Worm Gear Motor, Power= 1,1 KW, Speed= 6 to 67 rpmDegree of protection= IP55, Insulation class= F (155°C), Operating mode= S1, Type of duty= S1- 100%,Hollow shaft= 25mm, Engine Speed= 4 pole, Ratio (i)= 25, Torque= 146 Nm,Service factor (f.s.)= 0,9 . Terminal box= top (rotatable), Weight= 23,2 kg, Paint= RAL 5010 (gentian blue),Temperature sensor= 3 x PTC-thermistors, Housing= Aluminum or cast iron, Ball bearings= SKF, C & U or equivalent, Frequency InverterPower= 1.1 KW, Size= A, Input Voltage= 3 x 400V + 10% (three-phase), Input frequency= 50/60 Hz,Output frequency= 0-400 Hz, EMC filter= C2, Degree of protection= IP65, Dimensions= 233mm x 153mm x 120mm,Mains current (input)= 2.6 A. Ideal control range= 5-60 Hz, below 30 Hz, a forced cooling fan is used for coolingneeded. Product Information The frequency converter optionally offers the possibility of becoming "bus-capable" with the aid of fieldbus modules. With CANopen, EtherCAT, Modbus (already included), Profibus, Profinet and Sercos the EASYdrive offers Compatibility with almost all common interfaces. The customer can choose the relevant bus system for him and integrate the EASYdrive ideally in the control environment of its application.The required optional control variant must be specified for orders.The EASYdrive lasts without external filter measures the EMC class C2 (for 3-phase mains supply), or C1 (for 1-phase mains supply). ! Possible variant selection! Product selection When selecting the frequency converter, make sure that there are 3 variants. First, this includes the devicein the standard version, secondly the device with a membrane keyboard and thirdly the device with an MMI operating unit.The illustrated "frequency converter in standard version" is fully usable and contains a built-in potentiometer,but needs to control a corresponding control panel.For this purpose, one of the following options must be ordered: - External HMI device (MMI with cable and plug)- Interface cable for PC programming- Bluetooth adapter The variant "Frequency inverter with membrane keypad" offers the possibility to directly control the FI,such as Start-stop, left-right-run etc.For parameterization, one of the following options must also be ordered::- External HMI device (MMI with cable and plug)- Interface cable for PC programming- Bluetooth adapter The variant "Frequency converter with MMI operating unit" does not require an optional operating unitIn addition, a display is included in the device cover. The mentioned options can be used if required. Important notesThis drive is a custom-made product. A withdrawal or cancellation of the purchase is excluded!All product photos are non-binding examples!
Worm Gear Motor, Power= 1,1 KW, Speed= 6 to 67 rpm, Degree of protection= IP55, Insulation class= F (155°C), Operating mode= S1, Type of duty= S1- 100%,Hollow shaft= 25mm, Engine Speed= 4 pole, Ratio (i)= 25, Torque= 146 Nm,Service factor (f.s.)= 0,9 . Terminal box= top (rotatable), Weight= 23,2 kg, Paint= RAL 5010 (gentian blue),Temperature sensor= 3 x PTC-thermistors, Housing= Aluminum or cast iron, Ball bearings= SKF, C & U or equivalent, Frequency InverterPower= 1.1 KW, Size= A, Input Voltage= 1 x 230V +10% (single phase), Input frequency= 50/60 Hz,Output frequency= 0-400 Hz, EMC filter= C1, Degree of protection= IP65, Dimensions= 233mm x 153mm x 120mm,Mains current (input)= 9.2 A. Ideal control range= 5-60 Hz, below 30 Hz, a forced cooling fan is used for coolingneeded. Product Information The frequency converter optionally offers the possibility of becoming "bus-capable" with the aid of fieldbus modules. With CANopen, EtherCAT, Modbus (already included), Profibus, Profinet and Sercos the EASYdrive offers Compatibility with almost all common interfaces. The customer can choose the relevant bus system for him and integrate the EASYdrive ideally in the control environment of its application.The required optional control variant must be specified for orders.The EASYdrive lasts without external filter measures the EMC class C2 (for 3-phase mains supply), or C1 (for 1-phase mains supply). ! Possible variant selection! Product selection When selecting the frequency converter, make sure that there are 3 variants. First, this includes the devicein the standard version, secondly the device with a membrane keyboard and thirdly the device with an MMI operating unit.The illustrated "frequency converter in standard version" is fully usable and contains a built-in potentiometer,but needs to control a corresponding control panel.For this purpose, one of the following options must be ordered: - External HMI device (MMI with cable and plug)- Interface cable for PC programming- Bluetooth adapter The variant "Frequency inverter with membrane keypad" offers the possibility to directly control the FI,such as Start-stop, left-right-run etc.For parameterization, one of the following options must also be ordered::- External HMI device (MMI with cable and plug)- Interface cable for PC programming- Bluetooth adapter The variant "Frequency converter with MMI operating unit" does not require an optional operating unitIn addition, a display is included in the device cover. The mentioned options can be used if required. Important notesThis drive is a custom-made product. A withdrawal or cancellation of the purchase is excluded!All product photos are non-binding examples!
Worm Gear Motor, Power= 1,1 KW, Speed= 9 to 110 rpm, Degree of protection= IP55, Insulation class= F (155°C), Operating mode= S1, Type of duty= S1- 100%,Hollow shaft= 25mm, Engine Speed= 4 pole, Ratio (i)= 15, Torque= 93 Nm,Service factor (f.s.)= 1,5 . Terminal box= top (rotatable), Weight= 23,2 kg, Paint= RAL 5010 (gentian blue),Temperature sensor= 3 x PTC-thermistors, Housing= Aluminum or cast iron, Ball bearings= SKF, C & U or equivalent, Frequency InverterPower= 1.1 KW, Size= A, Input Voltage= 1 x 230V +10% (single phase), Input frequency= 50/60 Hz,Output frequency= 0-400 Hz, EMC filter= C1, Degree of protection= IP65, Dimensions= 233mm x 153mm x 120mm,Mains current (input)= 9.2 A. Ideal control range= 5-60 Hz, below 30 Hz, a forced cooling fan is used for coolingneeded. Product Information The frequency converter optionally offers the possibility of becoming "bus-capable" with the aid of fieldbus modules. With CANopen, EtherCAT, Modbus (already included), Profibus, Profinet and Sercos the EASYdrive offers Compatibility with almost all common interfaces. The customer can choose the relevant bus system for him and integrate the EASYdrive ideally in the control environment of its application.The required optional control variant must be specified for orders.The EASYdrive lasts without external filter measures the EMC class C2 (for 3-phase mains supply), or C1 (for 1-phase mains supply). ! Possible variant selection! Product selection When selecting the frequency converter, make sure that there are 3 variants. First, this includes the devicein the standard version, secondly the device with a membrane keyboard and thirdly the device with an MMI operating unit.The illustrated "frequency converter in standard version" is fully usable and contains a built-in potentiometer,but needs to control a corresponding control panel.For this purpose, one of the following options must be ordered: - External HMI device (MMI with cable and plug)- Interface cable for PC programming- Bluetooth adapter The variant "Frequency inverter with membrane keypad" offers the possibility to directly control the FI,such as Start-stop, left-right-run etc.For parameterization, one of the following options must also be ordered::- External HMI device (MMI with cable and plug)- Interface cable for PC programming- Bluetooth adapter The variant "Frequency converter with MMI operating unit" does not require an optional operating unitIn addition, a display is included in the device cover. The mentioned options can be used if required. Important notesThis drive is a custom-made product. A withdrawal or cancellation of the purchase is excluded!All product photos are non-binding examples!
Worm Gear Motor, Power= 1,5 KW, Speed= 14 to 168 rpm, Degree of protection= IP55, Insulation class= F (155°C), Operating mode= S1, Type of duty= S1- 100%,Hollow shaft= 25mm, Engine Speed= 4 pole, Ratio (i)= 10, Torque= 89 Nm,Service factor (f.s.)= 1,5 . Terminal box= top (rotatable), Weight= 27,2 kg, Paint= RAL 5010 (gentian blue),Temperature sensor= 3 x PTC-thermistors, Housing= Aluminum or cast iron, Ball bearings= SKF, C & U or equivalent, Frequency InverterPower= 1.5 KW, Size= A, Input Voltage= 3 x 400V + 10% (three-phase), Input frequency= 50/60 Hz,Output frequency= 0-400 Hz, EMC filter= C2, Degree of protection= IP65, Dimensions= 233mm x 153mm x 120mm,Mains current (input)= 3.3 A. Ideal control range= 5-60 Hz, below 30 Hz, a forced cooling fan is used for coolingneeded. Product Information The frequency converter optionally offers the possibility of becoming "bus-capable" with the aid of fieldbus modules. With CANopen, EtherCAT, Modbus (already included), Profibus, Profinet and Sercos the EASYdrive offers Compatibility with almost all common interfaces. The customer can choose the relevant bus system for him and integrate the EASYdrive ideally in the control environment of its application.The required optional control variant must be specified for orders.The EASYdrive lasts without external filter measures the EMC class C2 (for 3-phase mains supply), or C1 (for 1-phase mains supply). ! Possible variant selection! Product selection When selecting the frequency converter, make sure that there are 3 variants. First, this includes the devicein the standard version, secondly the device with a membrane keyboard and thirdly the device with an MMI operating unit.The illustrated "frequency converter in standard version" is fully usable and contains a built-in potentiometer,but needs to control a corresponding control panel.For this purpose, one of the following options must be ordered: - External HMI device (MMI with cable and plug)- Interface cable for PC programming- Bluetooth adapter The variant "Frequency inverter with membrane keypad" offers the possibility to directly control the FI,such as Start-stop, left-right-run etc.For parameterization, one of the following options must also be ordered:: - External HMI device (MMI with cable and plug)- Interface cable for PC programming- Bluetooth adapter The variant "Frequency converter with MMI operating unit" does not require an optional operating unitIn addition, a display is included in the device cover. The mentioned options can be used if required. Important notesThis drive is a custom-made product. A withdrawal or cancellation of the purchase is excluded!All product photos are non-binding examples!
Worm Gear Motor, Power= 1,5 KW, Speed= 9 to 110 rpm, Degree of protection= IP55, Insulation class= F (155°C), Operating mode= S1, Type of duty= S1- 100%,Hollow shaft= 25mm, Engine Speed= 4 pole, Ratio (i)= 15, Torque= 127 Nm,Service factor (f.s.)= 1,1 . Terminal box= top (rotatable), Weight= 27,2 kg, Paint= RAL 5010 (gentian blue),Temperature sensor= 3 x PTC-thermistors, Housing= Aluminum or cast iron, Ball bearings= SKF, C & U or equivalent, Frequency InverterPower= 1.5 KW, Size= A, Input Voltage= 3 x 400V + 10% (three-phase), Input frequency= 50/60 Hz,Output frequency= 0-400 Hz, EMC filter= C2, Degree of protection= IP65, Dimensions= 233mm x 153mm x 120mm,Mains current (input)= 3.3 A. Ideal control range= 5-60 Hz, below 30 Hz, a forced cooling fan is used for coolingneeded. Product Information The frequency converter optionally offers the possibility of becoming "bus-capable" with the aid of fieldbus modules. With CANopen, EtherCAT, Modbus (already included), Profibus, Profinet and Sercos the EASYdrive offers Compatibility with almost all common interfaces. The customer can choose the relevant bus system for him and integrate the EASYdrive ideally in the control environment of its application.The required optional control variant must be specified for orders.The EASYdrive lasts without external filter measures the EMC class C2 (for 3-phase mains supply), or C1 (for 1-phase mains supply). ! Possible variant selection! Product selection When selecting the frequency converter, make sure that there are 3 variants. First, this includes the devicein the standard version, secondly the device with a membrane keyboard and thirdly the device with an MMI operating unit.The illustrated "frequency converter in standard version" is fully usable and contains a built-in potentiometer,but needs to control a corresponding control panel.For this purpose, one of the following options must be ordered: - External HMI device (MMI with cable and plug)- Interface cable for PC programming- Bluetooth adapter The variant "Frequency inverter with membrane keypad" offers the possibility to directly control the FI,such as Start-stop, left-right-run etc.For parameterization, one of the following options must also be ordered:: - External HMI device (MMI with cable and plug)- Interface cable for PC programming- Bluetooth adapter The variant "Frequency converter with MMI operating unit" does not require an optional operating unitIn addition, a display is included in the device cover. The mentioned options can be used if required. Important notesThis drive is a custom-made product. A withdrawal or cancellation of the purchase is excluded!All product photos are non-binding examples!
Worm Gear Motor, Power= 0,75 KW, Speed= 6 to 67 rpm, Degree of protection= IP55, Insulation class= F (155°C), Operating mode= S1, Type of duty= S1- 100%,Hollow shaft= 28mm, Engine Speed= 4 pole, Ratio (i)= 25, Torque= 102 Nm,Service factor (f.s.)= 2 . Terminal box= top (rotatable), Weight= 21 kg, Paint= RAL 5010 (gentian blue),Temperature sensor= 3 x PTC-thermistors, Housing= Aluminum or cast iron, Ball bearings= SKF, C & U or equivalent, Frequency InverterPower= 0.75 KW, Size= A, Input Voltage= 3 x 400V + 10% (three-phase), Input frequency= 50/60 Hz,Output frequency= 0-400 Hz, EMC filter= C2, Degree of protection= IP65, 233mm x 153mm x 120mm,Mains current (input)= 1.9 A. Ideal control range= 5-60 Hz, below 30 Hz, a forced cooling fan is used for coolingneeded. Product Information The frequency converter optionally offers the possibility of becoming "bus-capable" with the aid of fieldbus modules. With CANopen, EtherCAT, Modbus (already included), Profibus, Profinet and Sercos the EASYdrive offers Compatibility with almost all common interfaces. The customer can choose the relevant bus system for him and integrate the EASYdrive ideally in the control environment of its application.The required optional control variant must be specified for orders.The EASYdrive lasts without external filter measures the EMC class C2 (for 3-phase mains supply), or C1 (for 1-phase mains supply). ! Possible variant selection! Product selection When selecting the frequency converter, make sure that there are 3 variants. First, this includes the devicein the standard version, secondly the device with a membrane keyboard and thirdly the device with an MMI operating unit.The illustrated "frequency converter in standard version" is fully usable and contains a built-in potentiometer,but needs to control a corresponding control panel.For this purpose, one of the following options must be ordered: - External HMI device (MMI with cable and plug)- Interface cable for PC programming- Bluetooth adapter The variant "Frequency inverter with membrane keypad" offers the possibility to directly control the FI,such as Start-stop, left-right-run etc.For parameterization, one of the following options must also be ordered:: - External HMI device (MMI with cable and plug)- Interface cable for PC programming- Bluetooth adapter The variant "Frequency converter with MMI operating unit" does not require an optional operating unitIn addition, a display is included in the device cover. The mentioned options can be used if required. Important notesThis drive is a custom-made product. A withdrawal or cancellation of the purchase is excluded!All product photos are non-binding examples!
Worm Gear Motor, Power= 0,75 KW, Speed= 4 to 42 rpm, Degree of protection= IP55, Insulation class= F (155°C), Operating mode= S1, Type of duty= S1- 100%,Hollow shaft= 28mm, Engine Speed= 4 pole, Ratio (i)= 40, Torque= 147 Nm,Service factor (f.s.)= 1,5 . Terminal box= top (rotatable), Weight= 21 kg, Paint= RAL 5010 (gentian blue),Temperature sensor= 3 x PTC-thermistors, Housing= Aluminum or cast iron, Ball bearings= SKF, C & U or equivalent, Frequency InverterPower= 0.75 KW, Size= A, Input Voltage= 3 x 400V + 10% (three-phase), Input frequency= 50/60 Hz,Output frequency= 0-400 Hz, EMC filter= C2, Degree of protection= IP65, 233mm x 153mm x 120mm,Mains current (input)= 1.9 A. Ideal control range= 5-60 Hz, below 30 Hz, a forced cooling fan is used for coolingneeded. Product Information The frequency converter optionally offers the possibility of becoming "bus-capable" with the aid of fieldbus modules. With CANopen, EtherCAT, Modbus (already included), Profibus, Profinet and Sercos the EASYdrive offers Compatibility with almost all common interfaces. The customer can choose the relevant bus system for him and integrate the EASYdrive ideally in the control environment of its application.The required optional control variant must be specified for orders.The EASYdrive lasts without external filter measures the EMC class C2 (for 3-phase mains supply), or C1 (for 1-phase mains supply). ! Possible variant selection! Product selection When selecting the frequency converter, make sure that there are 3 variants. First, this includes the devicein the standard version, secondly the device with a membrane keyboard and thirdly the device with an MMI operating unit.The illustrated "frequency converter in standard version" is fully usable and contains a built-in potentiometer,but needs to control a corresponding control panel.For this purpose, one of the following options must be ordered: - External HMI device (MMI with cable and plug)- Interface cable for PC programming- Bluetooth adapter The variant "Frequency inverter with membrane keypad" offers the possibility to directly control the FI,such as Start-stop, left-right-run etc.For parameterization, one of the following options must also be ordered:: - External HMI device (MMI with cable and plug)- Interface cable for PC programming- Bluetooth adapter The variant "Frequency converter with MMI operating unit" does not require an optional operating unitIn addition, a display is included in the device cover. The mentioned options can be used if required. Important notesThis drive is a custom-made product. A withdrawal or cancellation of the purchase is excluded!All product photos are non-binding examples!
Worm Gear Motor, Power= 0,75 KW, Speed= 4 to 42 rpm, Degree of protection= IP55, Insulation class= F (155°C), Operating mode= S1, Type of duty= S1- 100%,Hollow shaft= 28mm, Engine Speed= 4 pole, Ratio (i)= 40, Torque= 147 Nm,Service factor (f.s.)= 1,5 . Terminal box= top (rotatable), Weight= 21 kg, Paint= RAL 5010 (gentian blue),Temperature sensor= 3 x PTC-thermistors, Housing= Aluminum or cast iron, Ball bearings= SKF, C & U or equivalent, Frequency InverterPower= 0.75 KW, Size= A, Input Voltage= 1 x 230V +10% (single phase), Input frequency= 50/60 Hz,Output frequency= 0-400 Hz, EMC filter= C1, Degree of protection= IP65, Dimensions= 233mm x 153mm x 120mm,Mains current (input)= 6.9 A. Ideal control range= 5-60 Hz, below 30 Hz, a forced cooling fan is used for coolingneeded. Product Information The frequency converter optionally offers the possibility of becoming "bus-capable" with the aid of fieldbus modules. With CANopen, EtherCAT, Modbus (already included), Profibus, Profinet and Sercos the EASYdrive offers Compatibility with almost all common interfaces. The customer can choose the relevant bus system for him and integrate the EASYdrive ideally in the control environment of its application.The required optional control variant must be specified for orders.The EASYdrive lasts without external filter measures the EMC class C2 (for 3-phase mains supply), or C1 (for 1-phase mains supply). ! Possible variant selection! Product selection When selecting the frequency converter, make sure that there are 3 variants. First, this includes the devicein the standard version, secondly the device with a membrane keyboard and thirdly the device with an MMI operating unit.The illustrated "frequency converter in standard version" is fully usable and contains a built-in potentiometer,but needs to control a corresponding control panel.For this purpose, one of the following options must be ordered: - External HMI device (MMI with cable and plug)- Interface cable for PC programming- Bluetooth adapter The variant "Frequency inverter with membrane keypad" offers the possibility to directly control the FI,such as Start-stop, left-right-run etc.For parameterization, one of the following options must also be ordered::- External HMI device (MMI with cable and plug)- Interface cable for PC programming- Bluetooth adapter The variant "Frequency converter with MMI operating unit" does not require an optional operating unitIn addition, a display is included in the device cover. The mentioned options can be used if required. Important notesThis drive is a custom-made product. A withdrawal or cancellation of the purchase is excluded!All product photos are non-binding examples!
Worm Gear Motor, Power= 0,75 KW, Speed= 6 to 67 rpm, Degree of protection= IP55, Insulation class= F (155°C), Operating mode= S1, Type of duty= S1- 100%,Hollow shaft= 28mm, Engine Speed= 4 pole, Ratio (i)= 25, Torque= 102 Nm,Service factor (f.s.)= 2 . Terminal box= top (rotatable), Weight= 21 kg, Paint= RAL 5010 (gentian blue),Temperature sensor= 3 x PTC-thermistors, Housing= Aluminum or cast iron, Ball bearings= SKF, C & U or equivalent, Frequency InverterPower= 0.75 KW, Size= A, Input Voltage= 1 x 230V +10% (single phase), Input frequency= 50/60 Hz,Output frequency= 0-400 Hz, EMC filter= C1, Degree of protection= IP65, Dimensions= 233mm x 153mm x 120mm,Mains current (input)= 6.9 A. Ideal control range= 5-60 Hz, below 30 Hz, a forced cooling fan is used for coolingneeded. Product Information The frequency converter optionally offers the possibility of becoming "bus-capable" with the aid of fieldbus modules. With CANopen, EtherCAT, Modbus (already included), Profibus, Profinet and Sercos the EASYdrive offers Compatibility with almost all common interfaces. The customer can choose the relevant bus system for him and integrate the EASYdrive ideally in the control environment of its application.The required optional control variant must be specified for orders.The EASYdrive lasts without external filter measures the EMC class C2 (for 3-phase mains supply), or C1 (for 1-phase mains supply). ! Possible variant selection! Product selection When selecting the frequency converter, make sure that there are 3 variants. First, this includes the devicein the standard version, secondly the device with a membrane keyboard and thirdly the device with an MMI operating unit.The illustrated "frequency converter in standard version" is fully usable and contains a built-in potentiometer,but needs to control a corresponding control panel.For this purpose, one of the following options must be ordered: - External HMI device (MMI with cable and plug)- Interface cable for PC programming- Bluetooth adapter The variant "Frequency inverter with membrane keypad" offers the possibility to directly control the FI,such as Start-stop, left-right-run etc.For parameterization, one of the following options must also be ordered::- External HMI device (MMI with cable and plug)- Interface cable for PC programming- Bluetooth adapter The variant "Frequency converter with MMI operating unit" does not require an optional operating unitIn addition, a display is included in the device cover. The mentioned options can be used if required. Important notesThis drive is a custom-made product. A withdrawal or cancellation of the purchase is excluded!All product photos are non-binding examples!
Worm Gear Motor, Power= 1,5 KW, Speed= 7 to 84 rpm, Degree of protection= IP55, Insulation class= F (155°C), Operating mode= S1, Type of duty= S1- 100%,Hollow shaft= 25mm, Engine Speed= 4 pole, Ratio (i)= 20, Torque= 166 Nm,Service factor (f.s.)= 0,8 . Terminal box= top (rotatable), Weight= 27,2 kg, Paint= RAL 5010 (gentian blue),Temperature sensor= 3 x PTC-thermistors, Housing= Aluminum or cast iron, Ball bearings= SKF, C & U or equivalent, Frequency InverterPower= 1.1 KW, Size= A, Input Voltage= 1 x 230V +10% (single phase), Input frequency= 50/60 Hz,Output frequency= 0-400 Hz, EMC filter= C1, Degree of protection= IP65, Dimensions= 233mm x 153mm x 120mm,Mains current (input)= 9.2 A. Ideal control range= 5-60 Hz, below 30 Hz, a forced cooling fan is used for coolingneeded. Product Information The frequency converter optionally offers the possibility of becoming "bus-capable" with the aid of fieldbus modules. With CANopen, EtherCAT, Modbus (already included), Profibus, Profinet and Sercos the EASYdrive offers Compatibility with almost all common interfaces. The customer can choose the relevant bus system for him and integrate the EASYdrive ideally in the control environment of its application.The required optional control variant must be specified for orders.The EASYdrive lasts without external filter measures the EMC class C2 (for 3-phase mains supply), or C1 (for 1-phase mains supply). ! Possible variant selection! Product selection When selecting the frequency converter, make sure that there are 3 variants. First, this includes the devicein the standard version, secondly the device with a membrane keyboard and thirdly the device with an MMI operating unit.The illustrated "frequency converter in standard version" is fully usable and contains a built-in potentiometer,but needs to control a corresponding control panel.For this purpose, one of the following options must be ordered: - External HMI device (MMI with cable and plug)- Interface cable for PC programming- Bluetooth adapter The variant "Frequency inverter with membrane keypad" offers the possibility to directly control the FI,such as Start-stop, left-right-run etc.For parameterization, one of the following options must also be ordered::- External HMI device (MMI with cable and plug)- Interface cable for PC programming- Bluetooth adapter The variant "Frequency converter with MMI operating unit" does not require an optional operating unitIn addition, a display is included in the device cover. The mentioned options can be used if required. Important notesThis drive is a custom-made product. A withdrawal or cancellation of the purchase is excluded!All product photos are non-binding examples!
Worm Gear Motor, Power= 1,5 KW, Speed= 14 to 168 rpm, Degree of protection= IP55, Insulation class= F (155°C), Operating mode= S1, Type of duty= S1- 100%,Hollow shaft= 25mm, Engine Speed= 4 pole, Ratio (i)= 10, Torque= 89 Nm,Service factor (f.s.)= 1,5 . Terminal box= top (rotatable), Weight= 27,2 kg, Paint= RAL 5010 (gentian blue),Temperature sensor= 3 x PTC-thermistors, Housing= Aluminum or cast iron, Ball bearings= SKF, C & U or equivalent, Frequency InverterPower= 1.1 KW, Size= A, Input Voltage= 1 x 230V +10% (single phase), Input frequency= 50/60 Hz,Output frequency= 0-400 Hz, EMC filter= C1, Degree of protection= IP65, Dimensions= 233mm x 153mm x 120mm,Mains current (input)= 9.2 A. Ideal control range= 5-60 Hz, below 30 Hz, a forced cooling fan is used for coolingneeded. Product Information The frequency converter optionally offers the possibility of becoming "bus-capable" with the aid of fieldbus modules. With CANopen, EtherCAT, Modbus (already included), Profibus, Profinet and Sercos the EASYdrive offers Compatibility with almost all common interfaces. The customer can choose the relevant bus system for him and integrate the EASYdrive ideally in the control environment of its application.The required optional control variant must be specified for orders.The EASYdrive lasts without external filter measures the EMC class C2 (for 3-phase mains supply), or C1 (for 1-phase mains supply). ! Possible variant selection! Product selection When selecting the frequency converter, make sure that there are 3 variants. First, this includes the devicein the standard version, secondly the device with a membrane keyboard and thirdly the device with an MMI operating unit.The illustrated "frequency converter in standard version" is fully usable and contains a built-in potentiometer,but needs to control a corresponding control panel.For this purpose, one of the following options must be ordered: - External HMI device (MMI with cable and plug)- Interface cable for PC programming- Bluetooth adapter The variant "Frequency inverter with membrane keypad" offers the possibility to directly control the FI,such as Start-stop, left-right-run etc.For parameterization, one of the following options must also be ordered::- External HMI device (MMI with cable and plug)- Interface cable for PC programming- Bluetooth adapter The variant "Frequency converter with MMI operating unit" does not require an optional operating unitIn addition, a display is included in the device cover. The mentioned options can be used if required. Important notesThis drive is a custom-made product. A withdrawal or cancellation of the purchase is excluded!All product photos are non-binding examples!
Worm Gear Motor, Power= 1,5 KW, Speed= 9 to 110 rpm, Degree of protection= IP55, Insulation class= F (155°C), Operating mode= S1, Type of duty= S1- 100%,Hollow shaft= 25mm, Engine Speed= 4 pole, Ratio (i)= 15, Torque= 127 Nm,Service factor (f.s.)= 1,1 . Terminal box= top (rotatable), Weight= 27,2 kg, Paint= RAL 5010 (gentian blue),Temperature sensor= 3 x PTC-thermistors, Housing= Aluminum or cast iron, Ball bearings= SKF, C & U or equivalent, Frequency InverterPower= 1.1 KW, Size= A, Input Voltage= 1 x 230V +10% (single phase), Input frequency= 50/60 Hz,Output frequency= 0-400 Hz, EMC filter= C1, Degree of protection= IP65, Dimensions= 233mm x 153mm x 120mm,Mains current (input)= 9.2 A. Ideal control range= 5-60 Hz, below 30 Hz, a forced cooling fan is used for coolingneeded. Product Information The frequency converter optionally offers the possibility of becoming "bus-capable" with the aid of fieldbus modules. With CANopen, EtherCAT, Modbus (already included), Profibus, Profinet and Sercos the EASYdrive offers Compatibility with almost all common interfaces. The customer can choose the relevant bus system for him and integrate the EASYdrive ideally in the control environment of its application.The required optional control variant must be specified for orders.The EASYdrive lasts without external filter measures the EMC class C2 (for 3-phase mains supply), or C1 (for 1-phase mains supply). ! Possible variant selection! Product selection When selecting the frequency converter, make sure that there are 3 variants. First, this includes the devicein the standard version, secondly the device with a membrane keyboard and thirdly the device with an MMI operating unit.The illustrated "frequency converter in standard version" is fully usable and contains a built-in potentiometer,but needs to control a corresponding control panel.For this purpose, one of the following options must be ordered: - External HMI device (MMI with cable and plug)- Interface cable for PC programming- Bluetooth adapter The variant "Frequency inverter with membrane keypad" offers the possibility to directly control the FI,such as Start-stop, left-right-run etc.For parameterization, one of the following options must also be ordered::- External HMI device (MMI with cable and plug)- Interface cable for PC programming- Bluetooth adapter The variant "Frequency converter with MMI operating unit" does not require an optional operating unitIn addition, a display is included in the device cover. The mentioned options can be used if required. Important notesThis drive is a custom-made product. A withdrawal or cancellation of the purchase is excluded!All product photos are non-binding examples!
Worm Gear Motor, Power= 1,1 KW, Speed= 6 to 67 rpmDegree of protection= IP55, Insulation class= F (155°C), Operating mode= S1, Type of duty= S1- 100%,Hollow shaft= 28mm, Engine Speed= 4 pole, Ratio (i)= 25, Torque= 150 Nm,Service factor (f.s.)= 1,3 . Terminal box= top (rotatable), Weight= 26 kg, Paint= RAL 5010 (gentian blue),Temperature sensor= 3 x PTC-thermistors, Housing= Aluminum or cast iron, Ball bearings= SKF, C & U or equivalent, Frequency InverterPower= 1.1 KW, Size= A, Input Voltage= 1 x 230V +10% (single phase), Input frequency= 50/60 Hz,Output frequency= 0-400 Hz, EMC filter= C1, Degree of protection= IP65, Dimensions= 233mm x 153mm x 120mm,Mains current (input)= 9.2 A. Ideal control range= 5-60 Hz, below 30 Hz, a forced cooling fan is used for coolingneeded. Product Information The frequency converter optionally offers the possibility of becoming "bus-capable" with the aid of fieldbus modules. With CANopen, EtherCAT, Modbus (already included), Profibus, Profinet and Sercos the EASYdrive offers Compatibility with almost all common interfaces. The customer can choose the relevant bus system for him and integrate the EASYdrive ideally in the control environment of its application.The required optional control variant must be specified for orders.The EASYdrive lasts without external filter measures the EMC class C2 (for 3-phase mains supply), or C1 (for 1-phase mains supply). ! Possible variant selection! Product selection When selecting the frequency converter, make sure that there are 3 variants. First, this includes the devicein the standard version, secondly the device with a membrane keyboard and thirdly the device with an MMI operating unit.The illustrated "frequency converter in standard version" is fully usable and contains a built-in potentiometer,but needs to control a corresponding control panel.For this purpose, one of the following options must be ordered: - External HMI device (MMI with cable and plug)- Interface cable for PC programming- Bluetooth adapter The variant "Frequency inverter with membrane keypad" offers the possibility to directly control the FI,such as Start-stop, left-right-run etc.For parameterization, one of the following options must also be ordered::- External HMI device (MMI with cable and plug)- Interface cable for PC programming- Bluetooth adapter The variant "Frequency converter with MMI operating unit" does not require an optional operating unitIn addition, a display is included in the device cover. The mentioned options can be used if required. Important notesThis drive is a custom-made product. A withdrawal or cancellation of the purchase is excluded!All product photos are non-binding examples!
Worm Gear Motor, Power= 1,1 KW, Speed= 4 to 42 rpm, Degree of protection= IP55, Insulation class= F (155°C), Operating mode= S1, Type of duty= S1- 100%,Hollow shaft= 28mm, Engine Speed= 4 pole, Ratio (i)= 40, Torque= 216 Nm,Service factor (f.s.)= 1 . Terminal box= top (rotatable), Weight= 26 kg, Paint= RAL 5010 (gentian blue),Temperature sensor= 3 x PTC-thermistors, Housing= Aluminum or cast iron, Ball bearings= SKF, C & U or equivalent, Frequency InverterPower= 1.1 KW, Size= A, Input Voltage= 1 x 230V +10% (single phase), Input frequency= 50/60 Hz,Output frequency= 0-400 Hz, EMC filter= C1, Degree of protection= IP65, Dimensions= 233mm x 153mm x 120mm,Mains current (input)= 9.2 A. Ideal control range= 5-60 Hz, below 30 Hz, a forced cooling fan is used for coolingneeded. Product Information The frequency converter optionally offers the possibility of becoming "bus-capable" with the aid of fieldbus modules. With CANopen, EtherCAT, Modbus (already included), Profibus, Profinet and Sercos the EASYdrive offers Compatibility with almost all common interfaces. The customer can choose the relevant bus system for him and integrate the EASYdrive ideally in the control environment of its application.The required optional control variant must be specified for orders.The EASYdrive lasts without external filter measures the EMC class C2 (for 3-phase mains supply), or C1 (for 1-phase mains supply). ! Possible variant selection! Product selection When selecting the frequency converter, make sure that there are 3 variants. First, this includes the devicein the standard version, secondly the device with a membrane keyboard and thirdly the device with an MMI operating unit.The illustrated "frequency converter in standard version" is fully usable and contains a built-in potentiometer,but needs to control a corresponding control panel.For this purpose, one of the following options must be ordered: - External HMI device (MMI with cable and plug)- Interface cable for PC programming- Bluetooth adapter The variant "Frequency inverter with membrane keypad" offers the possibility to directly control the FI,such as Start-stop, left-right-run etc.For parameterization, one of the following options must also be ordered::- External HMI device (MMI with cable and plug)- Interface cable for PC programming- Bluetooth adapter The variant "Frequency converter with MMI operating unit" does not require an optional operating unitIn addition, a display is included in the device cover. The mentioned options can be used if required. Important notesThis drive is a custom-made product. A withdrawal or cancellation of the purchase is excluded!All product photos are non-binding examples!
Worm Gear Motor, Power= 1,1 KW, Speed= 9 to 110 rpm, Degree of protection= IP55, Insulation class= F (155°C), Operating mode= S1, Type of duty= S1- 100%,Hollow shaft= 28mm, Engine Speed= 4 pole, Ratio (i)= 15, Torque= 96 Nm,Service factor (f.s.)= 2,1 . Terminal box= top (rotatable), Weight= 26 kg, Paint= RAL 5010 (gentian blue),Temperature sensor= 3 x PTC-thermistors, Housing= Aluminum or cast iron, Ball bearings= SKF, C & U or equivalent, Frequency InverterPower= 1.1 KW, Size= A, Input Voltage= 3 x 400V + 10% (three-phase), Input frequency= 50/60 Hz,Output frequency= 0-400 Hz, EMC filter= C2, Degree of protection= IP65, Dimensions= 233mm x 153mm x 120mm,Mains current (input)= 2.6 A. Ideal control range= 5-60 Hz, below 30 Hz, a forced cooling fan is used for coolingneeded. Product Information The frequency converter optionally offers the possibility of becoming "bus-capable" with the aid of fieldbus modules. With CANopen, EtherCAT, Modbus (already included), Profibus, Profinet and Sercos the EASYdrive offers Compatibility with almost all common interfaces. The customer can choose the relevant bus system for him and integrate the EASYdrive ideally in the control environment of its application.The required optional control variant must be specified for orders.The EASYdrive lasts without external filter measures the EMC class C2 (for 3-phase mains supply), or C1 (for 1-phase mains supply). ! Possible variant selection! Product selection When selecting the frequency converter, make sure that there are 3 variants. First, this includes the devicein the standard version, secondly the device with a membrane keyboard and thirdly the device with an MMI operating unit.The illustrated "frequency converter in standard version" is fully usable and contains a built-in potentiometer,but needs to control a corresponding control panel.For this purpose, one of the following options must be ordered: - External HMI device (MMI with cable and plug)- Interface cable for PC programming- Bluetooth adapter The variant "Frequency inverter with membrane keypad" offers the possibility to directly control the FI,such as Start-stop, left-right-run etc.For parameterization, one of the following options must also be ordered:: - External HMI device (MMI with cable and plug)- Interface cable for PC programming- Bluetooth adapter The variant "Frequency converter with MMI operating unit" does not require an optional operating unitIn addition, a display is included in the device cover. The mentioned options can be used if required. Important notesThis drive is a custom-made product. A withdrawal or cancellation of the purchase is excluded!All product photos are non-binding examples!
Worm Gear Motor, Power= 1,1 KW, Speed= 7 to 84 rpm, Degree of protection= IP55, Insulation class= F (155°C), Operating mode= S1, Type of duty= S1- 100%,Hollow shaft= 28mm, Engine Speed= 4 pole, Ratio (i)= 20, Torque= 123 Nm,Service factor (f.s.)= 1,7 . Terminal box= top (rotatable), Weight= 26 kg, Paint= RAL 5010 (gentian blue),Temperature sensor= 3 x PTC-thermistors, Housing= Aluminum or cast iron, Ball bearings= SKF, C & U or equivalent, Frequency InverterPower= 1.1 KW, Size= A, Input Voltage= 3 x 400V + 10% (three-phase), Input frequency= 50/60 Hz,Output frequency= 0-400 Hz, EMC filter= C2, Degree of protection= IP65, Dimensions= 233mm x 153mm x 120mm,Mains current (input)= 2.6 A. Ideal control range= 5-60 Hz, below 30 Hz, a forced cooling fan is used for coolingneeded. Product Information The frequency converter optionally offers the possibility of becoming "bus-capable" with the aid of fieldbus modules. With CANopen, EtherCAT, Modbus (already included), Profibus, Profinet and Sercos the EASYdrive offers Compatibility with almost all common interfaces. The customer can choose the relevant bus system for him and integrate the EASYdrive ideally in the control environment of its application.The required optional control variant must be specified for orders.The EASYdrive lasts without external filter measures the EMC class C2 (for 3-phase mains supply), or C1 (for 1-phase mains supply). ! Possible variant selection! Product selection When selecting the frequency converter, make sure that there are 3 variants. First, this includes the devicein the standard version, secondly the device with a membrane keyboard and thirdly the device with an MMI operating unit.The illustrated "frequency converter in standard version" is fully usable and contains a built-in potentiometer,but needs to control a corresponding control panel.For this purpose, one of the following options must be ordered: - External HMI device (MMI with cable and plug)- Interface cable for PC programming- Bluetooth adapter The variant "Frequency inverter with membrane keypad" offers the possibility to directly control the FI,such as Start-stop, left-right-run etc.For parameterization, one of the following options must also be ordered:: - External HMI device (MMI with cable and plug)- Interface cable for PC programming- Bluetooth adapter The variant "Frequency converter with MMI operating unit" does not require an optional operating unitIn addition, a display is included in the device cover. The mentioned options can be used if required. Important notesThis drive is a custom-made product. A withdrawal or cancellation of the purchase is excluded!All product photos are non-binding examples!
Worm Gear Motor, Power= 1,1 KW, Speed= 6 to 67 rpm, Degree of protection= IP55, Insulation class= F (155°C), Operating mode= S1, Type of duty= S1- 100%,Hollow shaft= 28mm, Engine Speed= 4 pole, Ratio (i)= 25, Torque= 150 Nm,Service factor (f.s.)= 1,3 . Terminal box= top (rotatable), Weight= 26 kg, Paint= RAL 5010 (gentian blue),Temperature sensor= 3 x PTC-thermistors, Housing= Aluminum or cast iron, Ball bearings= SKF, C & U or equivalent, Frequency InverterPower= 1.1 KW, Size= A, Input Voltage= 3 x 400V + 10% (three-phase), Input frequency= 50/60 Hz,Output frequency= 0-400 Hz, EMC filter= C2, Degree of protection= IP65, Dimensions= 233mm x 153mm x 120mm,Mains current (input)= 2.6 A. Ideal control range= 5-60 Hz, below 30 Hz, a forced cooling fan is used for coolingneeded. Product Information The frequency converter optionally offers the possibility of becoming "bus-capable" with the aid of fieldbus modules. With CANopen, EtherCAT, Modbus (already included), Profibus, Profinet and Sercos the EASYdrive offers Compatibility with almost all common interfaces. The customer can choose the relevant bus system for him and integrate the EASYdrive ideally in the control environment of its application.The required optional control variant must be specified for orders.The EASYdrive lasts without external filter measures the EMC class C2 (for 3-phase mains supply), or C1 (for 1-phase mains supply). ! Possible variant selection! Product selection When selecting the frequency converter, make sure that there are 3 variants. First, this includes the devicein the standard version, secondly the device with a membrane keyboard and thirdly the device with an MMI operating unit.The illustrated "frequency converter in standard version" is fully usable and contains a built-in potentiometer,but needs to control a corresponding control panel.For this purpose, one of the following options must be ordered: - External HMI device (MMI with cable and plug)- Interface cable for PC programming- Bluetooth adapter The variant "Frequency inverter with membrane keypad" offers the possibility to directly control the FI,such as Start-stop, left-right-run etc.For parameterization, one of the following options must also be ordered:: - External HMI device (MMI with cable and plug)- Interface cable for PC programming- Bluetooth adapter The variant "Frequency converter with MMI operating unit" does not require an optional operating unitIn addition, a display is included in the device cover. The mentioned options can be used if required. Important notesThis drive is a custom-made product. A withdrawal or cancellation of the purchase is excluded!All product photos are non-binding examples!
Worm Gear Motor, Power= 1,1 KW, Speed= 4 to 42 rpm, Degree of protection= IP55, Insulation class= F (155°C), Operating mode= S1, Type of duty= S1- 100%,Hollow shaft= 28mm, Engine Speed= 4 pole, Ratio (i)= 40, Torque= 216 Nm,Service factor (f.s.)= 1 . Terminal box= top (rotatable), Weight= 26 kg, Paint= RAL 5010 (gentian blue),Temperature sensor= 3 x PTC-thermistors, Housing= Aluminum or cast iron, Ball bearings= SKF, C & U or equivalent, Frequency InverterPower= 1.1 KW, Size= A, Input Voltage= 3 x 400V + 10% (three-phase), Input frequency= 50/60 Hz,Output frequency= 0-400 Hz, EMC filter= C2, Degree of protection= IP65, Dimensions= 233mm x 153mm x 120mm,Mains current (input)= 2.6 A. Ideal control range= 5-60 Hz, below 30 Hz, a forced cooling fan is used for coolingneeded. Product Information The frequency converter optionally offers the possibility of becoming "bus-capable" with the aid of fieldbus modules. With CANopen, EtherCAT, Modbus (already included), Profibus, Profinet and Sercos the EASYdrive offers Compatibility with almost all common interfaces. The customer can choose the relevant bus system for him and integrate the EASYdrive ideally in the control environment of its application.The required optional control variant must be specified for orders.The EASYdrive lasts without external filter measures the EMC class C2 (for 3-phase mains supply), or C1 (for 1-phase mains supply). ! Possible variant selection! Product selection When selecting the frequency converter, make sure that there are 3 variants. First, this includes the devicein the standard version, secondly the device with a membrane keyboard and thirdly the device with an MMI operating unit.The illustrated "frequency converter in standard version" is fully usable and contains a built-in potentiometer,but needs to control a corresponding control panel.For this purpose, one of the following options must be ordered: - External HMI device (MMI with cable and plug)- Interface cable for PC programming- Bluetooth adapter The variant "Frequency inverter with membrane keypad" offers the possibility to directly control the FI,such as Start-stop, left-right-run etc.For parameterization, one of the following options must also be ordered:: - External HMI device (MMI with cable and plug)- Interface cable for PC programming- Bluetooth adapter The variant "Frequency converter with MMI operating unit" does not require an optional operating unitIn addition, a display is included in the device cover. The mentioned options can be used if required. Important notesThis drive is a custom-made product. A withdrawal or cancellation of the purchase is excluded!All product photos are non-binding examples!
Worm Gear Motor, Power= 1,1 KW, Speed= 7 to 84 rpmDegree of protection= IP55, Insulation class= F (155°C), Operating mode= S1, Type of duty= S1- 100%,Hollow shaft= 28mm, Engine Speed= 4 pole, Ratio (i)= 20, Torque= 123 Nm,Service factor (f.s.)= 1,7 . Terminal box= top (rotatable), Weight= 26 kg, Paint= RAL 5010 (gentian blue),Temperature sensor= 3 x PTC-thermistors, Housing= Aluminum or cast iron, Ball bearings= SKF, C & U or equivalent, Frequency InverterPower= 1.1 KW, Size= A, Input Voltage= 1 x 230V +10% (single phase), Input frequency= 50/60 Hz,Output frequency= 0-400 Hz, EMC filter= C1, Degree of protection= IP65, Dimensions= 233mm x 153mm x 120mm,Mains current (input)= 9.2 A. Ideal control range= 5-60 Hz, below 30 Hz, a forced cooling fan is used for coolingneeded. Product Information The frequency converter optionally offers the possibility of becoming "bus-capable" with the aid of fieldbus modules. With CANopen, EtherCAT, Modbus (already included), Profibus, Profinet and Sercos the EASYdrive offers Compatibility with almost all common interfaces. The customer can choose the relevant bus system for him and integrate the EASYdrive ideally in the control environment of its application.The required optional control variant must be specified for orders.The EASYdrive lasts without external filter measures the EMC class C2 (for 3-phase mains supply), or C1 (for 1-phase mains supply). ! Possible variant selection! Product selection When selecting the frequency converter, make sure that there are 3 variants. First, this includes the devicein the standard version, secondly the device with a membrane keyboard and thirdly the device with an MMI operating unit.The illustrated "frequency converter in standard version" is fully usable and contains a built-in potentiometer,but needs to control a corresponding control panel.For this purpose, one of the following options must be ordered: - External HMI device (MMI with cable and plug)- Interface cable for PC programming- Bluetooth adapter The variant "Frequency inverter with membrane keypad" offers the possibility to directly control the FI,such as Start-stop, left-right-run etc.For parameterization, one of the following options must also be ordered::- External HMI device (MMI with cable and plug)- Interface cable for PC programming- Bluetooth adapter The variant "Frequency converter with MMI operating unit" does not require an optional operating unitIn addition, a display is included in the device cover. The mentioned options can be used if required. Important notesThis drive is a custom-made product. A withdrawal or cancellation of the purchase is excluded!All product photos are non-binding examples!
Worm Gear Motor, Power= 1,1 KW, Speed= 9 to 110 rpm, Degree of protection= IP55, Insulation class= F (155°C), Operating mode= S1, Type of duty= S1- 100%,Hollow shaft= 28mm, Engine Speed= 4 pole, Ratio (i)= 15, Torque= 96 Nm,Service factor (f.s.)= 2,1 . Terminal box= top (rotatable), Weight= 26 kg, Paint= RAL 5010 (gentian blue),Temperature sensor= 3 x PTC-thermistors, Housing= Aluminum or cast iron, Ball bearings= SKF, C & U or equivalent, Frequency InverterPower= 1.1 KW, Size= A, Input Voltage= 1 x 230V +10% (single phase), Input frequency= 50/60 Hz,Output frequency= 0-400 Hz, EMC filter= C1, Degree of protection= IP65, Dimensions= 233mm x 153mm x 120mm,Mains current (input)= 9.2 A. Ideal control range= 5-60 Hz, below 30 Hz, a forced cooling fan is used for coolingneeded. Product Information The frequency converter optionally offers the possibility of becoming "bus-capable" with the aid of fieldbus modules. With CANopen, EtherCAT, Modbus (already included), Profibus, Profinet and Sercos the EASYdrive offers Compatibility with almost all common interfaces. The customer can choose the relevant bus system for him and integrate the EASYdrive ideally in the control environment of its application.The required optional control variant must be specified for orders.The EASYdrive lasts without external filter measures the EMC class C2 (for 3-phase mains supply), or C1 (for 1-phase mains supply). ! Possible variant selection! Product selection When selecting the frequency converter, make sure that there are 3 variants. First, this includes the devicein the standard version, secondly the device with a membrane keyboard and thirdly the device with an MMI operating unit.The illustrated "frequency converter in standard version" is fully usable and contains a built-in potentiometer,but needs to control a corresponding control panel.For this purpose, one of the following options must be ordered: - External HMI device (MMI with cable and plug)- Interface cable for PC programming- Bluetooth adapter The variant "Frequency inverter with membrane keypad" offers the possibility to directly control the FI,such as Start-stop, left-right-run etc.For parameterization, one of the following options must also be ordered::- External HMI device (MMI with cable and plug)- Interface cable for PC programming- Bluetooth adapter The variant "Frequency converter with MMI operating unit" does not require an optional operating unitIn addition, a display is included in the device cover. The mentioned options can be used if required. Important notesThis drive is a custom-made product. A withdrawal or cancellation of the purchase is excluded!All product photos are non-binding examples!
Worm Gear Motor, Power= 0,55 KW, Speed= 2 to 16 rpm, Degree of protection= IP55, Insulation class= F (155°C), Operating mode= S1, Type of duty= S1- 100%,Hollow shaft= 35mm, Engine Speed= 4 pole, Ratio (i)= 100, Torque= 221 Nm,Service factor (f.s.)= 1,2 . Terminal box= top (rotatable), Weight= 22 kg, Paint= RAL 5010 (gentian blue),Temperature sensor= 3 x PTC-thermistors, Housing= Aluminum or cast iron, Ball bearings= SKF, C & U or equivalent, Frequency InverterPower= 0.55 KW, Size= A, Input Voltage= 3 x 400V + 10% (three-phase), Input frequency= 50/60 Hz,Output frequency= 0-400 Hz, EMC filter= C2, Degree of protection= IP65, 233mm x 153mm x 120mm,Mains current (input)= 1.4 A. Ideal control range= 5-60 Hz, below 30 Hz, a forced cooling fan is used for coolingneeded. Product Information The frequency converter optionally offers the possibility of becoming "bus-capable" with the aid of fieldbus modules. With CANopen, EtherCAT, Modbus (already included), Profibus, Profinet and Sercos the EASYdrive offers Compatibility with almost all common interfaces. The customer can choose the relevant bus system for him and integrate the EASYdrive ideally in the control environment of its application.The required optional control variant must be specified for orders.The EASYdrive lasts without external filter measures the EMC class C2 (for 3-phase mains supply), or C1 (for 1-phase mains supply). ! Possible variant selection! Product selection When selecting the frequency converter, make sure that there are 3 variants. First, this includes the devicein the standard version, secondly the device with a membrane keyboard and thirdly the device with an MMI operating unit.The illustrated "frequency converter in standard version" is fully usable and contains a built-in potentiometer,but needs to control a corresponding control panel.For this purpose, one of the following options must be ordered: - External HMI device (MMI with cable and plug)- Interface cable for PC programming- Bluetooth adapter The variant "Frequency inverter with membrane keypad" offers the possibility to directly control the FI,such as Start-stop, left-right-run etc.For parameterization, one of the following options must also be ordered:: - External HMI device (MMI with cable and plug)- Interface cable for PC programming- Bluetooth adapter The variant "Frequency converter with MMI operating unit" does not require an optional operating unitIn addition, a display is included in the device cover. The mentioned options can be used if required. Important notesThis drive is a custom-made product. A withdrawal or cancellation of the purchase is excluded!All product photos are non-binding examples!
Worm Gear Motor, Power= 0,55 KW, Speed= 2 to 16 rpm, Degree of protection= IP55, Insulation class= F (155°C), Operating mode= S1, Type of duty= S1- 100%,Hollow shaft= 35mm, Engine Speed= 4 pole, Ratio (i)= 100, Torque= 221 Nm,Service factor (f.s.)= 1,2 . Terminal box= top (rotatable), Weight= 22 kg, Paint= RAL 5010 (gentian blue),Temperature sensor= 3 x PTC-thermistors, Housing= Aluminum or cast iron, Ball bearings= SKF, C & U or equivalent, Frequency InverterPower= 0.55 KW, Size= A, Input Voltage= 1 x 230V +10% (single phase), Input frequency= 50/60 Hz,Output frequency= 0-400 Hz, EMC filter= C1, Degree of protection= IP65, Dimensions= 233mm x 153mm x 120mm,Mains current (input)= 5.6 A. Ideal control range= 5-60 Hz, below 30 Hz, a forced cooling fan is used for coolingneeded. Product Information The frequency converter optionally offers the possibility of becoming "bus-capable" with the aid of fieldbus modules. With CANopen, EtherCAT, Modbus (already included), Profibus, Profinet and Sercos the EASYdrive offers Compatibility with almost all common interfaces. The customer can choose the relevant bus system for him and integrate the EASYdrive ideally in the control environment of its application.The required optional control variant must be specified for orders.The EASYdrive lasts without external filter measures the EMC class C2 (for 3-phase mains supply), or C1 (for 1-phase mains supply). ! Possible variant selection! Product selection When selecting the frequency converter, make sure that there are 3 variants. First, this includes the devicein the standard version, secondly the device with a membrane keyboard and thirdly the device with an MMI operating unit.The illustrated "frequency converter in standard version" is fully usable and contains a built-in potentiometer,but needs to control a corresponding control panel.For this purpose, one of the following options must be ordered: - External HMI device (MMI with cable and plug)- Interface cable for PC programming- Bluetooth adapter The variant "Frequency inverter with membrane keypad" offers the possibility to directly control the FI,such as Start-stop, left-right-run etc.For parameterization, one of the following options must also be ordered::- External HMI device (MMI with cable and plug)- Interface cable for PC programming- Bluetooth adapter The variant "Frequency converter with MMI operating unit" does not require an optional operating unitIn addition, a display is included in the device cover. The mentioned options can be used if required. Important notesThis drive is a custom-made product. A withdrawal or cancellation of the purchase is excluded!All product photos are non-binding examples!
Worm Gear Motor, Power= 0,55 KW, Speed= 2 to 16 rpm, Degree of protection= IP55, Insulation class= F (155°C), Operating mode= S1, Type of duty= S1- 100%,Hollow shaft= 42mm, Mounting position= M1-M6. Engine Speed= 4 pole, Ratio (i)= 100, Torque= 236 Nm,Service factor (f.s.)= 2 . Terminal box= top (rotatable), Weight= 44 kg , Paint= RAL 5010 (gentian blue),Temperature sensor= 3 x PTC-thermistors, Housing= Aluminum or cast iron, Ball bearings= SKF, C & U or equivalent, When ordering, please select the desired mounting position and design! Frequency inverterPower= 0.55 KW, Size= alpha, Input Voltage= 1 x 230V +10% (single phase), Input frequency= 50/60 Hz,Output frequency= 0-400 Hz, EMC filter= C2, Degree of protection= IP65, Dimensions= 187mm x 126mm x 80mm,Mains current (input)= 5.8 A. Ideal control range= 5-60 Hz, below 30 Hz, a forced cooling fan is used for coolingneeded. Product Information The frequency converter optionally offers the possibility of becoming "bus-capable" with the aid of fieldbus modules. With Modbus (already included) and CANopen, the EASYdrive alpha provides compatibility with control environments.The customer can choose the relevant bus system for him and integrate the EASYdrive ideally in the controlenvironment of its application.The required optional control variant must be specified for orders.The EASYdrive lastswithout external filter measures the EMC class C2 (for 3-phase mains supply), or C1 (for 1-phase mains supply). ! Possible variant selection! Product selection When selecting the frequency converter, make sure that there are 2 variants. First, this includes the devicein the standard version, secondly the device with a membrane keyboard. Both versions include a potentiometerinstalled on the side.The illustrated "frequency converter in standard version" is fully usable, but needs to control a corresponding control panel.For this purpose, one of the following options must be ordered:: - External HMI device (MMI with cable and plug)- Interface cable for PC programming- Bluetooth adapter The variant "Frequency inverter with membrane keypad" offers the possibility to directly control the FI,such as Start-stop, left-right-run etc.For parameterization, one of the following options must also be ordered:: - External HMI device (MMI with cable and plug)- Interface cable for PC programming- Bluetooth adapter Important notesThis drive is a custom-made product. A withdrawal or cancellation of the purchase is excluded!All product photos are non-binding examples!
Worm Gear Motor, Power= 1,5 KW, Speed= 9 to 110 rpm, Degree of protection= IP55, Insulation class= F (155°C), Operating mode= S1, Type of duty= S1- 100%,Hollow shaft= 28mm, Engine Speed= 4 pole, Ratio (i)= 15, Torque= 130 Nm,Service factor (f.s.)= 1,5 . Terminal box= top (rotatable), Weight= 30 kg, Paint= RAL 5010 (gentian blue),Temperature sensor= 3 x PTC-thermistors, Housing= Aluminum or cast iron, Ball bearings= SKF, C & U or equivalent, Frequency InverterPower= 1.5 KW, Size= A, Input Voltage= 3 x 400V + 10% (three-phase), Input frequency= 50/60 Hz,Output frequency= 0-400 Hz, EMC filter= C2, Degree of protection= IP65, Dimensions= 233mm x 153mm x 120mm,Mains current (input)= 3.3 A. Ideal control range= 5-60 Hz, below 30 Hz, a forced cooling fan is used for coolingneeded. Product Information The frequency converter optionally offers the possibility of becoming "bus-capable" with the aid of fieldbus modules. With CANopen, EtherCAT, Modbus (already included), Profibus, Profinet and Sercos the EASYdrive offers Compatibility with almost all common interfaces. The customer can choose the relevant bus system for him and integrate the EASYdrive ideally in the control environment of its application.The required optional control variant must be specified for orders.The EASYdrive lasts without external filter measures the EMC class C2 (for 3-phase mains supply), or C1 (for 1-phase mains supply). ! Possible variant selection! Product selection When selecting the frequency converter, make sure that there are 3 variants. First, this includes the devicein the standard version, secondly the device with a membrane keyboard and thirdly the device with an MMI operating unit.The illustrated "frequency converter in standard version" is fully usable and contains a built-in potentiometer,but needs to control a corresponding control panel.For this purpose, one of the following options must be ordered: - External HMI device (MMI with cable and plug)- Interface cable for PC programming- Bluetooth adapter The variant "Frequency inverter with membrane keypad" offers the possibility to directly control the FI,such as Start-stop, left-right-run etc.For parameterization, one of the following options must also be ordered:: - External HMI device (MMI with cable and plug)- Interface cable for PC programming- Bluetooth adapter The variant "Frequency converter with MMI operating unit" does not require an optional operating unitIn addition, a display is included in the device cover. The mentioned options can be used if required. Important notesThis drive is a custom-made product. A withdrawal or cancellation of the purchase is excluded!All product photos are non-binding examples!
Worm geared motors with frequency inverter
Thanks to our many years of experience in the field of drive technology, we are the ideal partner when it comes to the use of worm geared motors with integrated frequency inverters. Top quality, a competent team and a competitive price are our top priorities. If you cannot find the right drive for your application, please send us an enquiry by email or simply contact us directly by phone.
Size and performance
The electrically variable worm geared motors are made from an aluminium or grey cast iron housing and are available in the sizes CMRV, 30, 40, 50, 63, 75, 80, 90, 100, 110, 125, 130 and 150. The combination of worm gearbox, frequency inverter and three-phase motor is available with an output of 0.18kW, 0.25kW, 0.37kW, 0.55kW, 0.75kW, 1.1kW, 1.5kW, 2.2kW, 3.0kW, 4.0kW, 5.5kW, 7.5kW and 11kW.
Shaft diameters and torques
The worm gearboxes are available with the following hollow shafts: 14 mm, 18 mm, 20 mm, 25 mm, 28 mm, 30 mm, 35 mm, 40 mm, 45 mm and 50 mm. The torque output depends on the motor power, the efficiency and the drive speed, among other factors. Taking these points into account, we supply worm gearboxes in a range of 10 - 2000 Nm.
Frequency inverter - Installation
The EASYdrive frequency inverter is mounted on the motor terminal box using an adapter plate and can be mounted in 90° steps by rotating the motor. The JS-Technik worm geared motor can be installed in almost any required position. The installation positions are labelled M1, M2, M3, M4, M5, M6.
Frequently required accessories
As the variable speed drive unit is often operated below 35 Hertz, the motor must be protected against overheating with an external forced cooling fan.
Furthermore, a high level of self-locking of the gear unit is often necessary. As this is often too low in worm gearboxes, a three-phase motor with brake is required.
Naturally, we supply and install the forced cooling fan and the motor brake for the required worm geared motor.
The special frequency inverter
The frequency inverter offers the option of becoming "bus-compatible" with the help of fieldbus modules. With CANopen, EtherCAT, Modbus (already included), Profibus, Profinet and Sercos, the EASYdrive offers compatibility with almost all common control environments. Customers can select the bus system that is relevant to them and thus integrate the EASYdrive perfectly into the control environment of their application. The required optional control variant must be specified when ordering. The EASYdrive drive controllers are CE, UL and CSA certified. Without external filter measures, the EASYdrive fulfilseMC class C2 (for 3-phase mains supply) or C1 (for 1-phase mains supply) without external filter measures.
sEO: Worm gearbox with frequency inverter motor