Worm variable speed gear motor, Power= 1.1 kW, Speed= 4 - 20 rpm, Voltage= 3 x 230/400 V-50 Hz, 3 x 265/460 V-60 Hz (± 5% according to VDE 0530), Protection type= IP55, iso class= F (155°C), Operating mode= S1, Duty cycle= S1- 100%, Total length= approx. 732 mm, Hollow shaft = 42 mm, motor speed = 4 poles, translation with adjustment unit (i) = 70 - 350 Transmission only worm gear (i) = 50, torque = 320 Nm - 550 Nm, service factor ( f.s.)= 1, terminal box= above (rotatable), weight= 21 kg, color= RAL 5010 (gentian blue), temperature sensor= 3 x PTC thermistor, gear housing = aluminum, ball bearing = SKF, C&U or equivalent, Cooling= axial fan (plastic). For technical reasons, the variable speed worm gear motor should cannot be operated with a frequency converter. The drive corresponds to IEC 60034-30:2008, is suitable for both directions of rotation and is supplied with an oil filling. Open hollow shafts are to be sealed with a cover cap. This can be ordered under the heading "Accessories". In accordance with VDE 0105 and IEC 364, all work on the electric drive may only be carried out by qualified personnel. As usual with variable speed gears, speed control by turning the handwheel is only permitted during operation! A change in speed while stationary can damage the stepless adjustment unit. All product photos are non-binding examples! Technical changes reserved.

Worm variable speed gear motor, Power= 1.1 kW, Speed= 2 - 10 rpm, Voltage= 3 x 230/400 V-50 Hz, 3 x 265/460 V-60 Hz (± 5% according to VDE 0530), Protection type= IP55, iso class= F (155°C), Operating mode= S1, Duty cycle= S1- 100%, Total length= approx. 732 mm, Hollow shaft= 42 mm, motor Speed= 4 poles, gear ratio with adjustment unit (i)= 140 - 700 Gear ratio only worm gear (i)= 100, torque= 522 Nm - 710 Nm, service factor ( f.s.)= 1, terminal box= above (rotatable), weight= 21 kg, color= RAL 5010 (gentian blue), temperature sensor= 3 x PTC thermistor, gear housing = aluminum, ball bearing = SKF, C&U or equivalent, Cooling= axial fan (plastic). For technical reasons, the variable speed worm gear motor should cannot be operated with a frequency converter. The drive corresponds to IEC 60034-30:2008, is suitable for both directions of rotation and is supplied with an oil filling. Open hollow shafts are to be sealed with a cover cap. This can be ordered under the heading "Accessories". In accordance with VDE 0105 and IEC 364, all work on the electric drive may only be carried out by qualified personnel. As usual with variable speed gears, speed control by turning the handwheel is only permitted during operation! A change in speed while stationary can damage the stepless adjustment unit. All product photos are non-binding examples! Technical changes reserved.

Worm variable speed gear motor, Power= 1.1 kW, Speed= 3.5 - 17 rpm, Voltage= 3 x 230/400 V-50 Hz, 3 x 265/460 V-60 Hz (± 5% according to VDE 0530), Protection type= IP55, iso class= F (155°C), Operating mode= S1, Duty cycle= S1- 100%, Total length= approx. 732 mm, Hollow shaft= 42 mm, motor Speed= 4 poles, gear ratio with adjustment unit (i)= 84 - 420 Gear ratio only worm gear (i)= 60, torque= 368 Nm - 625 Nm, operating factor ( f.s.)= 1, terminal box= above (rotatable), weight= 21 kg, color= RAL 5010 (gentian blue), temperature sensor= 3 x PTC thermistor, gear housing = aluminum, ball bearing = SKF, C&U or equivalent, Cooling= axial fan (plastic). For technical reasons, the variable speed worm gear motor should cannot be operated with a frequency converter. The drive corresponds to IEC 60034-30:2008, is suitable for both directions of rotation and is supplied with an oil filling. Open hollow shafts are to be sealed with a cover cap. This can be ordered under the heading "Accessories". In accordance with VDE 0105 and IEC 364, all work on the electric drive may only be carried out by qualified personnel. As usual with variable speed gears, speed control by turning the hand wheel is only permitted during operation! A change in speed while stationary can damage the stepless adjustment unit. All product photos are non-binding examples! Technical changes reserved.

Worm variable speed gear motor, Power= 1.5 kW, Speed= 3.5 - 16.5 rpm, Voltage= 3 x 230/400 V-50 Hz, 3 x 265/460 V-60 Hz (± 5% according to VDE 0530), Protection type= IP55, iso class= F (155°C), Operating mode= S1, Duty cycle= S1- 100%, Total length= approx. 757 mm, Hollow shaft = 42 mm, motor speed = 4 poles, translation with adjustment unit (i) = 84 - 420 Transmission only worm gear (i) = 60, torque = 490 Nm - 833 Nm, operating factor ( f.s.)= 1, terminal box= above (rotatable), weight= 21 kg, color= RAL 5010 (gentian blue), temperature sensor= 3 x PTC thermistor, gear housing = aluminum, ball bearing = SKF, C&U or equivalent, Cooling= axial fan (plastic). For technical reasons, the variable speed worm gear motor should cannot be operated with a frequency converter. The drive corresponds to IEC 60034-30:2008, is suitable for both directions of rotation and is supplied with an oil filling. Open hollow shafts are to be sealed with a cover cap. This can be ordered under the heading "Accessories". In accordance with VDE 0105 and IEC 364, all work on the electric drive may only be carried out by qualified personnel. As usual with variable speed gears, speed control by turning the handwheel is only permitted during operation! A change in speed while stationary can damage the stepless adjustment unit. All product photos are non-binding examples! Technical changes reserved.

Worm variable speed gear motor, Power= 1.5 kW, Speed= 4 - 20 rpm, Voltage= 3 x 230/400 V-50 Hz, 3 x 265/460 V-60 Hz (± 5% according to VDE 0530), Protection type= IP55, iso class= F (155°C), Operating mode= S1, Duty cycle= S1- 100%, Total length= approx. 757 mm, Hollow shaft = 42 mm, motor speed = 4 poles, translation with adjustment unit (i) = 70 - 350 Transmission only worm gear (i) = 50, torque = 426 Nm - 733 Nm, operating factor ( f.s.)= 1, terminal box= above (rotatable), weight= 21 kg, color= RAL 5010 (gentian blue), temperature sensor= 3 x PTC thermistor, gear housing = aluminum, ball bearing = SKF, C&U or equivalent, Cooling= axial fan (plastic). For technical reasons, the variable speed worm gear motor should cannot be operated with a frequency converter. The drive corresponds to IEC 60034-30:2008, is suitable for both directions of rotation and is supplied with an oil filling. Open hollow shafts are to be sealed with a cover cap. This can be ordered under the heading "Accessories". In accordance with VDE 0105 and IEC 364, all work on the electric drive may only be carried out by qualified personnel. As usual with variable speed gears, speed control by turning the handwheel is only permitted during operation! A change in speed while stationary can damage the stepless adjustment unit. All product photos are non-binding examples! Technical changes reserved.

Worm variable speed gear motor, power= 2.2 kW, speed= 20 – 100 rpm Voltage= 3 x 230/400 V-50 Hz, 3 x 265/460 V-60 Hz (± 5% in accordance with VDE 0530), Protection class= IP55, insulation class= F (155°C), operating mode= S1, duty cycle= S1- 100%, total length= approx. 835 mm, Hollow shaft= 42 mm, motor speed= 4 pole, gear ratio with adjustment unit (i)= 14 – 70 Gear ratio only worm gear (i)= 10, torque= 157 Nm – 294 Nm, operating factor (f.s.)= 1, Terminal box = top (rotatable), weight = 22 kg, color = RAL 5010 (gentian blue), Temperature sensor = 3 x PTC thermistors, gear housing = aluminum, ball bearings = SKF, C&U or equivalent, Cooling = axial fan (plastic). The drive complies with IEC 60034-30:2008, is suitable for both directions of rotation and is supplied with an oil filling. Open hollow shafts must be closed with a cover cap. This can be ordered under the "Accessories" section. In accordance with VDE 0105 or. According to IEC 364, all work on the electric drive must only be carried out by qualified specialist personnel. As is usual with variable speed drives, speed control by turning the handwheel is only permitted during operation! A speed change when the drive is at a standstill can lead to damage to the stepless adjustment unit. All product photos are non-binding examples! Technical changes reserved.

Worm variable speed gear motor, power= 2.2 kW, speed= 13.5 – 66.5 rpm Voltage= 3 x 230/400 V-50 Hz, 3 x 265/460 V-60 Hz (± 5% in accordance with VDE 0530), Protection class= IP55, insulation class= F (155°C), operating mode= S1, duty cycle= S1- 100%, total length= approx. 835 mm, Hollow shaft= 42 mm, motor speed= 4 pole, gear ratio with adjustment unit (i)= 21 – 105 Gear ratio only worm gear (i)= 15, torque= 228 Nm – 418 Nm, operating factor (f.s.)= 1, Terminal box = top (rotatable), weight = 22 kg, color = RAL 5010 (gentian blue), Temperature sensor = 3 x PTC thermistors, gear housing = aluminum, ball bearings = SKF, C&U or equivalent, Cooling = axial fan (plastic). The drive complies with IEC 60034-30:2008, is suitable for both directions of rotation and is supplied with an oil filling. Open hollow shafts must be closed with a cover cap. This can be ordered under the "Accessories" section. In accordance with VDE 0105 or. According to IEC 364, all work on the electric drive must only be carried out by qualified specialist personnel. As is usual with variable speed drives, speed control by turning the handwheel is only permitted during operation! A speed change when the drive is at a standstill can lead to damage to the stepless adjustment unit. All product photos are non-binding examples! Technical changes reserved.

Worm variable speed gear motor, power= 2.2 kW, speed= 10 – 50 rpm Voltage= 3 x 230/400 V-50 Hz, 3 x 265/460 V-60 Hz (± 5% in accordance with VDE 0530), Protection class= IP55, insulation class= F (155°C), operating mode= S1, duty cycle= S1- 100%, total length= approx. 835 mm, Hollow shaft= 42 mm, motor speed= 4 pole, gear ratio with adjustment unit (i)= 28 – 140 Gear ratio only worm gear (i)= 20, torque= 298 Nm – 549 Nm, operating factor (f.s.)= 1, Terminal box = top (rotatable), weight = 22 kg, color = RAL 5010 (gentian blue), Temperature sensor = 3 x PTC thermistors, gear housing = aluminum, ball bearings = SKF, C&U or equivalent, Cooling = axial fan (plastic). The drive complies with IEC 60034-30:2008, is suitable for both directions of rotation and is supplied with an oil filling. Open hollow shafts must be closed with a cover cap. This can be ordered under the "Accessories" section. In accordance with VDE 0105 or. According to IEC 364, all work on the electric drive must only be carried out by qualified specialist personnel. As is usual with variable speed drives, speed control by turning the handwheel is only permitted during operation! A speed change when the drive is at a standstill can lead to damage to the stepless adjustment unit. All product photos are non-binding examples! Technical changes reserved.

Worm variable speed gear motor, Power= 2.2 kW, Speed= 27 – 133 rpm Voltage= 3 x 230/400 V-50 Hz, 3 x 265/460 V-60 Hz (± 5% in accordance with VDE 0530), Protection class= IP55, insulation class= F (155°C), operating mode= S1, duty cycle= S1- 100%, total length= approx. 835 mm, Hollow shaft= 42 mm, motor speed= 4 pole, gear ratio with adjustment unit (i)= 10.5 – 52.5 Gear ratio only worm gear (i)= 7.5, torque= 120 Nm – 226 Nm, operating factor (f.s.)= 1, Terminal box = top (rotatable), weight = 22 kg, color = RAL 5010 (gentian blue), Temperature sensor = 3 x PTC thermistors, gear housing = aluminum, ball bearings = SKF, C&U or equivalent, Cooling = axial fan (plastic). The drive complies with IEC 60034-30:2008, is suitable for both directions of rotation and is supplied with an oil filling. Open hollow shafts must be closed with a cover cap. This can be ordered under the "Accessories" section. In accordance with VDE 0105 or. According to IEC 364, all work on the electric drive must only be carried out by qualified specialist personnel. As is usual with variable speed drives, speed control by turning the handwheel is only permitted during operation! A speed change when the drive is at a standstill can lead to damage to the stepless adjustment unit. All product photos are non-binding examples! Technical changes reserved.

Worm variable speed gear motor, Power= 2.2 kW, Speed= 8 – 40 rpm Voltage= 3 x 230/400 V-50 Hz, 3 x 265/460 V-60 Hz (± 5% in accordance with VDE 0530), Protection class= IP55, insulation class= F (155°C), operating mode= S1, duty cycle= S1- 100%, total length= approx. 835 mm, Hollow shaft= 42 mm, motor speed= 4 pole, gear ratio with adjustment unit (i)= 35 – 175, Gear ratio only worm gear (i)= 25, torque= 364 Nm – 664 Nm, operating factor (f.s.)= 1, Terminal box = top (rotatable), weight = 22 kg, color = RAL 5010 (gentian blue), Temperature sensor = 3 x PTC thermistors, gear housing = aluminum, ball bearings = SKF, C&U or equivalent, Cooling = axial fan (plastic). The drive complies with IEC 60034-30:2008, is suitable for both directions of rotation and is supplied with an oil filling. Open hollow shafts must be closed with a cover cap. This can be ordered under the "Accessories" section. In accordance with VDE 0105 or. According to IEC 364, all work on the electric drive must only be carried out by qualified specialist personnel. As is usual with variable speed drives, speed control by turning the handwheel is only permitted during operation! A speed change when the drive is at a standstill can lead to damage to the stepless adjustment unit. All product photos are non-binding examples! Technical changes reserved.

Worm variable speed gear motor, Power= 2.2 kW, Speed= 7 – 33 rpm Voltage= 3 x 230/400 V-50 Hz, 3 x 265/460 V-60 Hz (± 5% in accordance with VDE 0530), Protection class= IP55, insulation class= F (155°C), operating mode= S1, duty cycle= S1- 100%, total length= approx. 835 mm, Hollow shaft= 42 mm, motor speed= 4 pole, gear ratio with adjustment unit (i)= 42 – 210, Gear ratio only worm gear (i)= 30, torque= 413 Nm – 717 Nm, operating factor (f.s.)= 1, Terminal box= top (rotatable), weight= 22 kg, color= RAL 5010 (gentian blue), Temperature sensor= 3 x PTC thermistors, gear housing= aluminum, ball bearings= SKF, C&U or equivalent, Cooling= axial fan (plastic). The drive complies with IEC 60034-30:2008, is suitable for both directions of rotation and is supplied with an oil filling. Open hollow shafts must be closed with a cover cap. This can be ordered under the "Accessories" section. In accordance with VDE 0105 or. According to IEC 364, all work on the electric drive must only be carried out by qualified specialist personnel. As is usual with variable speed drives, speed control by turning the handwheel is only permitted during operation! A speed change when the drive is at a standstill can lead to damage to the stepless adjustment unit. All product photos are non-binding examples! Technical changes reserved.

Worm variable speed gear motor, Power= 2.2 kW, Speed= 5 – 25 rpm Voltage= 3 x 230/400 V-50 Hz, 3 x 265/460 V-60 Hz (± 5% in accordance with VDE 0530), Protection class= IP55, insulation class= F (155°C), operating mode= S1, duty cycle= S1- 100%, total length= approx. 835 mm, Hollow shaft= 42 mm, motor speed= 4 pole, gear ratio with adjustment unit (i)= 56 – 280, Gear ratio only worm gear (i)= 40, torque= 533 Nm – 931 Nm, operating factor (f.s.)= 1, Terminal box= top (rotatable), weight= 22 kg, color= RAL 5010 (gentian blue), Temperature sensor= 3 x PTC thermistors, gear housing= aluminum, ball bearings= SKF, C&U or equivalent, Cooling= axial fan (plastic). The drive complies with IEC 60034-30:2008, is suitable for both directions of rotation and is supplied with an oil filling. Open hollow shafts must be closed with a cover cap. This can be ordered under the "Accessories" section. In accordance with VDE 0105 or. According to IEC 364, all work on the electric drive must only be carried out by qualified specialist personnel. As is usual with variable speed drives, speed control by turning the handwheel is only permitted during operation! A speed change when the drive is at a standstill can lead to damage to the stepless adjustment unit. All product photos are non-binding examples! Technical changes reserved.

Worm variable speed gear motor, power= 3.0 kW, speed= 8 – 40 rpm Voltage= 3 x 230/400 V-50 Hz, 3 x 265/460 V-60 Hz (± 5% in accordance with VDE 0530), Protection class= IP55, insulation class= F (155°C), operating mode= S1, duty cycle= S1- 100%, total length= approx. 835 mm, Hollow shaft= 42 mm, motor speed= 4 pole, gear ratio with adjustment unit (i)= 35 – 175, Gear ratio only worm gear (i)= 25, torque= 485 Nm – 885 Nm, operating factor (f.s.)= 1, Terminal box= top (rotatable), weight= 22 kg, color= RAL 5010 (gentian blue), Temperature sensor= 3 x PTC thermistors, gear housing= aluminum, ball bearings= SKF, C&U or equivalent, Cooling= axial fan (plastic). The drive complies with IEC 60034-30:2008, is suitable for both directions of rotation and is supplied with an oil filling. Open hollow shafts must be closed with a cover cap. This can be ordered under the "Accessories" section. In accordance with VDE 0105 or. According to IEC 364, all work on the electric drive must only be carried out by qualified specialist personnel. As is usual with variable speed drives, speed control by turning the handwheel is only permitted during operation! A speed change when the drive is at a standstill can lead to damage to the stepless adjustment unit. All product photos are non-binding examples! Technical changes reserved.

Worm variable speed gear motor, power= 3.0 kW, speed= 27 – 133 rpm Voltage= 3 x 230/400 V-50 Hz, 3 x 265/460 V-60 Hz (± 5% in accordance with VDE 0530), Protection class= IP55, insulation class= F (155°C), operating mode= S1, duty cycle= S1- 100%, total length= approx. 835 mm, Hollow shaft= 42 mm, motor speed= 4 pole, gear ratio with adjustment unit (i)= 10.5 – 52.5, Gear ratio only worm gear (i)= 7.5, torque= 160 Nm – 302 Nm, operating factor (f.s.)= 1, Terminal box= top (rotatable), weight= 22 kg, color= RAL 5010 (gentian blue), Temperature sensor= 3 x PTC thermistors, gear housing= aluminum, ball bearings= SKF, C&U or equivalent, Cooling= axial fan (plastic). The drive complies with IEC 60034-30:2008, is suitable for both directions of rotation and is supplied with an oil filling. Open hollow shafts must be closed with a cover cap. This can be ordered under the "Accessories" section. In accordance with VDE 0105 or. According to IEC 364, all work on the electric drive must only be carried out by qualified specialist personnel. As is usual with variable speed drives, speed control by turning the handwheel is only permitted during operation! A speed change when the drive is at a standstill can lead to damage to the stepless adjustment unit. All product photos are non-binding examples! Technical changes reserved.

Worm variable speed gear motor, power= 3.0 kW, speed= 20 – 100 rpm Voltage= 3 x 230/400 V-50 Hz, 3 x 265/460 V-60 Hz (± 5% in accordance with VDE 0530), Protection class= IP55, insulation class= F (155°C), operating mode= S1, duty cycle= S1- 100%, total length= approx. 835 mm, Hollow shaft= 42 mm, motor speed= 4 pole, gear ratio with adjustment unit (i)= 14 – 70, Gear ratio only worm gear (i)= 10, torque= 210 Nm – 392 Nm, operating factor (f.s.)= 1, Terminal box= top (rotatable), weight= 22 kg, color= RAL 5010 (gentian blue), Temperature sensor= 3 x PTC thermistors, gear housing= aluminum, ball bearings= SKF, C&U or equivalent, Cooling= axial fan (plastic). The drive complies with IEC 60034-30:2008, is suitable for both directions of rotation and is supplied with an oil filling. Open hollow shafts must be closed with a cover cap. This can be ordered under the "Accessories" section. In accordance with VDE 0105 or. According to IEC 364, all work on the electric drive must only be carried out by qualified specialist personnel. As is usual with variable speed drives, speed control by turning the handwheel is only permitted during operation! A speed change when the drive is at a standstill can lead to damage to the stepless adjustment unit. All product photos are non-binding examples! Technical changes reserved.

Worm variable speed gear motor, Power= 3.0 kW, Speed= 5 – 25 rpm Voltage= 3 x 230/400 V-50 Hz, 3 x 265/460 V-60 Hz (± 5% in accordance with VDE 0530), Protection class= IP55, insulation class= F (155°C), operating mode= S1, duty cycle= S1- 100%, total length= approx. 835 mm, Hollow shaft= 42 mm, motor speed= 4 pole, gear ratio with adjustment unit (i)= 56 – 280,Gear ratio only worm gear (i)= 40, torque= 711 Nm – 1030 Nm, operating factor (f.s.)= 1, Terminal box= top (rotatable), weight= 22 kg, color= RAL 5010 (gentian blue), Temperature sensor= 3 x PTC thermistors, gear housing= aluminum, ball bearings= SKF, C&U or equivalent, Cooling= axial fan (plastic). The drive complies with IEC 60034-30:2008, is suitable for both directions of rotation and is supplied with an oil filling. Open hollow shafts must be closed with a cover cap. This can be ordered under the "Accessories" section. In accordance with VDE 0105 or. According to IEC 364, all work on the electric drive must only be carried out by qualified specialist personnel. As is usual with variable speed drives, speed control by turning the handwheel is only permitted during operation! A speed change when the drive is at a standstill can lead to damage to the stepless adjustment unit. All product photos are non-binding examples! Technical changes reserved.

Worm variable speed gear motor, power= 3.0 kW, speed= 7 – 33 rpm Voltage= 3 x 230/400 V-50 Hz, 3 x 265/460 V-60 Hz (± 5% in accordance with VDE 0530), Protection class= IP55, insulation class= F (155°C), operating mode= S1, duty cycle= S1- 100%, total length= approx. 835 mm, Hollow shaft= 42 mm, motor speed= 4 pole, gear ratio with adjustment unit (i)= 42 – 210, Gear ratio only worm gear (i)= 30, torque= 547 Nm – 956 Nm, operating factor (f.s.)= 1, Terminal box= top (rotatable), weight= 22 kg, color= RAL 5010 (gentian blue), Temperature sensor= 3 x PTC thermistors, gear housing= aluminum, ball bearings= SKF, C&U or equivalent, Cooling= axial fan (plastic). The drive complies with IEC 60034-30:2008, is suitable for both directions of rotation and is supplied with an oil filling. Open hollow shafts must be closed with a cover cap. This can be ordered under the "Accessories" section. In accordance with VDE 0105 or. According to IEC 364, all work on the electric drive must only be carried out by qualified specialist personnel. As is usual with variable speed drives, speed control by turning the handwheel is only permitted during operation! A speed change when the drive is at a standstill can lead to damage to the stepless adjustment unit. All product photos are non-binding examples! Technical changes reserved.

Worm variable speed gear motor, power= 3.0 kW, speed= 10 – 50 rpm Voltage= 3 x 230/400 V-50 Hz, 3 x 265/460 V-60 Hz (± 5% in accordance with VDE 0530), Protection class= IP55, insulation class= F (155°C), operating mode= S1, duty cycle= S1- 100%, total length= approx. 835 mm, Hollow shaft= 42 mm, motor speed= 4 pole, gear ratio with adjustment unit (i)= 28 – 140, Gear ratio only worm gear (i)= 20, torque= 398 Nm – 732 Nm, operating factor (f.s.)= 1, Terminal box= top (rotatable), weight= 22 kg, color= RAL 5010 (gentian blue), Temperature sensor= 3 x PTC thermistors, gear housing= aluminum, ball bearings= SKF, C&U or equivalent, Cooling= axial fan (plastic). The drive complies with IEC 60034-30:2008, is suitable for both directions of rotation and is supplied with an oil filling. Open hollow shafts must be closed with a cover cap. This can be ordered under the "Accessories" section. In accordance with VDE 0105 or. According to IEC 364, all work on the electric drive must only be carried out by qualified specialist personnel. As is usual with variable speed drives, speed control by turning the handwheel is only permitted during operation! A speed change when the drive is at a standstill can lead to damage to the stepless adjustment unit. All product photos are non-binding examples! Technical changes reserved.

Worm variable speed gear motor, power= 3.0 kW, speed= 13.5 – 66.5 rpm Voltage= 3 x 230/400 V-50 Hz, 3 x 265/460 V-60 Hz (± 5% in accordance with VDE 0530), Protection class= IP55, insulation class= F (155°C), operating mode= S1, duty cycle= S1- 100%, total length= approx. 835 mm, Hollow shaft= 42 mm, motor speed= 4 pole, gear ratio with adjustment unit (i)= 21 – 105, Gear ratio only worm gear (i)= 15, torque= 304 Nm – 558 Nm, operating factor (f.s.)= 1, Terminal box= top (rotatable), weight= 22 kg, color= RAL 5010 (gentian blue), Temperature sensor= 3 x PTC thermistors, gear housing= aluminum, ball bearings= SKF, C&U or equivalent, Cooling= axial fan (plastic). The drive complies with IEC 60034-30:2008, is suitable for both directions of rotation and is supplied with an oil filling. Open hollow shafts must be closed with a cover cap. This can be ordered under the "Accessories" section. In accordance with VDE 0105 or. According to IEC 364, all work on the electric drive must only be carried out by qualified specialist personnel. As is usual with variable speed drives, speed control by turning the handwheel is only permitted during operation! A speed change when the drive is at a standstill can lead to damage to the stepless adjustment unit. All product photos are non-binding examples! Technical changes reserved.