Worm Gear Motor, Power= 1,1 KW, Speed= 2 to 16 rpm, Degree of protection= IP55, Insulation class= F (155°C), Operating mode= S1, Type of duty= S1- 100%,Hollow shaft= 42mm, Mounting position= M1-M6. Engine Speed= 4 pole, Ratio (i)= 100, Torque= 473 Nm,Service factor (f.s.)= 1 . Terminal box= top (rotatable), Weight= 52 kg , Paint= RAL 5010 (gentian blue),Temperature sensor= 3 x PTC-thermistors, Housing= Aluminum or cast iron, Ball bearings= SKF, C & U or equivalent, When ordering, please select the desired mounting position and design! Frequency InverterPower= 1.1 KW, Size= A, Input Voltage= 1 x 230V +10% (single phase), Input frequency= 50/60 Hz,Output frequency= 0-400 Hz, EMC filter= C1, Degree of protection= IP65, Dimensions= 233mm x 153mm x 120mm,Mains current (input)= 9.2 A. Ideal control range= 5-60 Hz, below 30 Hz, a forced cooling fan is used for coolingneeded.  Product Information The frequency converter optionally offers the possibility of becoming "bus-capable" with the aid of fieldbus modules. With CANopen, EtherCAT, Modbus (already included), Profibus, Profinet and Sercos the EASYdrive offers Compatibility with almost all common interfaces. The customer can choose the relevant bus system for him and integrate the EASYdrive ideally in the control environment of its application.The required optional control variant must be specified for orders.The EASYdrive lasts without external filter measures the EMC class C2 (for 3-phase mains supply), or C1 (for 1-phase mains supply).   ! Possible variant selection!               Product selection When selecting the frequency converter, make sure that there are 3 variants. First, this includes the devicein the standard version, secondly the device with a membrane keyboard and thirdly the device with an MMI operating unit.The illustrated "frequency converter in standard version" is fully usable and contains a built-in potentiometer,but needs to control a corresponding control panel.For this purpose, one of the following options must be ordered: - External HMI device (MMI with cable and plug)- Interface cable for PC programming- Bluetooth adapter The variant "Frequency inverter with membrane keypad" offers the possibility to directly control the FI,such as Start-stop, left-right-run etc.For parameterization, one of the following options must also be ordered:: - External HMI device (MMI with cable and plug)- Interface cable for PC programming- Bluetooth adapter The variant "Frequency converter with MMI operating unit" does not require an optional operating unitIn addition, a display is included in the device cover. The mentioned options can be used if required.     Important notesThis drive is a custom-made product. A withdrawal or cancellation of the purchase is excluded!All product photos are non-binding examples!

Worm Gear Motor, Power= 1,1 KW, Speed= 2 to 16 rpm, Degree of protection= IP55, Insulation class= F (155°C), Operating mode= S1, Type of duty= S1- 100%,Hollow shaft= 42mm, Mounting position= M1-M6. Engine Speed= 4 pole, Ratio (i)= 100, Torque= 473 Nm,Service factor (f.s.)= 1 . Terminal box= top (rotatable), Weight= 52 kg , Paint= RAL 5010 (gentian blue),Temperature sensor= 3 x PTC-thermistors, Housing= Aluminum or cast iron, Ball bearings= SKF, C & U or equivalent, When ordering, please select the desired mounting position and design! Frequency InverterPower= 1.1 KW, Size= A, Input Voltage= 3 x 400V + 10% (three-phase), Input frequency= 50/60 Hz,Output frequency= 0-400 Hz, EMC filter= C2, Degree of protection= IP65, Dimensions=  233mm x 153mm x 120mm,Mains current (input)= 2.6 A. Ideal control range= 5-60 Hz, below 30 Hz, a forced cooling fan is used for coolingneeded. Product Information The frequency converter optionally offers the possibility of becoming "bus-capable" with the aid of fieldbus modules. With CANopen, EtherCAT, Modbus (already included), Profibus, Profinet and Sercos the EASYdrive offers Compatibility with almost all common interfaces. The customer can choose the relevant bus system for him and integrate the EASYdrive ideally in the control environment of its application.The required optional control variant must be specified for orders.The EASYdrive lasts without external filter measures the EMC class C2 (for 3-phase mains supply), or C1 (for 1-phase mains supply).   ! Possible variant selection!               Product selection When selecting the frequency converter, make sure that there are 3 variants. First, this includes the devicein the standard version, secondly the device with a membrane keyboard and thirdly the device with an MMI operating unit.The illustrated "frequency converter in standard version" is fully usable and contains a built-in potentiometer,but needs to control a corresponding control panel.For this purpose, one of the following options must be ordered: - External HMI device (MMI with cable and plug)- Interface cable for PC programming- Bluetooth adapter The variant "Frequency inverter with membrane keypad" offers the possibility to directly control the FI,such as Start-stop, left-right-run etc.For parameterization, one of the following options must also be ordered:: - External HMI device (MMI with cable and plug)- Interface cable for PC programming- Bluetooth adapter The variant "Frequency converter with MMI operating unit" does not require an optional operating unitIn addition, a display is included in the device cover. The mentioned options can be used if required.     Important notesThis drive is a custom-made product. A withdrawal or cancellation of the purchase is excluded!All product photos are non-binding examples!

Worm Gear Motor, Power= 2,2 KW, Speed= 7 to 84 rpm, Degree of protection= IP55, Insulation class= F (155°C), Operating mode= S1, Type of duty= S1- 100%,Hollow shaft= 35mm, Engine Speed= 4 pole, Ratio (i)= 20, Torque= 252 Nm,Service factor (f.s.)= 1,4 . Terminal box= top (rotatable), Weight= 38 kg, Paint= RAL 5010 (gentian blue),Temperature sensor= 3 x PTC-thermistors, Housing= Aluminum or cast iron, Ball bearings= SKF, C & U or equivalent, Frequency InverterPower= 2.2 KW, Size= B, Input Voltage= 3 x 400V + 10% (three-phase), Input frequency= 50/60 Hz,Output frequency= 0-400 Hz, EMC filter= C2, Degree of protection= IP65, Dimensions= 270mm x 189mm x 140mm,Mains current (input)= 4.6 A. Ideal control range= 5-60 Hz, below 30 Hz, a forced cooling fan is used for coolingneeded. Product Information The frequency converter optionally offers the possibility of becoming "bus-capable" with the aid of fieldbus modules. With CANopen, EtherCAT, Modbus (already included), Profibus, Profinet and Sercos the EASYdrive offers Compatibility with almost all common interfaces. The customer can choose the relevant bus system for him and integrate the EASYdrive ideally in the control environment of its application.The required optional control variant must be specified for orders.The EASYdrive lasts without external filter measures the EMC class C2 (for 3-phase mains supply), or C1 (for 1-phase mains supply).   ! Possible variant selection!               Product selection When selecting the frequency converter, make sure that there are 3 variants. First, this includes the devicein the standard version, secondly the device with a membrane keyboard and thirdly the device with an MMI operating unit.The illustrated "frequency converter in standard version" is fully usable and contains a built-in potentiometer,but needs to control a corresponding control panel.For this purpose, one of the following options must be ordered: - External HMI device (MMI with cable and plug)- Interface cable for PC programming- Bluetooth adapter The variant "Frequency inverter with membrane keypad" offers the possibility to directly control the FI,such as Start-stop, left-right-run etc.For parameterization, one of the following options must also be ordered:: - External HMI device (MMI with cable and plug)- Interface cable for PC programming- Bluetooth adapter The variant "Frequency converter with MMI operating unit" does not require an optional operating unitIn addition, a display is included in the device cover. The mentioned options can be used if required.     Important notesThis drive is a custom-made product. A withdrawal or cancellation of the purchase is excluded!All product photos are non-binding examples!

Worm Gear Motor, Power= 2,2 KW, Speed= 9 to 110 rpm, Degree of protection= IP55, Insulation class= F (155°C), Operating mode= S1, Type of duty= S1- 100%,Hollow shaft= 35mm, Engine Speed= 4 pole, Ratio (i)= 15, Torque= 194 Nm,Service factor (f.s.)= 1,9 . Terminal box= top (rotatable), Weight= 38 kg, Paint= RAL 5010 (gentian blue),Temperature sensor= 3 x PTC-thermistors, Housing= Aluminum or cast iron, Ball bearings= SKF, C & U or equivalent, Frequency InverterPower= 2.2 KW, Size= B, Input Voltage= 3 x 400V + 10% (three-phase), Input frequency= 50/60 Hz,Output frequency= 0-400 Hz, EMC filter= C2, Degree of protection= IP65, Dimensions= 270mm x 189mm x 140mm,Mains current (input)= 4.6 A. Ideal control range= 5-60 Hz, below 30 Hz, a forced cooling fan is used for coolingneeded. Product Information The frequency converter optionally offers the possibility of becoming "bus-capable" with the aid of fieldbus modules. With CANopen, EtherCAT, Modbus (already included), Profibus, Profinet and Sercos the EASYdrive offers Compatibility with almost all common interfaces. The customer can choose the relevant bus system for him and integrate the EASYdrive ideally in the control environment of its application.The required optional control variant must be specified for orders.The EASYdrive lasts without external filter measures the EMC class C2 (for 3-phase mains supply), or C1 (for 1-phase mains supply).   ! Possible variant selection!               Product selection When selecting the frequency converter, make sure that there are 3 variants. First, this includes the devicein the standard version, secondly the device with a membrane keyboard and thirdly the device with an MMI operating unit.The illustrated "frequency converter in standard version" is fully usable and contains a built-in potentiometer,but needs to control a corresponding control panel.For this purpose, one of the following options must be ordered: - External HMI device (MMI with cable and plug)- Interface cable for PC programming- Bluetooth adapter The variant "Frequency inverter with membrane keypad" offers the possibility to directly control the FI,such as Start-stop, left-right-run etc.For parameterization, one of the following options must also be ordered:: - External HMI device (MMI with cable and plug)- Interface cable for PC programming- Bluetooth adapter The variant "Frequency converter with MMI operating unit" does not require an optional operating unitIn addition, a display is included in the device cover. The mentioned options can be used if required.     Important notesThis drive is a custom-made product. A withdrawal or cancellation of the purchase is excluded!All product photos are non-binding examples!

Worm Gear Motor, Power= 2,2 KW, Speed= 14 to 168 rpm, Degree of protection= IP55, Insulation class= F (155°C), Operating mode= S1, Type of duty= S1- 100%,Hollow shaft= 35mm, Engine Speed= 4 pole, Ratio (i)= 10, Torque= 134 Nm,Service factor (f.s.)= 2,3 . Terminal box= top (rotatable), Weight= 38 kg, Paint= RAL 5010 (gentian blue),Temperature sensor= 3 x PTC-thermistors, Housing= Aluminum or cast iron, Ball bearings= SKF, C & U or equivalent, Frequency InverterPower= 2.2 KW, Size= B, Input Voltage= 3 x 400V + 10% (three-phase), Input frequency= 50/60 Hz,Output frequency= 0-400 Hz, EMC filter= C2, Degree of protection= IP65, Dimensions= 270mm x 189mm x 140mm,Mains current (input)= 4.6 A. Ideal control range= 5-60 Hz, below 30 Hz, a forced cooling fan is used for coolingneeded. Product Information The frequency converter optionally offers the possibility of becoming "bus-capable" with the aid of fieldbus modules. With CANopen, EtherCAT, Modbus (already included), Profibus, Profinet and Sercos the EASYdrive offers Compatibility with almost all common interfaces. The customer can choose the relevant bus system for him and integrate the EASYdrive ideally in the control environment of its application.The required optional control variant must be specified for orders.The EASYdrive lasts without external filter measures the EMC class C2 (for 3-phase mains supply), or C1 (for 1-phase mains supply).   ! Possible variant selection!               Product selection When selecting the frequency converter, make sure that there are 3 variants. First, this includes the devicein the standard version, secondly the device with a membrane keyboard and thirdly the device with an MMI operating unit.The illustrated "frequency converter in standard version" is fully usable and contains a built-in potentiometer,but needs to control a corresponding control panel.For this purpose, one of the following options must be ordered: - External HMI device (MMI with cable and plug)- Interface cable for PC programming- Bluetooth adapter The variant "Frequency inverter with membrane keypad" offers the possibility to directly control the FI,such as Start-stop, left-right-run etc.For parameterization, one of the following options must also be ordered:: - External HMI device (MMI with cable and plug)- Interface cable for PC programming- Bluetooth adapter The variant "Frequency converter with MMI operating unit" does not require an optional operating unitIn addition, a display is included in the device cover. The mentioned options can be used if required.     Important notesThis drive is a custom-made product. A withdrawal or cancellation of the purchase is excluded!All product photos are non-binding examples!

Worm Gear Motor, Power= 2,2 KW, Speed= 6 to 67 rpm, Degree of protection= IP55, Insulation class= F (155°C), Operating mode= S1, Type of duty= S1- 100%,Hollow shaft= 35mm, Engine Speed= 4 pole, Ratio (i)= 25, Torque= 308 Nm,Service factor (f.s.)= 1,1 . Terminal box= top (rotatable), Weight= 38 kg, Paint= RAL 5010 (gentian blue),Temperature sensor= 3 x PTC-thermistors, Housing= Aluminum or cast iron, Ball bearings= SKF, C & U or equivalent, Frequency InverterPower= 2.2 KW, Size= B, Input Voltage= 3 x 400V + 10% (three-phase), Input frequency= 50/60 Hz,Output frequency= 0-400 Hz, EMC filter= C2, Degree of protection= IP65, Dimensions= 270mm x 189mm x 140mm,Mains current (input)= 4.6 A. Ideal control range= 5-60 Hz, below 30 Hz, a forced cooling fan is used for coolingneeded. Product Information The frequency converter optionally offers the possibility of becoming "bus-capable" with the aid of fieldbus modules. With CANopen, EtherCAT, Modbus (already included), Profibus, Profinet and Sercos the EASYdrive offers Compatibility with almost all common interfaces. The customer can choose the relevant bus system for him and integrate the EASYdrive ideally in the control environment of its application.The required optional control variant must be specified for orders.The EASYdrive lasts without external filter measures the EMC class C2 (for 3-phase mains supply), or C1 (for 1-phase mains supply).   ! Possible variant selection!               Product selection When selecting the frequency converter, make sure that there are 3 variants. First, this includes the devicein the standard version, secondly the device with a membrane keyboard and thirdly the device with an MMI operating unit.The illustrated "frequency converter in standard version" is fully usable and contains a built-in potentiometer,but needs to control a corresponding control panel.For this purpose, one of the following options must be ordered: - External HMI device (MMI with cable and plug)- Interface cable for PC programming- Bluetooth adapter The variant "Frequency inverter with membrane keypad" offers the possibility to directly control the FI,such as Start-stop, left-right-run etc.For parameterization, one of the following options must also be ordered:: - External HMI device (MMI with cable and plug)- Interface cable for PC programming- Bluetooth adapter The variant "Frequency converter with MMI operating unit" does not require an optional operating unitIn addition, a display is included in the device cover. The mentioned options can be used if required.     Important notesThis drive is a custom-made product. A withdrawal or cancellation of the purchase is excluded!All product photos are non-binding examples!

Worm Gear Motor, Power= 3 KW, Speed= 14 to 168 rpm, Degree of protection= IP55, Insulation class= F (155°C), Operating mode= S1, Type of duty= S1- 100%,Hollow shaft= 28mm, Engine Speed= 4 pole, Ratio (i)= 10, Torque= 180 Nm,Service factor (f.s.)= 1,1 . Terminal box= top (rotatable), Weight= 38 kg, Paint= RAL 5010 (gentian blue),Temperature sensor= 3 x PTC-thermistors, Housing= Aluminum or cast iron, Ball bearings= SKF, C & U or equivalent, Frequency Inverter Power= 3.0 KW, Size= B, Input Voltage= 3 x 400V + 10% (three-phase), Input frequency= 50/60 Hz, Output frequency= 0-400 Hz, EMC filter= C2, Degree of protection= IP65, Dimensions= 270mm x 189mm x 140mm, Mains current (input)= 6.2 A. Ideal control range= 5-60 Hz, below 30 Hz, a forced cooling fan is used for cooling needed. Product Information The frequency converter optionally offers the possibility of becoming "bus-capable" with the aid of fieldbus modules. With CANopen, EtherCAT, Modbus (already included), Profibus, Profinet and Sercos the EASYdrive offers Compatibility with almost all common interfaces. The customer can choose the relevant bus system for him and integrate the EASYdrive ideally in the control environment of its application.The required optional control variant must be specified for orders.The EASYdrive lasts without external filter measures the EMC class C2 (for 3-phase mains supply), or C1 (for 1-phase mains supply).   ! Possible variant selection!               Product selection When selecting the frequency converter, make sure that there are 3 variants. First, this includes the devicein the standard version, secondly the device with a membrane keyboard and thirdly the device with an MMI operating unit.The illustrated "frequency converter in standard version" is fully usable and contains a built-in potentiometer,but needs to control a corresponding control panel.For this purpose, one of the following options must be ordered: - External HMI device (MMI with cable and plug)- Interface cable for PC programming- Bluetooth adapter The variant "Frequency inverter with membrane keypad" offers the possibility to directly control the FI,such as Start-stop, left-right-run etc.For parameterization, one of the following options must also be ordered:: - External HMI device (MMI with cable and plug)- Interface cable for PC programming- Bluetooth adapter The variant "Frequency converter with MMI operating unit" does not require an optional operating unitIn addition, a display is included in the device cover. The mentioned options can be used if required.     Important notesThis drive is a custom-made product. A withdrawal or cancellation of the purchase is excluded!All product photos are non-binding examples!

Worm Gear Motor, Power= 1,5 KW, Speed= 4 to 42 rpm, Degree of protection= IP55, Insulation class= F (155°C), Operating mode= S1, Type of duty= S1- 100%,Hollow shaft= 42mm, Mounting position= M1-M6. Engine Speed= 4 pole, Ratio (i)= 40, Torque= 319 Nm,Service factor (f.s.)= 2,2 . Terminal box= top (rotatable), Weight= 56 kg , Paint= RAL 5010 (gentian blue),Temperature sensor= 3 x PTC-thermistors, Housing= Aluminum or cast iron, Ball bearings= SKF, C & U or equivalent, When ordering, please select the desired mounting position and design! Frequency InverterPower= 1.5 KW, Size= A, Input Voltage= 3 x 400V + 10% (three-phase), Input frequency= 50/60 Hz,Output frequency= 0-400 Hz, EMC filter= C2, Degree of protection= IP65, Dimensions= 233mm x 153mm x 120mm,Mains current (input)= 3.3 A. Ideal control range= 5-60 Hz, below 30 Hz, a forced cooling fan is used for coolingneeded. Product Information The frequency converter optionally offers the possibility of becoming "bus-capable" with the aid of fieldbus modules. With CANopen, EtherCAT, Modbus (already included), Profibus, Profinet and Sercos the EASYdrive offers Compatibility with almost all common interfaces. The customer can choose the relevant bus system for him and integrate the EASYdrive ideally in the control environment of its application.The required optional control variant must be specified for orders.The EASYdrive lasts without external filter measures the EMC class C2 (for 3-phase mains supply), or C1 (for 1-phase mains supply).   ! Possible variant selection!               Product selection When selecting the frequency converter, make sure that there are 3 variants. First, this includes the devicein the standard version, secondly the device with a membrane keyboard and thirdly the device with an MMI operating unit.The illustrated "frequency converter in standard version" is fully usable and contains a built-in potentiometer,but needs to control a corresponding control panel.For this purpose, one of the following options must be ordered: - External HMI device (MMI with cable and plug)- Interface cable for PC programming- Bluetooth adapter The variant "Frequency inverter with membrane keypad" offers the possibility to directly control the FI,such as Start-stop, left-right-run etc.For parameterization, one of the following options must also be ordered:: - External HMI device (MMI with cable and plug)- Interface cable for PC programming- Bluetooth adapter The variant "Frequency converter with MMI operating unit" does not require an optional operating unitIn addition, a display is included in the device cover. The mentioned options can be used if required.     Important notesThis drive is a custom-made product. A withdrawal or cancellation of the purchase is excluded!All product photos are non-binding examples!

Worm Gear Motor, Power= 1,5 KW, Speed= 4 to 42 rpm, Degree of protection= IP55, Insulation class= F (155°C), Operating mode= S1, Type of duty= S1- 100%,Hollow shaft= 42mm, Mounting position= M1-M6. Engine Speed= 4 pole, Ratio (i)= 40, Torque= 319 Nm,Service factor (f.s.)= 2,2 . Terminal box= top (rotatable), Weight= 56 kg , Paint= RAL 5010 (gentian blue),Temperature sensor= 3 x PTC-thermistors, Housing= Aluminum or cast iron, Ball bearings= SKF, C & U or equivalent, When ordering, please select the desired mounting position and design! Frequency InverterPower= 1.1 KW, Size= A, Input Voltage= 1 x 230V +10% (single phase), Input frequency= 50/60 Hz,Output frequency= 0-400 Hz, EMC filter= C1, Degree of protection= IP65, Dimensions= 233mm x 153mm x 120mm,Mains current (input)= 9.2 A. Ideal control range= 5-60 Hz, below 30 Hz, a forced cooling fan is used for coolingneeded. Product Information The frequency converter optionally offers the possibility of becoming "bus-capable" with the aid of fieldbus modules. With CANopen, EtherCAT, Modbus (already included), Profibus, Profinet and Sercos the EASYdrive offers Compatibility with almost all common interfaces. The customer can choose the relevant bus system for him and integrate the EASYdrive ideally in the control environment of its application.The required optional control variant must be specified for orders.The EASYdrive lasts without external filter measures the EMC class C2 (for 3-phase mains supply), or C1 (for 1-phase mains supply).   ! Possible variant selection!               Product selection When selecting the frequency converter, make sure that there are 3 variants. First, this includes the devicein the standard version, secondly the device with a membrane keyboard and thirdly the device with an MMI operating unit.The illustrated "frequency converter in standard version" is fully usable and contains a built-in potentiometer,but needs to control a corresponding control panel.For this purpose, one of the following options must be ordered: - External HMI device (MMI with cable and plug)- Interface cable for PC programming- Bluetooth adapter The variant "Frequency inverter with membrane keypad" offers the possibility to directly control the FI,such as Start-stop, left-right-run etc.For parameterization, one of the following options must also be ordered:: - External HMI device (MMI with cable and plug)- Interface cable for PC programming- Bluetooth adapter The variant "Frequency converter with MMI operating unit" does not require an optional operating unitIn addition, a display is included in the device cover. The mentioned options can be used if required.     Important notesThis drive is a custom-made product. A withdrawal or cancellation of the purchase is excluded!All product photos are non-binding examples!

Worm Gear Motor, Power= 3 KW, Speed= 14 to 168 rpm, Degree of protection= IP55, Insulation class= F (155°C), Operating mode= S1, Type of duty= S1- 100%,Hollow shaft= 35mm, Engine Speed= 4 pole, Ratio (i)= 10, Torque= 182 Nm,Service factor (f.s.)= 1,7 . Terminal box= top (rotatable), Weight= 42 kg, Paint= RAL 5010 (gentian blue),Temperature sensor= 3 x PTC-thermistors, Housing= Aluminum or cast iron, Ball bearings= SKF, C & U or equivalent, Frequency inverter Power= 3.0 KW, Size= B, Input Voltage= 3 x 400V + 10% (three-phase), Input frequency= 50/60 Hz, Output frequency= 0-400 Hz, EMC filter= C2, Degree of protection= IP65, Dimensions= 270mm x 189mm x 140mm, Mains current (input)= 6.2 A. Ideal control range= 5-60 Hz, below 30 Hz, a forced cooling fan is used for cooling needed.  Product Information The frequency converter optionally offers the possibility of becoming "bus-capable" with the aid of fieldbus modules. With CANopen, EtherCAT, Modbus (already included), Profibus, Profinet and Sercos the EASYdrive offers Compatibility with almost all common interfaces. The customer can choose the relevant bus system for him and integrate the EASYdrive ideally in the control environment of its application.The required optional control variant must be specified for orders.The EASYdrive lasts without external filter measures the EMC class C2 (for 3-phase mains supply), or C1 (for 1-phase mains supply).                           ! Possible variant selection!               Product selection When selecting the frequency converter, make sure that there are 3 variants. First, this includes the devicein the standard version, secondly the device with a membrane keyboard and thirdly the device with an MMI operating unit.The illustrated "frequency converter in standard version" is fully usable and contains a built-in potentiometer,but needs to control a corresponding control panel.For this purpose, one of the following options must be ordered: - External HMI device (MMI with cable and plug)- Interface cable for PC programming- Bluetooth adapter The variant "Frequency inverter with membrane keypad" offers the possibility to directly control the FI,such as Start-stop, left-right-run etc.For parameterization, one of the following options must also be ordered: - External HMI device (MMI with cable and plug)- Interface cable for PC programming- Bluetooth adapter The variant "Frequency inverter with membrane keypad" offers the possibility to directly control the FI,such as Start-stop, left-right-run etc.For parameterization, one of the following options must also be ordered: - External HMI device (MMI with cable and plug)- Interface cable for PC programming- Bluetooth adapter  The variant "Frequency inverter with MMI operating unit" does not require an optional operating unit,in addition, a display is included in the device cover. The mentioned options can be used if required.     Important notesThis drive is a custom-made product. A withdrawal or cancellation of the purchase is excluded!All product photos are non-binding examples!

Worm Gear Motor, Power= 3 KW, Speed= 9 to 110 rpm, Degree of protection= IP55, Insulation class= F (155°C), Operating mode= S1, Type of duty= S1- 100%,Hollow shaft= 35mm, Engine Speed= 4 pole, Ratio (i)= 15, Torque= 264 Nm,Service factor (f.s.)= 1,4 . Terminal box= top (rotatable), Weight= 42 kg, Paint= RAL 5010 (gentian blue),Temperature sensor= 3 x PTC-thermistors, Housing= Aluminum or cast iron, Ball bearings= SKF, C & U or equivalent, Frequency Inverter Power= 3.0 KW, Size= B, Input Voltage= 3 x 400V + 10% (three-phase), Input frequency= 50/60 Hz, Output frequency= 0-400 Hz, EMC filter= C2, Degree of protection= IP65, Dimensions= 270mm x 189mm x 140mm, Mains current (input)= 6.2 A. Ideal control range= 5-60 Hz, below 30 Hz, a forced cooling fan is used for cooling needed. Product Information The frequency converter optionally offers the possibility of becoming "bus-capable" with the aid of fieldbus modules. With CANopen, EtherCAT, Modbus (already included), Profibus, Profinet and Sercos the EASYdrive offers Compatibility with almost all common interfaces. The customer can choose the relevant bus system for him and integrate the EASYdrive ideally in the control environment of its application.The required optional control variant must be specified for orders.The EASYdrive lasts without external filter measures the EMC class C2 (for 3-phase mains supply), or C1 (for 1-phase mains supply).   ! Possible variant selection!               Product selection When selecting the frequency converter, make sure that there are 3 variants. First, this includes the devicein the standard version, secondly the device with a membrane keyboard and thirdly the device with an MMI operating unit.The illustrated "frequency converter in standard version" is fully usable and contains a built-in potentiometer,but needs to control a corresponding control panel.For this purpose, one of the following options must be ordered: - External HMI device (MMI with cable and plug)- Interface cable for PC programming- Bluetooth adapter The variant "Frequency inverter with membrane keypad" offers the possibility to directly control the FI,such as Start-stop, left-right-run etc.For parameterization, one of the following options must also be ordered:: - External HMI device (MMI with cable and plug)- Interface cable for PC programming- Bluetooth adapter The variant "Frequency converter with MMI operating unit" does not require an optional operating unitIn addition, a display is included in the device cover. The mentioned options can be used if required.     Important notesThis drive is a custom-made product. A withdrawal or cancellation of the purchase is excluded!All product photos are non-binding examples!

Worm Gear Motor, Power= 3 KW, Speed= 7 to 84 rpm, Degree of protection= IP55, Insulation class= F (155°C), Operating mode= S1, Type of duty= S1- 100%,Hollow shaft= 35mm, Engine Speed= 4 pole, Ratio (i)= 20, Torque= 344 Nm,Service factor (f.s.)= 1 . Terminal box= top (rotatable), Weight= 42 kg, Paint= RAL 5010 (gentian blue),Temperature sensor= 3 x PTC-thermistors, Housing= Aluminum or cast iron, Ball bearings= SKF, C & U or equivalent, Frequency Inverter Power= 3.0 KW, Size= B, Input Voltage= 3 x 400V + 10% (three-phase), Input frequency= 50/60 Hz, Output frequency= 0-400 Hz, EMC filter= C2, Degree of protection= IP65, Dimensions= 270mm x 189mm x 140mm, Mains current (input)= 6.2 A. Ideal control range= 5-60 Hz, below 30 Hz, a forced cooling fan is used for cooling needed. Product Information The frequency converter optionally offers the possibility of becoming "bus-capable" with the aid of fieldbus modules. With CANopen, EtherCAT, Modbus (already included), Profibus, Profinet and Sercos the EASYdrive offers Compatibility with almost all common interfaces. The customer can choose the relevant bus system for him and integrate the EASYdrive ideally in the control environment of its application.The required optional control variant must be specified for orders.The EASYdrive lasts without external filter measures the EMC class C2 (for 3-phase mains supply), or C1 (for 1-phase mains supply).   ! Possible variant selection!               Product selection When selecting the frequency converter, make sure that there are 3 variants. First, this includes the devicein the standard version, secondly the device with a membrane keyboard and thirdly the device with an MMI operating unit.The illustrated "frequency converter in standard version" is fully usable and contains a built-in potentiometer,but needs to control a corresponding control panel.For this purpose, one of the following options must be ordered: - External HMI device (MMI with cable and plug)- Interface cable for PC programming- Bluetooth adapter The variant "Frequency inverter with membrane keypad" offers the possibility to directly control the FI,such as Start-stop, left-right-run etc.For parameterization, one of the following options must also be ordered:: - External HMI device (MMI with cable and plug)- Interface cable for PC programming- Bluetooth adapter The variant "Frequency converter with MMI operating unit" does not require an optional operating unitIn addition, a display is included in the device cover. The mentioned options can be used if required.     Important notesThis drive is a custom-made product. A withdrawal or cancellation of the purchase is excluded!All product photos are non-binding examples!

Worm Gear Motor, Power= 1,1 KW, Speed= 2 to 16 rpm, Degree of protection= IP55, Insulation class= F (155°C), Operating mode= S1, Type of duty= S1- 100%,Hollow shaft= 45mm, Mounting position= M1-M6. Engine Speed= 4 pole, Ratio (i)= 100, Torque= 480 Nm,Service factor (f.s.)= 1,5 . Terminal box= top (rotatable), Weight= 65 kg , Paint= RAL 5010 (gentian blue),Temperature sensor= 3 x PTC-thermistors, Housing= Aluminum or cast iron, Ball bearings= SKF, C & U or equivalent, When ordering, please select the desired mounting position and design! Frequency InverterPower= 1.1 KW, Size= A, Input Voltage= 3 x 400V + 10% (three-phase), Input frequency= 50/60 Hz,Output frequency= 0-400 Hz, EMC filter= C2, Degree of protection= IP65, Dimensions=  233mm x 153mm x 120mm,Mains current (input)= 2.6 A. Ideal control range= 5-60 Hz, below 30 Hz, a forced cooling fan is used for coolingneeded. Product Information The frequency converter optionally offers the possibility of becoming "bus-capable" with the aid of fieldbus modules. With CANopen, EtherCAT, Modbus (already included), Profibus, Profinet and Sercos the EASYdrive offers Compatibility with almost all common interfaces. The customer can choose the relevant bus system for him and integrate the EASYdrive ideally in the control environment of its application.The required optional control variant must be specified for orders.The EASYdrive lasts without external filter measures the EMC class C2 (for 3-phase mains supply), or C1 (for 1-phase mains supply).   ! Possible variant selection!               Product selection When selecting the frequency converter, make sure that there are 3 variants. First, this includes the devicein the standard version, secondly the device with a membrane keyboard and thirdly the device with an MMI operating unit.The illustrated "frequency converter in standard version" is fully usable and contains a built-in potentiometer,but needs to control a corresponding control panel.For this purpose, one of the following options must be ordered: - External HMI device (MMI with cable and plug)- Interface cable for PC programming- Bluetooth adapter The variant "Frequency inverter with membrane keypad" offers the possibility to directly control the FI,such as Start-stop, left-right-run etc.For parameterization, one of the following options must also be ordered:: - External HMI device (MMI with cable and plug)- Interface cable for PC programming- Bluetooth adapter The variant "Frequency converter with MMI operating unit" does not require an optional operating unitIn addition, a display is included in the device cover. The mentioned options can be used if required.     Important notesThis drive is a custom-made product. A withdrawal or cancellation of the purchase is excluded!All product photos are non-binding examples!

Worm Gear Motor, Power= 1,1 KW, Speed= 2 to 16 rpm, Degree of protection= IP55, Insulation class= F (155°C), Operating mode= S1, Type of duty= S1- 100%,Hollow shaft= 45mm, Mounting position= M1-M6. Engine Speed= 4 pole, Ratio (i)= 100, Torque= 480 Nm,Service factor (f.s.)= 1,5 . Terminal box= top (rotatable), Weight= 65 kg , Paint= RAL 5010 (gentian blue),Temperature sensor= 3 x PTC-thermistors, Housing= Aluminum or cast iron, Ball bearings= SKF, C & U or equivalent, When ordering, please select the desired mounting position and design! Frequency InverterPower= 1.1 KW, Size= A, Input Voltage= 1 x 230V +10% (single phase), Input frequency= 50/60 Hz,Output frequency= 0-400 Hz, EMC filter= C1, Degree of protection= IP65, Dimensions= 233mm x 153mm x 120mm,Mains current (input)= 9.2 A. Ideal control range= 5-60 Hz, below 30 Hz, a forced cooling fan is used for coolingneeded. Product Information The frequency converter optionally offers the possibility of becoming "bus-capable" with the aid of fieldbus modules. With CANopen, EtherCAT, Modbus (already included), Profibus, Profinet and Sercos the EASYdrive offers Compatibility with almost all common interfaces. The customer can choose the relevant bus system for him and integrate the EASYdrive ideally in the control environment of its application.The required optional control variant must be specified for orders.The EASYdrive lasts without external filter measures the EMC class C2 (for 3-phase mains supply), or C1 (for 1-phase mains supply).   ! Possible variant selection!               Product selection When selecting the frequency converter, make sure that there are 3 variants. First, this includes the devicein the standard version, secondly the device with a membrane keyboard and thirdly the device with an MMI operating unit.The illustrated "frequency converter in standard version" is fully usable and contains a built-in potentiometer,but needs to control a corresponding control panel.For this purpose, one of the following options must be ordered: - External HMI device (MMI with cable and plug)- Interface cable for PC programming- Bluetooth adapter The variant "Frequency inverter with membrane keypad" offers the possibility to directly control the FI,such as Start-stop, left-right-run etc.For parameterization, one of the following options must also be ordered:: - External HMI device (MMI with cable and plug)- Interface cable for PC programming- Bluetooth adapter The variant "Frequency converter with MMI operating unit" does not require an optional operating unitIn addition, a display is included in the device cover. The mentioned options can be used if required.     Important notesThis drive is a custom-made product. A withdrawal or cancellation of the purchase is excluded!All product photos are non-binding examples!

Worm Gear Motor, Power= 2,2 KW, Speed= 4 to 42 rpm, Degree of protection= IP55, Insulation class= F (155°C), Operating mode= S1, Type of duty= S1- 100%,Hollow shaft= 42mm, Mounting position= M1-M6. Engine Speed= 4 pole, Ratio (i)= 40, Torque= 468 Nm,Service factor (f.s.)= 1,5 . Terminal box= top (rotatable), Weight= 60 kg , Paint= RAL 5010 (gentian blue),Temperature sensor= 3 x PTC-thermistors, Housing= Aluminum or cast iron, Ball bearings= SKF, C & U or equivalent, When ordering, please select the desired mounting position and design! Frequency InverterPower= 2.2 KW, Size= B, Input Voltage= 3 x 400V + 10% (three-phase), Input frequency= 50/60 Hz,Output frequency= 0-400 Hz, EMC filter= C2, Degree of protection= IP65, Dimensions= 270mm x 189mm x 140mm,Mains current (input)= 4.6 A. Ideal control range= 5-60 Hz, below 30 Hz, a forced cooling fan is used for coolingneeded. Product Information The frequency converter optionally offers the possibility of becoming "bus-capable" with the aid of fieldbus modules. With CANopen, EtherCAT, Modbus (already included), Profibus, Profinet and Sercos the EASYdrive offers Compatibility with almost all common interfaces. The customer can choose the relevant bus system for him and integrate the EASYdrive ideally in the control environment of its application.The required optional control variant must be specified for orders.The EASYdrive lasts without external filter measures the EMC class C2 (for 3-phase mains supply), or C1 (for 1-phase mains supply).   ! Possible variant selection!               Product selection When selecting the frequency converter, make sure that there are 3 variants. First, this includes the devicein the standard version, secondly the device with a membrane keyboard and thirdly the device with an MMI operating unit.The illustrated "frequency converter in standard version" is fully usable and contains a built-in potentiometer,but needs to control a corresponding control panel.For this purpose, one of the following options must be ordered: - External HMI device (MMI with cable and plug)- Interface cable for PC programming- Bluetooth adapter The variant "Frequency inverter with membrane keypad" offers the possibility to directly control the FI,such as Start-stop, left-right-run etc.For parameterization, one of the following options must also be ordered:: - External HMI device (MMI with cable and plug)- Interface cable for PC programming- Bluetooth adapter The variant "Frequency converter with MMI operating unit" does not require an optional operating unitIn addition, a display is included in the device cover. The mentioned options can be used if required.     Important notesThis drive is a custom-made product. A withdrawal or cancellation of the purchase is excluded!All product photos are non-binding examples!

Worm Gear Motor, Power= 2,2 KW, Speed= 6 to 67 rpm, Degree of protection= IP55, Insulation class= F (155°C), Operating mode= S1, Type of duty= S1- 100%,Hollow shaft= 42mm, Mounting position= M1-M6. Engine Speed= 4 pole, Ratio (i)= 25, Torque= 315 Nm,Service factor (f.s.)= 2,2 . Terminal box= top (rotatable), Weight= 60 kg , Paint= RAL 5010 (gentian blue),Temperature sensor= 3 x PTC-thermistors, Housing= Aluminum or cast iron, Ball bearings= SKF, C & U or equivalent, When ordering, please select the desired mounting position and design! Frequency InverterPower= 2.2 KW, Size= B, Input Voltage= 3 x 400V + 10% (three-phase), Input frequency= 50/60 Hz,Output frequency= 0-400 Hz, EMC filter= C2, Degree of protection= IP65, Dimensions= 270mm x 189mm x 140mm,Mains current (input)= 4.6 A. Ideal control range= 5-60 Hz, below 30 Hz, a forced cooling fan is used for coolingneeded. Product Information The frequency converter optionally offers the possibility of becoming "bus-capable" with the aid of fieldbus modules. With CANopen, EtherCAT, Modbus (already included), Profibus, Profinet and Sercos the EASYdrive offers Compatibility with almost all common interfaces. The customer can choose the relevant bus system for him and integrate the EASYdrive ideally in the control environment of its application.The required optional control variant must be specified for orders.The EASYdrive lasts without external filter measures the EMC class C2 (for 3-phase mains supply), or C1 (for 1-phase mains supply).   ! Possible variant selection!               Product selection When selecting the frequency converter, make sure that there are 3 variants. First, this includes the devicein the standard version, secondly the device with a membrane keyboard and thirdly the device with an MMI operating unit.The illustrated "frequency converter in standard version" is fully usable and contains a built-in potentiometer,but needs to control a corresponding control panel.For this purpose, one of the following options must be ordered: - External HMI device (MMI with cable and plug)- Interface cable for PC programming- Bluetooth adapter The variant "Frequency inverter with membrane keypad" offers the possibility to directly control the FI,such as Start-stop, left-right-run etc.For parameterization, one of the following options must also be ordered:: - External HMI device (MMI with cable and plug)- Interface cable for PC programming- Bluetooth adapter The variant "Frequency converter with MMI operating unit" does not require an optional operating unitIn addition, a display is included in the device cover. The mentioned options can be used if required.     Important notesThis drive is a custom-made product. A withdrawal or cancellation of the purchase is excluded!All product photos are non-binding examples!

Worm Gear Motor, Power= 2,2 KW, Speed= 7 to 84 rpm, Degree of protection= IP55, Insulation class= F (155°C), Operating mode= S1, Type of duty= S1- 100%,Hollow shaft= 42mm, Mounting position= M1-M6. Engine Speed= 4 pole, Ratio (i)= 20, Torque= 255 Nm,Service factor (f.s.)= 2,5 . Terminal box= top (rotatable), Weight= 60 kg , Paint= RAL 5010 (gentian blue),Temperature sensor= 3 x PTC-thermistors, Housing= Aluminum or cast iron, Ball bearings= SKF, C & U or equivalent, When ordering, please select the desired mounting position and design! Frequency InverterPower= 2.2 KW, Size= B, Input Voltage= 3 x 400V + 10% (three-phase), Input frequency= 50/60 Hz,Output frequency= 0-400 Hz, EMC filter= C2, Degree of protection= IP65, Dimensions= 270mm x 189mm x 140mm,Mains current (input)= 4.6 A. Ideal control range= 5-60 Hz, below 30 Hz, a forced cooling fan is used for coolingneeded. Product Information The frequency converter optionally offers the possibility of becoming "bus-capable" with the aid of fieldbus modules. With CANopen, EtherCAT, Modbus (already included), Profibus, Profinet and Sercos the EASYdrive offers Compatibility with almost all common interfaces. The customer can choose the relevant bus system for him and integrate the EASYdrive ideally in the control environment of its application.The required optional control variant must be specified for orders.The EASYdrive lasts without external filter measures the EMC class C2 (for 3-phase mains supply), or C1 (for 1-phase mains supply).   ! Possible variant selection!               Product selection When selecting the frequency converter, make sure that there are 3 variants. First, this includes the devicein the standard version, secondly the device with a membrane keyboard and thirdly the device with an MMI operating unit.The illustrated "frequency converter in standard version" is fully usable and contains a built-in potentiometer,but needs to control a corresponding control panel.For this purpose, one of the following options must be ordered: - External HMI device (MMI with cable and plug)- Interface cable for PC programming- Bluetooth adapter The variant "Frequency inverter with membrane keypad" offers the possibility to directly control the FI,such as Start-stop, left-right-run etc.For parameterization, one of the following options must also be ordered:: - External HMI device (MMI with cable and plug)- Interface cable for PC programming- Bluetooth adapter The variant "Frequency converter with MMI operating unit" does not require an optional operating unitIn addition, a display is included in the device cover. The mentioned options can be used if required.     Important notesThis drive is a custom-made product. A withdrawal or cancellation of the purchase is excluded!All product photos are non-binding examples!

Worm Gear Motor, Power= 1,5 KW, Speed= 2 to 16 rpm, Degree of protection= IP55, Insulation class= F (155°C), Operating mode= S1, Type of duty= S1- 100%,Hollow shaft= 45mm, Mounting position= M1-M6. Engine Speed= 4 pole, Ratio (i)= 100, Torque= 655 Nm,Service factor (f.s.)= 1,1 . Terminal box= top (rotatable), Weight= 69 kg , Paint= RAL 5010 (gentian blue),Temperature sensor= 3 x PTC-thermistors, Housing= Aluminum or cast iron, Ball bearings= SKF, C & U or equivalent, When ordering, please select the desired mounting position and design! Frequency InverterPower= 1.5 KW, Size= A, Input Voltage= 3 x 400V + 10% (three-phase), Input frequency= 50/60 Hz,Output frequency= 0-400 Hz, EMC filter= C2, Degree of protection= IP65, Dimensions= 233mm x 153mm x 120mm,Mains current (input)= 3.3 A. Ideal control range= 5-60 Hz, below 30 Hz, a forced cooling fan is used for coolingneeded. Product Information The frequency converter optionally offers the possibility of becoming "bus-capable" with the aid of fieldbus modules. With CANopen, EtherCAT, Modbus (already included), Profibus, Profinet and Sercos the EASYdrive offers Compatibility with almost all common interfaces. The customer can choose the relevant bus system for him and integrate the EASYdrive ideally in the control environment of its application.The required optional control variant must be specified for orders.The EASYdrive lasts without external filter measures the EMC class C2 (for 3-phase mains supply), or C1 (for 1-phase mains supply).   ! Possible variant selection!               Product selection When selecting the frequency converter, make sure that there are 3 variants. First, this includes the devicein the standard version, secondly the device with a membrane keyboard and thirdly the device with an MMI operating unit.The illustrated "frequency converter in standard version" is fully usable and contains a built-in potentiometer,but needs to control a corresponding control panel.For this purpose, one of the following options must be ordered: - External HMI device (MMI with cable and plug)- Interface cable for PC programming- Bluetooth adapter The variant "Frequency inverter with membrane keypad" offers the possibility to directly control the FI,such as Start-stop, left-right-run etc.For parameterization, one of the following options must also be ordered:: - External HMI device (MMI with cable and plug)- Interface cable for PC programming- Bluetooth adapter The variant "Frequency converter with MMI operating unit" does not require an optional operating unitIn addition, a display is included in the device cover. The mentioned options can be used if required.     Important notesThis drive is a custom-made product. A withdrawal or cancellation of the purchase is excluded!All product photos are non-binding examples!

Worm Gear Motor, Power= 1,5 KW, Speed= 2 to 16 rpm, Degree of protection= IP55, Insulation class= F (155°C), Operating mode= S1, Type of duty= S1- 100%,Hollow shaft= 45mm, Mounting position= M1-M6. Engine Speed= 4 pole, Ratio (i)= 100, Torque= 655 Nm,Service factor (f.s.)= 1,1 . Terminal box= top (rotatable), Weight= 69 kg , Paint= RAL 5010 (gentian blue),Temperature sensor= 3 x PTC-thermistors, Housing= Aluminum or cast iron, Ball bearings= SKF, C & U or equivalent, When ordering, please select the desired mounting position and design! Frequency InverterPower= 1.1 KW, Size= A, Input Voltage= 1 x 230V +10% (single phase), Input frequency= 50/60 Hz,Output frequency= 0-400 Hz, EMC filter= C1, Degree of protection= IP65, Dimensions= 233mm x 153mm x 120mm,Mains current (input)= 9.2 A. Ideal control range= 5-60 Hz, below 30 Hz, a forced cooling fan is used for coolingneeded. Product Information The frequency converter optionally offers the possibility of becoming "bus-capable" with the aid of fieldbus modules. With CANopen, EtherCAT, Modbus (already included), Profibus, Profinet and Sercos the EASYdrive offers Compatibility with almost all common interfaces. The customer can choose the relevant bus system for him and integrate the EASYdrive ideally in the control environment of its application.The required optional control variant must be specified for orders.The EASYdrive lasts without external filter measures the EMC class C2 (for 3-phase mains supply), or C1 (for 1-phase mains supply).   ! Possible variant selection!               Product selection When selecting the frequency converter, make sure that there are 3 variants. First, this includes the devicein the standard version, secondly the device with a membrane keyboard and thirdly the device with an MMI operating unit.The illustrated "frequency converter in standard version" is fully usable and contains a built-in potentiometer,but needs to control a corresponding control panel.For this purpose, one of the following options must be ordered: - External HMI device (MMI with cable and plug)- Interface cable for PC programming- Bluetooth adapter The variant "Frequency inverter with membrane keypad" offers the possibility to directly control the FI,such as Start-stop, left-right-run etc.For parameterization, one of the following options must also be ordered:: - External HMI device (MMI with cable and plug)- Interface cable for PC programming- Bluetooth adapter The variant "Frequency converter with MMI operating unit" does not require an optional operating unitIn addition, a display is included in the device cover. The mentioned options can be used if required.     Important notesThis drive is a custom-made product. A withdrawal or cancellation of the purchase is excluded!All product photos are non-binding examples!

Worm Gear Motor, Power= 4 KW, Speed= 9 to 110 rpm, Voltage= 3 x 400/690 V-50 Hz, 3 x 460/795 V-60 Hz (± 5% In according to the VDE 0530),Degree of protection= IP55, Insulation class= F (155°C), Operating mode= S1, Type of duty= S1- 100%,Hollow shaft= 35mm, Engine Speed= 4 pole, Ratio (i)= 15, Torque= 352 Nm,Service factor (f.s.)= 1 . Terminal box= top (rotatable), Weight= 55 kg, Paint= RAL 5010 (gentian blue),Temperature sensor= 3 x PTC-thermistors, Housing= Aluminum or cast iron, Ball bearings= SKF, C & U or equivalent, Frequency InverterPower= 4.0 KW, Size= B, Input Voltage= 3 x 400V + 10% (three-phase), Input frequency= 50/60 Hz,Output frequency= 0-400 Hz, EMC filter= C2, Degree of protection= IP65, Dimensions= 270mm x 189mm x 140mm,Mains current (input)= 7.9 A. Ideal control range= 5-60 Hz, below 30 Hz, a forced cooling fan is used for coolingneeded. Product Information The frequency converter optionally offers the possibility of becoming "bus-capable" with the aid of fieldbus modules. With CANopen, EtherCAT, Modbus (already included), Profibus, Profinet and Sercos the EASYdrive offers Compatibility with almost all common interfaces. The customer can choose the relevant bus system for him and integrate the EASYdrive ideally in the control environment of its application.The required optional control variant must be specified for orders.The EASYdrive lasts without external filter measures the EMC class C2 (for 3-phase mains supply), or C1 (for 1-phase mains supply).   ! Possible variant selection!               Product selection When selecting the frequency converter, make sure that there are 3 variants. First, this includes the devicein the standard version, secondly the device with a membrane keyboard and thirdly the device with an MMI operating unit.The illustrated "frequency converter in standard version" is fully usable and contains a built-in potentiometer,but needs to control a corresponding control panel.For this purpose, one of the following options must be ordered: - External HMI device (MMI with cable and plug)- Interface cable for PC programming- Bluetooth adapter The variant "Frequency inverter with membrane keypad" offers the possibility to directly control the FI,such as Start-stop, left-right-run etc.For parameterization, one of the following options must also be ordered:: - External HMI device (MMI with cable and plug)- Interface cable for PC programming- Bluetooth adapter The variant "Frequency converter with MMI operating unit" does not require an optional operating unitIn addition, a display is included in the device cover. The mentioned options can be used if required.     Important notesThis drive is a custom-made product. A withdrawal or cancellation of the purchase is excluded!All product photos are non-binding examples!

worm gear + FU motor ED400, Power= 4 KW, Speed= 7 to 84 rpm Voltage= 3 x 400/690 V-50 Hz, 3 x 460/795 V-60 Hz (± 5% according to VDE 0530),Protection class= IP55, iso class= F (155°C), Operating mode= S1, duty cycle= S1- 100%,hollow shaft= 35mm, motor Speed= 4 pole, translation (i)= 20, torque= 458 Nm,service factor (f.s.)= 0.8. Terminal box= on top (rotatable), weight= 55 kg, color= RAL 5010 (gentian blue),temperature sensor= 3 x PTC thermistor, housing= die-cast aluminum, ball bearing= SKF, C&U or equivalent, Frequency converterPower= 4 KW, Size= B, Input voltage= 3 x 400V +10% (three-phase), Input frequency= 50/60 Hz,Output frequency= 0 - 400 Hz, EMC filter= C2, degree of protection= IP65, dimensions= 270mm x 189mm x 140mm,Mains current (input) = 7.9 A. Ideal control range= 5- 60 Hz, with constant nominal torque, below 30 Hz, an external fan is required for cooling. Product informationThe frequency converter offers the option of becoming "bus-capable" with the help of fieldbus modules.With CANopen, EtherCAT, Modbus (already included), Profibus, Profinet and Sercos, the EASYdrive offers compatibility with almost all common control environments. The customer can select the bus system relevant to him and thus ideally integrate the EASYdrive into the control environment of his application. The required optional control variant must be specified when ordering. The EASYdrive drive controllers are CE, UL and CSA certified. Without external filter measures, the EASYdrive complieswith EMC class C2 (with 3-phase mains feed) or C1 (with 1-phase mains feed). Possible variant selection !               Product selectionWhen selecting the frequency converter, note that there are 3 variants. This includes the devicein the standard version, secondly the device with a membrane keyboard and thirdly the device with an MMI operating unit. The "standard frequency converter" shown is fully usable and contains a side-installed potentiometer, but requires a corresponding control panel for activation. One of the following options must also be ordered for this:- External operating/programming device (MMI with cable and plug)- Interface cable for PC programming    - Bluetooth adapter The variant "frequency converter with membrane keyboard" contains a built-in potentiometer and offers the possibility of controlling the FI directly, such as start-stop, left-right rotation, etc. For parameterization, you must also one of the following options can also be ordered:- External operating / programming device (MMI with cable and plug)- Interface cable for PC programming - Bluetooth adapter The "frequency converter with MMI control unit" variant does not require an optional control panel,there is also a display in the device cover. The options mentioned can be used if required.     Important informationThis drive is a custom-made product. A withdrawal or revocation of the purchase is excluded!All product photos are non-binding examples!

Worm Gear Motor, Power= 4 KW, Speed= 14 to 168 rpm, Voltage= 3 x 400/690 V-50 Hz, 3 x 460/795 V-60 Hz (± 5% In according to the VDE 0530),Degree of protection= IP55, Insulation class= F (155°C), Operating mode= S1, Type of duty= S1- 100%,Hollow shaft= 35mm, Engine Speed= 4 pole, Ratio (i)= 10, Torque= 243 Nm,Service factor (f.s.)= 1,3 . Terminal box= top (rotatable), Weight= 55 kg, Paint= RAL 5010 (gentian blue),Temperature sensor= 3 x PTC-thermistors, Housing= Aluminum or cast iron, Ball bearings= SKF, C & U or equivalent, Frequency InverterPower= 4.0 KW, Size= B, Input Voltage= 3 x 400V + 10% (three-phase), Input frequency= 50/60 Hz,Output frequency= 0-400 Hz, EMC filter= C2, Degree of protection= IP65, Dimensions= 270mm x 189mm x 140mm,Mains current (input)= 7.9 A. Ideal control range= 5-60 Hz, below 30 Hz, a forced cooling fan is used for coolingneeded. Product Information The frequency converter optionally offers the possibility of becoming "bus-capable" with the aid of fieldbus modules. With CANopen, EtherCAT, Modbus (already included), Profibus, Profinet and Sercos the EASYdrive offers Compatibility with almost all common interfaces. The customer can choose the relevant bus system for him and integrate the EASYdrive ideally in the control environment of its application.The required optional control variant must be specified for orders.The EASYdrive lasts without external filter measures the EMC class C2 (for 3-phase mains supply), or C1 (for 1-phase mains supply).   ! Possible variant selection!               Product selection When selecting the frequency converter, make sure that there are 3 variants. First, this includes the devicein the standard version, secondly the device with a membrane keyboard and thirdly the device with an MMI operating unit.The illustrated "frequency converter in standard version" is fully usable and contains a built-in potentiometer,but needs to control a corresponding control panel.For this purpose, one of the following options must be ordered: - External HMI device (MMI with cable and plug)- Interface cable for PC programming- Bluetooth adapter The variant "Frequency inverter with membrane keypad" offers the possibility to directly control the FI,such as Start-stop, left-right-run etc.For parameterization, one of the following options must also be ordered:: - External HMI device (MMI with cable and plug)- Interface cable for PC programming- Bluetooth adapter The variant "Frequency converter with MMI operating unit" does not require an optional operating unitIn addition, a display is included in the device cover. The mentioned options can be used if required.     Important notesThis drive is a custom-made product. A withdrawal or cancellation of the purchase is excluded!All product photos are non-binding examples!

Worm Gear Motor, Power= 3 KW, Speed= 9 to 110 rpmDegree of protection= IP55, Insulation class= F (155°C), Operating mode= S1, Type of duty= S1- 100%,Hollow shaft= 42mm, Mounting position= M1-M6. Engine Speed= 4 pole, Ratio (i)= 15, Torque= 264 Nm,Service factor (f.s.)= 2,5 . Terminal box= top (rotatable), Weight= 64 kg , Paint= RAL 5010 (gentian blue),Temperature sensor= 3 x PTC-thermistors, Housing= Aluminum or cast iron, Ball bearings= SKF, C & U or equivalent, When ordering, please select the desired mounting position and design! Frequency Inverter Power= 3.0 KW, Size= B, Input Voltage= 3 x 400V + 10% (three-phase), Input frequency= 50/60 Hz, Output frequency= 0-400 Hz, EMC filter= C2, Degree of protection= IP65, Dimensions= 270mm x 189mm x 140mm, Mains current (input)= 6.2 A. Ideal control range= 5-60 Hz, below 30 Hz, a forced cooling fan is used for cooling needed. Product Information The frequency converter optionally offers the possibility of becoming "bus-capable" with the aid of fieldbus modules. With CANopen, EtherCAT, Modbus (already included), Profibus, Profinet and Sercos the EASYdrive offers Compatibility with almost all common interfaces. The customer can choose the relevant bus system for him and integrate the EASYdrive ideally in the control environment of its application.The required optional control variant must be specified for orders.The EASYdrive lasts without external filter measures the EMC class C2 (for 3-phase mains supply), or C1 (for 1-phase mains supply).   ! Possible variant selection!      Product selection When selecting the frequency converter, make sure that there are 3 variants. First, this includes the devicein the standard version, secondly the device with a membrane keyboard and thirdly the device with an MMI operating unit.The illustrated "frequency converter in standard version" is fully usable and contains a built-in potentiometer,but needs to control a corresponding control panel.For this purpose, one of the following options must be ordered: - External HMI device (MMI with cable and plug)- Interface cable for PC programming- Bluetooth adapter The variant "Frequency inverter with membrane keypad" offers the possibility to directly control the FI,such as Start-stop, left-right-run etc.For parameterization, one of the following options must also be ordered::- External HMI device (MMI with cable and plug)- Interface cable for PC programming- Bluetooth adapter The variant "Frequency converter with MMI operating unit" does not require an optional operating unitIn addition, a display is included in the device cover. The mentioned options can be used if required.    Important notesThis drive is a custom-made product. A withdrawal or cancellation of the purchase is excluded!All product photos are non-binding examples!

Worm Gear Motor, Power= 3 KW, Speed= 7 to 84 rpmDegree of protection= IP55, Insulation class= F (155°C), Operating mode= S1, Type of duty= S1- 100%,Hollow shaft= 42mm, Mounting position= M1-M6. Engine Speed= 4 pole, Ratio (i)= 20, Torque= 348 Nm,Service factor (f.s.)= 1,9 . Terminal box= top (rotatable), Weight= 64 kg , Paint= RAL 5010 (gentian blue),Temperature sensor= 3 x PTC-thermistors, Housing= Aluminum or cast iron, Ball bearings= SKF, C & U or equivalent, When ordering, please select the desired mounting position and design! Frequency Inverter Power= 3.0 KW, Size= B, Input Voltage= 3 x 400V + 10% (three-phase), Input frequency= 50/60 Hz, Output frequency= 0-400 Hz, EMC filter= C2, Degree of protection= IP65, Dimensions= 270mm x 189mm x 140mm, Mains current (input)= 6.2 A. Ideal control range= 5-60 Hz, below 30 Hz, a forced cooling fan is used for cooling needed. Product Information The frequency converter optionally offers the possibility of becoming "bus-capable" with the aid of fieldbus modules. With CANopen, EtherCAT, Modbus (already included), Profibus, Profinet and Sercos the EASYdrive offers Compatibility with almost all common interfaces. The customer can choose the relevant bus system for him and integrate the EASYdrive ideally in the control environment of its application.The required optional control variant must be specified for orders.The EASYdrive lasts without external filter measures the EMC class C2 (for 3-phase mains supply), or C1 (for 1-phase mains supply).   ! Possible variant selection!      Product selection When selecting the frequency converter, make sure that there are 3 variants. First, this includes the devicein the standard version, secondly the device with a membrane keyboard and thirdly the device with an MMI operating unit.The illustrated "frequency converter in standard version" is fully usable and contains a built-in potentiometer,but needs to control a corresponding control panel.For this purpose, one of the following options must be ordered: - External HMI device (MMI with cable and plug)- Interface cable for PC programming- Bluetooth adapter The variant "Frequency inverter with membrane keypad" offers the possibility to directly control the FI,such as Start-stop, left-right-run etc.For parameterization, one of the following options must also be ordered::- External HMI device (MMI with cable and plug)- Interface cable for PC programming- Bluetooth adapter The variant "Frequency converter with MMI operating unit" does not require an optional operating unitIn addition, a display is included in the device cover. The mentioned options can be used if required.    Important notesThis drive is a custom-made product. A withdrawal or cancellation of the purchase is excluded!All product photos are non-binding examples!