Worm variable speed gear motor, Power= 0.75 kW, Speed= 4 – 20 rpm, Voltage= 3 x 230/400 V-50 Hz, 3 x 265/460 V-60 Hz (± 5% according to VDE 0530), Protection type= IP55, iso class= F (155°C), Operating mode= S1, Duty cycle= S1- 100%, Total length= approx. 566 mm, Hollow shaft = 25 mm, motor speed = 4 poles, translation with adjustment unit (i) = 70 - 350 Transmission only worm gear (i) = 50, torque = 185 Nm - 310 Nm, service factor ( f.s.)= 1, terminal box= above (rotatable), weight= 18 kg, color= RAL 5010 (gentian blue), temperature sensor= 3 x PTC thermistors, gear housing = aluminum, ball bearing = SKF, C&U or equivalent, Cooling= axial fan (plastic). For technical reasons, the variable speed worm gear motor should cannot be operated with a frequency converter. The drive corresponds to IEC 60034-30:2008, is suitable for both directions of rotation and is supplied with an oil filling. Open hollow shafts are to be sealed with a cover cap. This can be ordered under the heading "Accessories". According to VDE 0105 and IEC 364, all work on the electric drive may only be carried out by qualified personnel. As usual with variable speed gears, speed control by turning the handwheel is only permitted during operation! A change in speed while stationary can damage the stepless adjustment unit. All product photos are non-binding examples! Technical changes reserved.

Worm variable speed gear motor, Power= 0.75 kW, Speed= 7 – 33 rpm, Voltage= 3 x 230/400 V-50 Hz, 3 x 265/460 V-60 Hz (± 5% according to VDE 0530), Protection type= IP55, iso class= F (155°C), Operating mode= S1, Duty cycle= S1- 100%, Total length= approx. 566 mm, Hollow shaft= 25 mm, motor Speed= 4 poles, gear ratio with adjustment unit (i)= 42 – 210 Gear ratio only worm gear (i)= 30, torque= 126 Nm – 219 Nm, operating factor ( f.s.)= 1, terminal box= above (rotatable), weight= 18 kg, color= RAL 5010 (gentian blue), temperature sensor= 3 x PTC thermistors, gear housing = aluminum, ball bearing = SKF, C&U or equivalent, Cooling= axial fan (plastic). For technical reasons, the variable speed worm gear motor should cannot be operated with a frequency converter. The drive corresponds to IEC 60034-30:2008, is suitable for both directions of rotation and is supplied with an oil filling. Open hollow shafts are to be sealed with a cover cap. This can be ordered under the heading "Accessories". According to VDE 0105 and IEC 364, all work on the electric drive may only be carried out by qualified personnel. As usual with variable speed gears, speed control by turning the handwheel is only permitted during operation! A change in speed while stationary can damage the stepless adjustment unit. All product photos are non-binding examples! Technical changes reserved.

Worm variable speed gear motor, Power= 0.75 kW, Speed= 5 – 25 rpm, Voltage= 3 x 230/400 V-50 Hz, 3 x 265/460 V-60 Hz (± 5% according to VDE 0530), Protection type= IP55, iso class= F (155°C), Operating mode= S1, Duty cycle= S1- 100%, Total length= approx. 566 mm, Hollow shaft = 25 mm, motor speed = 4 poles, translation with adjustment unit (i) = 56 - 280 Transmission only worm gear (i) = 40, torque = 156 Nm - 232 Nm, operating factor ( f.s.)= 1, terminal box= above (rotatable), weight= 18 kg, color= RAL 5010 (gentian blue), temperature sensor= 3 x PTC thermistors, gear housing = aluminum, ball bearing = SKF, C&U or equivalent, Cooling= axial fan (plastic). For technical reasons, the variable speed worm gear motor should cannot be operated with a frequency converter. The drive corresponds to IEC 60034-30:2008, is suitable for both directions of rotation and is supplied with an oil filling. Open hollow shafts are to be sealed with a cover cap. This can be ordered under the heading "Accessories". According to VDE 0105 and IEC 364, all work on the electric drive may only be carried out by qualified personnel. As usual with variable speed gears, speed control by turning the handwheel is only permitted during operation! A change in speed while stationary can damage the stepless adjustment unit. All product photos are non-binding examples! Technical changes reserved.

Worm variable speed gear motor, Power= 0.75 kW, Speed= 10 – 50 rpm, Voltage= 3 x 230/400 V-50 Hz, 3 x 265/460 V-60 Hz (± 5% according to VDE 0530), Protection type= IP55, iso class= F (155°C), Operating mode= S1, Duty cycle= S1- 100%, Total length= approx. 566 mm, Hollow shaft = 25 mm, motor speed = 4 poles, translation with adjustment unit (i) = 28 - 140 Transmission only worm gear (i) = 20, torque = 92 Nm - 168 Nm, service factor ( f.s.)= 1, terminal box= above (rotatable), weight= 18 kg, color= RAL 5010 (gentian blue), temperature sensor= 3 x PTC thermistors, gear housing = aluminum, ball bearing = SKF, C&U or equivalent, Cooling= axial fan (plastic). For technical reasons, the variable speed worm gear motor should cannot be operated with a frequency converter. The drive corresponds to IEC 60034-30:2008, is suitable for both directions of rotation and is supplied with an oil filling. Open hollow shafts are to be sealed with a cover cap. This can be ordered under the heading "Accessories". According to VDE 0105 and IEC 364, all work on the electric drive may only be carried out by qualified personnel. As usual with variable speed gears, speed control by turning the handwheel is only permitted during operation! A change in speed while stationary can damage the stepless adjustment unit. All product photos are non-binding examples! Technical changes reserved.

Worm variable speed gear motor, Power= 0.75 kW, Speed= 20 – 100 rpm, Voltage= 3 x 230/400 V-50 Hz, 3 x 265/460 V-60 Hz (± 5% according to VDE 0530), Protection type= IP55, iso class= F (155°C), Operating mode= S1, Duty cycle= S1- 100%, Total length= approx. 566 mm, Hollow shaft= 25 mm, motor Speed= 4 poles, gear ratio with adjustment unit (i)= 14 - 70 Gear ratio only worm gear (i)= 10, torque= 51 Nm - 94 Nm, service factor ( f.s.)= 1, terminal box= above (rotatable), weight= 18 kg, color= RAL 5010 (gentian blue), temperature sensor= 3 x PTC thermistors, gear housing = aluminum, ball bearing = SKF, C&U or equivalent, Cooling= axial fan (plastic). For technical reasons, the variable speed worm gear motor should cannot be operated with a frequency converter. The drive corresponds to IEC 60034-30:2008, is suitable for both directions of rotation and is supplied with an oil filling. Open hollow shafts are to be sealed with a cover cap. This can be ordered under the heading "Accessories". According to VDE 0105 and IEC 364, all work on the electric drive may only be carried out by qualified personnel. As usual with variable speed gears, speed control by turning the handwheel is only permitted during operation! A change in speed while stationary can damage the stepless adjustment unit. All product photos are non-binding examples! Technical changes reserved.

Worm variable speed gear motor, Power= 0.75 kW, Speed= 27 - 133 rpm, Voltage= 3 x 230/400 V-50 Hz, 3 x 265/460 V-60 Hz (± 5% according to VDE 0530), Protection type= IP55, iso class= F (155°C), Operating mode= S1, Duty cycle= S1- 100%, Total length= approx. 566 mm, Hollow shaft = 25 mm, motor speed = 4 poles, translation with adjustment unit (i) = 10.5 - 52.5 Transmission only worm gear (i) = 7.5, torque = 39 Nm – 73 Nm, service factor (f.s.)= 1, terminal box= above (rotatable), weight= 18 kg, color= RAL 5010 (gentian blue), temperature sensor= 3 x PTC thermistors, gearbox housing = aluminium, ball bearings = SKF, C&U or equivalent, Cooling= axial fan (plastic). For technical reasons, the variable speed worm gear motor should cannot be operated with a frequency converter. The drive corresponds to IEC 60034-30:2008, is suitable for both directions of rotation and is supplied with an oil filling. Open hollow shafts are to be sealed with a cover cap. This can be ordered under the heading "Accessories". According to VDE 0105 and IEC 364, all work on the electric drive may only be carried out by qualified personnel. As usual with variable speed gears, speed control by turning the hand wheel is only permitted during operation! A change in speed while stationary can damage the stepless adjustment unit. All product photos are non-binding examples! Technical changes reserved.

Worm variable speed gear motor, Power= 0.55 kW, Speed= 4 - 20 rpm, Voltage= 3 x 230/400 V-50 Hz, 3 x 265/460 V-60 Hz (± 5% according to VDE 0530), Protection type= IP55, iso class= F (155°C), Operating mode= S1, Duty cycle= S1- 100%, Total length= approx. 597 mm, Hollow shaft = 28 mm, motor speed = 4 poles, translation with adjustment unit (i) = 70 - 350 Transmission only worm gear (i) = 50, torque = 129 Nm - 216 Nm, service factor ( f.s.)= 1, terminal box= above (rotatable), weight= 38 kg, color= RAL 5010 (gentian blue), temperature sensor= 3 x PTC thermistors, gear housing = aluminum, ball bearing = SKF, C&U or equivalent, Cooling= axial fan (plastic). For technical reasons, the variable speed worm gear motor should cannot be operated with a frequency converter. The drive corresponds to IEC 60034-30:2008, is suitable for both directions of rotation and is supplied with an oil filling. Open hollow shafts are to be sealed with a cover cap. This can be ordered under the heading "Accessories". In accordance with VDE 0105 and IEC 364, all work on the electric drive may only be carried out by qualified personnel. As usual with variable speed gears, speed control by turning the handwheel is only permitted during operation! A change in speed while stationary can damage the stepless adjustment unit. All product photos are non-binding examples! Technical changes reserved.

Worm variable speed gear motor, Power= 0.55 kW, Speed= 2.5 - 12.5 rpm, Voltage= 3 x 230/400 V-50 Hz, 3 x 265/460 V-60 Hz (± 5% according to VDE 0530), Protection class= IP55,  insulation class= F (155°C), Operating mode= S1, Duty cycle= S1- 100%, Total length= approx. 597 mm, Hollow shaft = 28 mm, motor speed = 4 poles, translation with adjustment unit (i) = 112 - 560 Transmission only worm gear (i) = 80, torque = 176 Nm - 250 Nm, service factor ( f.s.)= 1, terminal box= above (rotatable), weight= 40 kg, color= RAL 5010 (gentian blue), temperature sensor= 3 x PTC thermistors, gear housing = aluminum, ball bearing = SKF, C&U or equivalent, Cooling= axial fan (plastic). For technical reasons, the variable speed worm gear motor should cannot be operated with a frequency converter. The drive corresponds  to IEC 60034-30:2008, is suitable for both directions of rotation and is supplied with an oil filling. Open hollow shafts are to be sealed with a cover cap. This can be ordered under the heading "Accessories". According to VDE 0105 or IEC 364, all work on the electric drive may only be carried out by qualified specialists. As usual with variable speed gears, speed control by turning the handwheel is only permitted during operation! A change in speed while stationary can damage the stepless adjustment unit. All product photos are non-binding examples! Technical changes reserved.

Worm variable speed gear motor, Power= 0.55 kW, Speed= 3.5 - 16.5 rpm, Voltage= 3 x 230/400 V-50 Hz, 3 x 265/460 V-60 Hz (± 5% according to VDE 0530), Protection type= IP55, iso class= F (155°C), Operating mode= S1, Duty cycle= S1- 100%, Total length= approx. 597 mm, Hollow shaft = 28 mm, motor speed = 4 poles, translation with adjustment unit (i) = 84 - 420 Transmission only worm gear (i) = 60, torque = 146 Nm - 242 Nm, service factor ( f.s.)= 1, terminal box= above (rotatable), weight= 38 kg, color= RAL 5010 (gentian blue), temperature sensor= 3 x PTC thermistors, gear housing = aluminum, ball bearing = SKF, C&U or equivalent, Cooling= axial fan (plastic). For technical reasons, the variable speed worm gear motor should cannot be operated with a frequency converter. The drive corresponds to IEC 60034-30:2008, is suitable for both directions of rotation and is supplied with an oil filling. Open hollow shafts are to be sealed with a cover cap. This can be ordered under the heading "Accessories". In accordance with VDE 0105 and IEC 364, all work on the electric drive may only be carried out by qualified personnel. As usual with variable speed gears, speed control by turning the handwheel is only permitted during operation! A change in speed while stationary can damage the stepless adjustment unit. All product photos are non-binding examples! Technical changes reserved.

Worm variable speed gear motor, Power= 0.75 kW, Speed= 3.5 - 17 rpm, Voltage= 3 x 230/400 V-50 Hz, 3 x 265/460 V-60 Hz (± 5% according to VDE 0530), Protection type= IP55, iso class= F (155°C), Operating mode= S1, Duty cycle= S1- 100%, Total length= approx. 597 mm, Hollow shaft = 28 mm, motor speed = 4 poles, translation with adjustment unit (i) = 84 - 420 Transmission only worm gear (i) = 60, torque = 209 Nm - 300 Nm, service factor ( f.s.)= 1, terminal box= above (rotatable), weight= 40 kg, color= RAL 5010 (gentian blue), temperature sensor= 3 x PTC thermistors, gear housing = aluminum, ball bearing = SKF, C&U or equivalent, Cooling= axial fan (plastic). For technical reasons, the variable speed worm gear motor should cannot be operated with a frequency converter. The drive corresponds to IEC 60034-30:2008, is suitable for both directions of rotation and is supplied with an oil filling. Open hollow shafts are to be sealed with a cover cap. This can be ordered under the heading "Accessories". In accordance with VDE 0105 and IEC 364, all work on the electric drive may only be carried out by qualified personnel. As usual with variable speed gears, speed control by turning the handwheel is only permitted during operation! A change in speed while stationary can damage the stepless adjustment unit. All product photos are non-binding examples! Technical changes reserved.

Worm variable speed gear motor, Power= 0.75 kW, Speed= 4 – 20 rpm, Voltage= 3 x 230/400 V-50 Hz, 3 x 265/460 V-60 Hz (± 5% according to VDE 0530), Protection type= IP55, iso class= F (155°C), Operating mode= S1, Duty cycle= S1- 100%, Total length= approx. 597 mm, Hollow shaft = 28 mm, motor speed = 4 poles, translation with adjustment unit (i) = 70 - 350 Transmission only worm gear (i) = 50, torque = 292 Nm - 320 Nm, service factor ( f.s.)= 1, terminal box= above (rotatable), weight= 40 kg, color= RAL 5010 (gentian blue), temperature sensor= 3 x PTC thermistors, gear housing = aluminum, ball bearing = SKF, C&U or equivalent, Cooling= axial fan (plastic). For technical reasons, the variable speed worm gear motor should cannot be operated with a frequency converter. The drive corresponds to IEC 60034-30:2008, is suitable for both directions of rotation and is supplied with an oil filling. Open hollow shafts are to be sealed with a cover cap. This can be ordered under the heading "Accessories". In accordance with VDE 0105 and IEC 364, all work on the electric drive may only be carried out by qualified personnel. As usual with variable speed gears, speed control by turning the handwheel is only permitted during operation! A change in speed while stationary can damage the stepless adjustment unit. All product photos are non-binding examples! Technical changes reserved.

Worm variable speed gear motor, Power= 0.55 kW, Speed= 2 – 10 rpm, Voltage= 3 x 230/400 V-50 Hz, 3 x 265/460 V-60 Hz (± 5% according to VDE 0530), Protection type= IP55, iso class= F (155°C), Operating mode= S1, Duty cycle= S1- 100%, Total length= approx. 631 mm, Hollow shaft = 35 mm, motor speed = 4 poles, translation with adjustment unit (i) = 140 - 700 Transmission only worm gear (i) = 100, torque = 218 Nm - 350 Nm, service factor ( f.s.)= 1, terminal box= above (rotatable), weight= 31 kg, color= RAL 5010 (gentian blue), temperature sensor= 3 x PTC thermistor, gear housing = aluminum, ball bearing = SKF, C&U or equivalent, Cooling= axial fan (plastic). For technical reasons, the variable speed worm gear motor should cannot be operated with a frequency converter. The drive corresponds to IEC 60034-30:2008, is suitable for both directions of rotation and is supplied with an oil filling. Open hollow shafts are to be sealed with a cover cap. This can be ordered under the heading "Accessories". According to VDE 0105 and IEC 364, all work on the electric drive may only be carried out by qualified personnel. As usual with variable speed gears, speed control by turning the handwheel is only permitted during operation! A change in speed while stationary can damage the stepless adjustment unit. All product photos are non-binding examples! Technical changes reserved.

Worm variable speed gear motor, Power= 0.55 kW, Speed= 2.5 - 12.5 rpm, Voltage= 3 x 230/400 V-50 Hz, 3 x 265/460 V-60 Hz (± 5% according to VDE 0530), Protection type= IP55, iso class= F (155°C), Operating mode= S1, Duty cycle= S1- 100%, Total length= approx. 631 mm, Hollow shaft = 35 mm, motor speed = 4 poles, translation with adjustment unit (i) = 112 - 560 Transmission only worm gear (i) = 80, torque = 189 Nm - 309 Nm, operating factor ( f.s.)= 1, terminal box= above (rotatable), weight= 31 kg, color= RAL 5010 (gentian blue), temperature sensor= 3 x PTC thermistor, gear housing = aluminum, ball bearing = SKF, C&U or equivalent, Cooling= axial fan (plastic). For technical reasons, the variable speed worm gear motor should cannot be operated with a frequency converter. The drive corresponds to IEC 60034-30:2008, is suitable for both directions of rotation and is supplied with an oil filling. Open hollow shafts are to be sealed with a cover cap. This can be ordered under the heading "Accessories". According to VDE 0105 and IEC 364, all work on the electric drive may only be carried out by qualified personnel. As usual with variable speed gears, speed control by turning the handwheel is only permitted during operation! A change in speed while stationary can damage the stepless adjustment unit. All product photos are non-binding examples! Technical changes reserved.

Worm variable speed gear motor, Power= 0.75 kW, Speed= 2 – 10 rpm, Voltage= 3 x 230/400 V-50 Hz, 3 x 265/460 V-60 Hz (± 5% according to VDE 0530), Protection type= IP55, iso class= F (155°C), Operating mode= S1, Duty cycle= S1- 100%, Total length= approx. 631 mm, Hollow shaft = 35 mm, motor speed = 4 poles, translation with adjustment unit (i) = 140 - 700 Transmission only worm gear (i) = 100, torque = 303 Nm - 410 Nm, service factor ( f.s.)= 1, terminal box= above (rotatable), weight= 31 kg, color= RAL 5010 (gentian blue), temperature sensor= 3 x PTC thermistor, gear housing = aluminum, ball bearing = SKF, C&U or equivalent, Cooling= axial fan (plastic). For technical reasons, the variable speed worm gear motor should cannot be operated with a frequency converter. The drive corresponds to IEC 60034-30:2008, is suitable for both directions of rotation and is supplied with an oil filling. Open hollow shafts are to be sealed with a cover cap. This can be ordered under the heading "Accessories". According to VDE 0105 and IEC 364, all work on the electric drive may only be carried out by qualified personnel. As usual with variable speed gears, speed control by turning the handwheel is only permitted during operation! A change in speed while stationary can damage the stepless adjustment unit. All product photos are non-binding examples! Technical changes reserved.

Worm variable speed gear motor, Power= 0.75 kW, Speed= 2.5 - 12.5 rpm, Voltage= 3 x 230/400 V-50 Hz, 3 x 265/460 V-60 Hz (± 5% according to VDE 0530), Protection type= IP55, iso class= F (155°C), Operating mode= S1, Duty cycle= S1- 100%, Total length= approx. 631 mm, Hollow shaft = 35 mm, motor speed = 4 poles, translation with adjustment unit (i) = 112 - 560 Transmission only worm gear (i) = 80, torque = 265 Nm - 428 Nm, operating factor ( f.s.)= 1, terminal box= above (rotatable), weight= 31 kg, color= RAL 5010 (gentian blue), temperature sensor= 3 x PTC thermistors, gear housing = aluminum, ball bearing = SKF, C&U or equivalent, Cooling= axial fan (plastic). For technical reasons, the variable speed worm gear motor should cannot be operated with a frequency converter. The drive corresponds to IEC 60034-30:2008, is suitable for both directions of rotation and is supplied with an oil filling. Open hollow shafts are to be sealed with a cover cap. This can be ordered under the heading "Accessories". According to VDE 0105 and IEC 364, all work on the electric drive may only be carried out by qualified personnel. As usual with variable speed gears, speed control by turning the hand wheel is only permitted during operation! A change in speed while stationary can damage the stepless adjustment unit. All product photos are non-binding examples! Technical changes reserved.

Worm variable speed gear motor, Power= 0.75 kW, Speed= 3.5 - 16.5 rpm, Voltage= 3 x 230/400 V-50 Hz, 3 x 265/460 V-60 Hz (± 5% according to VDE 0530), Protection type= IP55, iso class= F (155°C), Operating mode= S1, Duty cycle= S1- 100%, Total length= approx. 631 mm, Hollow shaft = 35 mm, motor speed = 4 poles, translation with adjustment unit (i) = 84 - 420 Transmission only worm gear (i) = 60, torque = 230 Nm - 389 Nm, service factor ( f.s.)= 1, terminal box= above (rotatable), weight= 31 kg, color= RAL 5010 (gentian blue), temperature sensor= 3 x PTC thermistors, gear housing = aluminum, ball bearing = SKF, C&U or equivalent, Cooling= axial fan (plastic). For technical reasons, the variable speed worm gear motor should cannot be operated with a frequency converter. The drive corresponds to IEC 60034-30:2008, is suitable for both directions of rotation and is supplied with an oil filling. Open hollow shafts are to be sealed with a cover cap. This can be ordered under the heading "Accessories". According to VDE 0105 and IEC 364, all work on the electric drive may only be carried out by qualified personnel. As usual with variable speed gears, speed control by turning the hand wheel is only permitted during operation! A change in speed while stationary can damage the stepless adjustment unit. All product photos are non-binding examples! Technical changes reserved.

Worm variable speed gear motor, Power= 1.1 kW, Speed= 20 - 100 rpm, Voltage= 3 x 230/400 V-50 Hz, 3 x 265/460 V-60 Hz (± 5% according to VDE 0530), Protection type= IP55, iso class= F (155°C), Operating mode= S1, Duty cycle= S1- 100%, Total length= approx. 643 mm, Hollow shaft= 28 mm, motor Speed= 4 poles, gear ratio with adjustment unit (i)= 14 - 70 Gear ratio only worm gear (i)= 10, torque= 77 Nm - 144 Nm, service factor ( f.s.)= 1, terminal box= above (rotatable), weight= 52 kg, color= RAL 5010 (gentian blue), temperature sensor= 3 x PTC thermistors, gear housing = aluminum, ball bearing = SKF, C&U or equivalent, Cooling= axial fan (plastic). For technical reasons, the variable speed worm gear motor should cannot be operated with a frequency converter. The drive corresponds to IEC 60034-30:2008, is suitable for both directions of rotation and is supplied with an oil filling. Open hollow shafts are to be sealed with a cover cap. This can be ordered under the heading "Accessories". In accordance with VDE 0105 and IEC 364, all work on the electric drive may only be carried out by qualified personnel. As usual with variable speed gears, speed control by turning the hand wheel is only permitted during operation! A change in speed while stationary can damage the stepless adjustment unit. All product photos are non-binding examples! Technical changes reserved.

Worm variable speed gear motor, Power= 1.1 kW, Speed= 10 - 50 rpm, Voltage= 3 x 230/400 V-50 Hz, 3 x 265/460 V-60 Hz (± 5% according to VDE 0530), Protection type= IP55, iso class= F (155°C), Operating mode= S1, Duty cycle= S1- 100%, Total length= approx. 643 mm, Hollow shaft = 28 mm, motor speed = 4 poles, translation with adjustment unit (i) = 28 - 1405 Transmission only worm gear (i) = 20, torque = 142 Nm - 258 Nm, service factor ( f.s.)= 1, terminal box= above (rotatable), weight= 52 kg, color= RAL 5010 (gentian blue), temperature sensor= 3 x PTC thermistor, gear housing = aluminum, ball bearing = SKF, C&U or equivalent, Cooling= axial fan (plastic). For technical reasons, the variable speed worm gear motor should cannot be operated with a frequency converter. The drive corresponds to IEC 60034-30:2008, is suitable for both directions of rotation and is supplied with an oil filling. Open hollow shafts are to be sealed with a cover cap. This can be ordered under the heading "Accessories". In accordance with VDE 0105 and IEC 364, all work on the electric drive may only be carried out by qualified personnel. As usual with variable speed gears, speed control by turning the handwheel is only permitted during operation! A change in speed while stationary can damage the stepless adjustment unit. All product photos are non-binding examples! Technical changes reserved.

Worm variable speed gear motor, Power= 1.1 kW, Speed= 8 - 40 rpm, Voltage= 3 x 230/400 V-50 Hz, 3 x 265/460 V-60 Hz (± 5% according to VDE 0530), Protection type= IP55, iso class= F (155°C), Operating mode= S1, Duty cycle= S1- 100%, Total length= approx. 643 mm, Hollow shaft = 28 mm, motor speed = 4 poles, translation with adjustment unit (i) = 35 - 175 Transmission only worm gear (i) = 25, torque = 172 Nm - 308 Nm, service factor ( f.s.)= 1, terminal box= above (rotatable), weight= 52 kg, color= RAL 5010 (gentian blue), temperature sensor= 3 x PTC thermistor, gear housing = aluminum, ball bearing = SKF, C&U or equivalent, Cooling= axial fan (plastic). For technical reasons, the variable speed worm gear motor should cannot be operated with a frequency converter. The drive corresponds to IEC 60034-30:2008, is suitable for both directions of rotation and is supplied with an oil filling. Open hollow shafts are to be sealed with a cover cap. This can be ordered under the heading "Accessories". In accordance with VDE 0105 and IEC 364, all work on the electric drive may only be carried out by qualified personnel. As usual with variable speed gears, speed control by turning the handwheel is only permitted during operation! A change in speed while stationary can damage the stepless adjustment unit. All product photos are non-binding examples! Technical changes reserved.

Worm variable speed gear motor, Power= 1.1 kW, Speed= 13.5 - 66.5 rpm, Voltage= 3 x 230/400 V-50 Hz, 3 x 265/460 V-60 Hz (± 5% according to VDE 0530), Protection type= IP55, iso class= F (155°C), Operating mode= S1, Duty cycle= S1- 100%, Total length= approx. 643 mm, Hollow shaft = 28 mm, motor speed = 4 poles, translation with adjustment unit (i) = 21 - 105 Transmission only worm gear (i) = 15, torque = 110 Nm - 203 Nm, service factor ( f.s.)= 1, terminal box= above (rotatable), weight= 52 kg, color= RAL 5010 (gentian blue), temperature sensor= 3 x PTC thermistor, gear housing = aluminum, ball bearing = SKF, C&U or equivalent, Cooling= axial fan (plastic). For technical reasons, the variable speed worm gear motor should cannot be operated with a frequency converter. The drive corresponds to IEC 60034-30:2008, is suitable for both directions of rotation and is supplied with an oil filling. Open hollow shafts are to be sealed with a cover cap. This can be ordered under the heading "Accessories". In accordance with VDE 0105 and IEC 364, all work on the electric drive may only be carried out by qualified personnel. As usual with variable speed gears, speed control by turning the handwheel is only permitted during operation! A change in speed while stationary can damage the stepless adjustment unit. All product photos are non-binding examples! Technical changes reserved.

Worm variable speed gear motor, Power= 1.1 kW, Speed= 7 - 33 rpm, Voltage= 3 x 230/400 V-50 Hz, 3 x 265/460 V-60 Hz (± 5% according to VDE 0530), Protection type= IP55, iso class= F (155°C), Operating mode= S1, Duty cycle= S1- 100%, Total length= approx. 643 mm, Hollow shaft = 28 mm, motor speed = 4 poles, translation with adjustment unit (i) = 42 - 210 Transmission only worm gear (i) = 30, torque = 195 Nm - 340 Nm, service factor ( f.s.)= 1, terminal box= above (rotatable), weight= 52 kg, color= RAL 5010 (gentian blue), temperature sensor= 3 x PTC thermistors, gear housing = aluminum, ball bearing = SKF, C&U or equivalent, Cooling= axial fan (plastic). For technical reasons, the variable speed worm gear motor should cannot be operated with a frequency converter. The drive corresponds to IEC 60034-30:2008, is suitable for both directions of rotation and is supplied with an oil filling. Open hollow shafts are to be sealed with a cover cap. This can be ordered under the heading "Accessories". In accordance with VDE 0105 and IEC 364, all work on the electric drive may only be carried out by qualified personnel. As usual with variable speed gears, speed control by turning the hand wheel is only permitted during operation! A change in speed while stationary can damage the stepless adjustment unit. All product photos are non-binding examples! Technical changes reserved.

Worm variable speed gear motor, Power= 1.1 kW, Speed= 27 - 133 rpm, Voltage= 3 x 230/400 V-50 Hz, 3 x 265/460 V-60 Hz (± 5% according to VDE 0530), Protection type= IP55, iso class= F (155°C), Operating mode= S1, Duty cycle= S1- 100%, Total length= approx. 643 mm, Hollow shaft = 28 mm, motor speed = 4 poles, translation with adjustment unit (i) = 10.5 - 52.5 Transmission only worm gear (i) = 7.5, torque = 55 Nm – 111 Nm, service factor (f.s.)= 1, terminal box= above (rotatable), weight= 52 kg, color= RAL 5010 (gentian blue), temperature sensor= 3 x PTC thermistors, gearbox housing = aluminium, ball bearings = SKF, C&U or equivalent, Cooling= axial fan (plastic). For technical reasons, the variable speed worm gear motor should cannot be operated with a frequency converter. The drive corresponds to IEC 60034-30:2008, is suitable for both directions of rotation and is supplied with an oil filling. Open hollow shafts are to be sealed with a cover cap. This can be ordered under the heading "Accessories". In accordance with VDE 0105 and IEC 364, all work on the electric drive may only be carried out by qualified personnel. As usual with variable speed gears, speed control by turning the handwheel is only permitted during operation! A change in speed while stationary can damage the stepless adjustment unit. All product photos are non-binding examples! Technical changes reserved.

Worm variable speed gear motor, Power= 1.1 kW, Speed= 5 - 25 rpm, Voltage= 3 x 230/400 V-50 Hz, 3 x 265/460 V-60 Hz (± 5% according to VDE 0530), Protection type= IP55, iso class= F (155°C), Operating mode= S1, Duty cycle= S1- 100%, Total length= approx. 643 mm, Hollow shaft = 28 mm, motor speed = 4 poles, translation with adjustment unit (i) = 56 - 280 Transmission only worm gear (i) = 40, torque = 245 Nm - 360 Nm, service factor ( f.s.)= 1, terminal box= above (rotatable), weight= 52 kg, color= RAL 5010 (gentian blue), temperature sensor= 3 x PTC thermistors, gear housing = aluminum, ball bearing = SKF, C&U or equivalent, Cooling= axial fan (plastic). For technical reasons, the variable speed worm gear motor should cannot be operated with a frequency converter. The drive corresponds to IEC 60034-30:2008, is suitable for both directions of rotation and is supplied with an oil filling. Open hollow shafts are to be sealed with a cover cap. This can be ordered under the heading "Accessories". In accordance with VDE 0105 and IEC 364, all work on the electric drive may only be carried out by qualified personnel. As usual with variable speed gears, speed control by turning the hand wheel is only permitted during operation! A change in speed while stationary can damage the stepless adjustment unit. All product photos are non-binding examples! Technical changes reserved.

Worm variable speed gear motor, Power= 1.5 kW, Speed= 10 - 50 rpm, Voltage= 3 x 230/400 V-50 Hz, 3 x 265/460 V-60 Hz (± 5% according to VDE 0530), Protection type= IP55, iso class= F (155°C), Operating mode= S1, Duty cycle= S1- 100%, Total length= approx. 668 mm, Hollow shaft = 28 mm, motor speed = 4 poles, translation with adjustment unit (i) = 28 - 140 Transmission only worm gear (i) = 20, torque = 190 Nm - 344 Nm, operating factor ( f.s.)= 1, terminal box= above (rotatable), weight= 54 kg, color= RAL 5010 (gentian blue), temperature sensor= 3 x PTC thermistor, gear housing = aluminum, ball bearing = SKF, C&U or equivalent, Cooling= axial fan (plastic). For technical reasons, the variable speed worm gear motor should cannot be operated with a frequency converter. The drive corresponds to IEC 60034-30:2008, is suitable for both directions of rotation and is supplied with an oil filling. Open hollow shafts are to be sealed with a cover cap. This can be ordered under the heading "Accessories". In accordance with VDE 0105 and IEC 364, all work on the electric drive may only be carried out by qualified personnel. As usual with variable speed gears, speed control by turning the handwheel is only permitted during operation! A change in speed while stationary can damage the stepless adjustment unit. All product photos are non-binding examples! Technical changes reserved.