial fan (plastic). Insulation class= F (155°C),
Efficiency class= IE2, Efficiency= 81.4%, Terminal box= aluminum, Terminal box position= top,
Housing= die-cast aluminum, Ball bearings= SKF, C&U, or equivalent.
AC motors are suitable for both directions of rotation.
Optional:
On/off switch with reversing switch for left/right rotation, underVoltage release,
Collar plug= 1 x 230 V, Switching capacity= 16 A, Ambient temperature= -5°C to +40°C,
Cable between motor and switch housing= approx. 90 cm.
General:
Due to the start-up and Operating capacitor gives the 230V motor a stronger starting torque.
The starting capacitor is switched off by a starting relay when the Speed is reached.
Speed control via Frequency converters or similar therefore leads to faults and is not permitted.
All product photos are non-binding examples! Technical changes reserved.
| Ambient temperature: | 40 °C |
|---|---|
| Engine protection: | Thermocouple PTO- single |
| Flange dimensions: | 140 x 95 x 115 mm |
| Frequency: | 50 Hz |
| Installation altitude: | 1000 m |
| Kühlungsart: | IC 411 |
| Operating mode: | S1 |
| Performance: | 1,1 kW |
| Shaft dimensions: | 24 x 50 mm |
| Rotation speed: | 1500 rpm / 4 polig |
| Shaft diameter: | 24 mm |
| Type of construction: | B14 |
| Tension: | 1 x 230 V |
| Protection class: | IP55 |
| Direction of rotation: | Left, Right |
| Efficiency Class: | IE 2 |
Accesories
Motor switch (on-off) with selector switch right / left for 0.12 - 2.2kW at 1x 230V, for external installation, cable length approx. 90cm, Description:- Undervoltage release,- Switching capacity 16 A - 1x230V,- Ambient temperature -5°C to +40°C- Collar plug 1x230 V. Switching the direction of rotation only when the motor is at a standstill!
Heating band for a standstill heater for electric motors of size 56-63-71-80-90 The standstill heater is used to prevent the formation of condensation during breaks in operation.
Stainless steel worm gear motor, Power= 0,75 kW, Speed= 93,3 rpmVoltage= 3 x 230/400 V-50 Hz, 3 x 265/460 V-60 Hz (± 5% In according to the VDE 0530), Degree of protection= IP55, Insulation class= F (155°C), Operating mode= S1, Type of duty= S1- 100%, Hollow shaft= 25mm, Engine Speed= 4 pole, Ratio (i)= 15, Torque= 63 Nm, Permitted overhung loads (radial)= 2270 N, Service factor (f.s.)= 1,2, Cable outlet = on the back, Weight= 34 kg, Temperature sensor= 3 x PTC-thermistors, Housing= AISI 304 (V2A), Ball bearings= SKF, C & U or equivalent. The worm geared motor is suitable for frequency converter use and complies with IEC 60034-30: 2008. The geared motor can be operated in both directions and contains an oil filling on delivery. In according to the VDE 0105 bzw. IEC 364 all work on the electric drive must only becarried out by qualified specialist personnel. For modifications or special designs please send inquiry. Important instructionsThis drive is a custom-made product. A resignation or revocation of the purchase is excluded!All product photos are non-binding examples!
Protective roof (without hood) for electric motors in size 90 Diameter: Ø170 mm If ordered with a motor, the protective roof can also be delivered assembled. Please select. All product photos are non-binding examples! Technical changes reserved.