Worm variable speed gear motor, Power= 1.5 kW, Speed= 20 - 100 rpm, Voltage= 3 x 230/400 V-50 Hz, 3 x 265/460 V-60 Hz (± 5% according to VDE 0530), Protection type= IP55, iso class= F (155°C), Operating mode= S1, Duty cycle= S1- 100%, Total length= approx. 668 mm, Hollow shaft = 28 mm, motor speed = 4 poles, translation with adjustment unit (i) = 14 - 70 Transmission only worm gear (i) = 10, torque = 102 Nm - 192 Nm, service factor ( f.s.)= 1, terminal box= above (rotatable), weight= 56 kg, color= RAL 5010 (gentian blue), temperature sensor= 3 x PTC thermistors, gear housing = aluminum, ball bearing = SKF, C&U or equivalent, Cooling= axial fan (plastic). For technical reasons, the variable speed worm gear motor should cannot be operated with a frequency converter. The drive corresponds to IEC 60034-30:2008, is suitable for both directions of rotation and is supplied with an oil filling. Open hollow shafts are to be sealed with a cover cap. This can be ordered under the heading "Accessories". In accordance with VDE 0105 and IEC 364, all work on the electric drive may only be carried out by qualified personnel. As usual with variable speed gears, speed control by turning the handwheel is only permitted during operation! A change in speed while stationary can damage the stepless adjustment unit. All product photos are non-binding examples! Technical changes reserved.

Worm variable speed gear motor, Power= 1.5 kW, Speed= 7 - 33 rpm, Voltage= 3 x 230/400 V-50 Hz, 3 x 265/460 V-60 Hz (± 5% according to VDE 0530), Protection type= IP55, iso class= F (155°C), Operating mode= S1, Duty cycle= S1- 100%, Total length= approx. 668 mm, Hollow shaft = 28 mm, motor speed = 4 poles, translation with adjustment unit (i) = 42 - 210 Transmission only worm gear (i) = 30, torque = 260 Nm - 390 Nm, operating factor ( f.s.)= 1, terminal box= above (rotatable), weight= 54 kg, color= RAL 5010 (gentian blue), temperature sensor= 3 x PTC thermistor, gear housing = aluminum, ball bearing = SKF, C&U or equivalent, Cooling= axial fan (plastic). For technical reasons, the variable speed worm gear motor should cannot be operated with a frequency converter. The drive corresponds to IEC 60034-30:2008, is suitable for both directions of rotation and is supplied with an oil filling. Open hollow shafts are to be sealed with a cover cap. This can be ordered under the heading "Accessories". In accordance with VDE 0105 and IEC 364, all work on the electric drive may only be carried out by qualified personnel. As usual with variable speed gears, speed control by turning the handwheel is only permitted during operation! A change in speed while stationary can damage the stepless adjustment unit. All product photos are non-binding examples! Technical changes reserved.

Worm variable speed gear motor, Power= 1.5 kW, Speed= 8 - 40 rpm, Voltage= 3 x 230/400 V-50 Hz, 3 x 265/460 V-60 Hz (± 5% according to VDE 0530), Protection type= IP55, iso class= F (155°C), Operating mode= S1, Duty cycle= S1- 100%, Total length= approx. 668 mm, Hollow shaft = 28 mm, motor speed = 4 poles, translation with adjustment unit (i) = 35 - 175 Transmission only worm gear (i) = 25, torque = 229 Nm - 330 Nm, service factor ( f.s.)= 1, terminal box= above (rotatable), weight= 54 kg, color= RAL 5010 (gentian blue), temperature sensor= 3 x PTC thermistor, gear housing = aluminum, ball bearing = SKF, C&U or equivalent, Cooling= axial fan (plastic). For technical reasons, the variable speed worm gear motor should cannot be operated with a frequency converter. The drive corresponds to IEC 60034-30:2008, is suitable for both directions of rotation and is supplied with an oil filling. Open hollow shafts are to be sealed with a cover cap. This can be ordered under the heading "Accessories". In accordance with VDE 0105 and IEC 364, all work on the electric drive may only be carried out by qualified personnel. As usual with variable speed gears, speed control by turning the handwheel is only permitted during operation! A change in speed while stationary can damage the stepless adjustment unit. All product photos are non-binding examples! Technical changes reserved.

Worm variable speed gear motor, Power= 1.5 kW, Speed= 5 - 25 rpm, Voltage= 3 x 230/400 V-50 Hz, 3 x 265/460 V-60 Hz (± 5% according to VDE 0530), Protection type= IP55, iso class= F (155°C), Operating mode= S1, Duty cycle= S1- 100%, Total length= approx. 668 mm, Hollow shaft = 28 mm, motor speed = 4 poles, translation with adjustment unit (i) = 56 - 280 Transmission only worm gear (i) = 40, torque = 327 Nm - 360 Nm, service factor ( f.s.)= 1, terminal box= above (rotatable), weight= 54 kg, color= RAL 5010 (gentian blue), temperature sensor= 3 x PTC thermistor, gear housing = aluminum, ball bearing = SKF, C&U or equivalent, Cooling= axial fan (plastic). For technical reasons, the variable speed worm gear motor should cannot be operated with a frequency converter. The drive corresponds to IEC 60034-30:2008, is suitable for both directions of rotation and is supplied with an oil filling. Open hollow shafts are to be sealed with a cover cap. This can be ordered under the heading "Accessories". In accordance with VDE 0105 and IEC 364, all work on the electric drive may only be carried out by qualified personnel. As usual with variable speed gears, speed control by turning the handwheel is only permitted during operation! A change in speed while stationary can damage the stepless adjustment unit. All product photos are non-binding examples! Technical changes reserved.

Worm variable speed gear motor, Power= 1.5 kW, Speed= 13.5 - 66.5 rpm, Voltage= 3 x 230/400 V-50 Hz, 3 x 265/460 V-60 Hz (± 5% according to VDE 0530), Protection type= IP55, iso class= F (155°C), Operating mode= S1, Duty cycle= S1- 100%, Total length= approx. 668 mm, Hollow shaft= 28 mm, motor Speed= 4 poles, gear ratio with adjustment unit (i)= 21 - 105 Gear ratio only worm gear (i)= 15, torque= 147 Nm - 270 Nm, operating factor ( f.s.)= 1, terminal box= above (rotatable), weight= 54 kg, color= RAL 5010 (gentian blue), temperature sensor= 3 x PTC thermistor, gear housing = aluminum, ball bearing = SKF, C&U or equivalent, Cooling= axial fan (plastic). For technical reasons, the variable speed worm gear motor should cannot be operated with a frequency converter. The drive corresponds to IEC 60034-30:2008, is suitable for both directions of rotation and is supplied with an oil filling. Open hollow shafts are to be sealed with a cover cap. This can be ordered under the heading "Accessories". In accordance with VDE 0105 and IEC 364, all work on the electric drive may only be carried out by qualified personnel. As usual with variable speed gears, speed control by turning the handwheel is only permitted during operation! A change in speed while stationary can damage the stepless adjustment unit. All product photos are non-binding examples! Technical changes reserved.

Worm variable speed gear motor, Power= 1.5 kW, Speed= 27 - 133 rpm, Voltage= 3 x 230/400 V-50 Hz, 3 x 265/460 V-60 Hz (± 5% according to VDE 0530), Protection type= IP55, iso class= F (155°C), Operating mode= S1, Duty cycle= S1- 100%, Total length= approx. 668 mm, Hollow shaft = 28 mm, motor speed = 4 poles, translation with adjustment unit (i) = 10.5 - 52.5 Transmission only worm gear (i) = 7.5, torque = 78 Nm – 148 Nm, service factor (f.s.)= 1, terminal box= above (rotatable), weight= 54 kg, color= RAL 5010 (gentian blue), temperature sensor= 3 x PTC thermistors, gearbox housing = aluminium, ball bearings = SKF, C&U or equivalent, Cooling= axial fan (plastic). For technical reasons, the variable speed worm gear motor should cannot be operated with a frequency converter. The drive corresponds to IEC 60034-30:2008, is suitable for both directions of rotation and is supplied with an oil filling. Open hollow shafts are to be sealed with a cover cap. This can be ordered under the heading "Accessories". In accordance with VDE 0105 and IEC 364, all work on the electric drive may only be carried out by qualified personnel. As usual with variable speed gears, speed control by turning the handwheel is only permitted during operation! A change in speed while stationary can damage the stepless adjustment unit. All product photos are non-binding examples! Technical changes reserved.

Worm variable speed gear motor, Power= 0.75 kW, Speed= 2.5 - 12.5 rpm, Voltage= 3 x 230/400 V-50 Hz, 3 x 265/460 V-60 Hz (± 5% according to VDE 0530), Protection type= IP55, iso class= F (155°C), Operating mode= S1, Duty cycle= S1- 100%, Total length= approx. 686 mm, Hollow shaft = 42 mm, motor speed = 4 poles, translation with adjustment unit (i) = 112 - 560 Transmission only worm gear (i) = 80, torque = 302 Nm - 503 Nm, service factor ( f.s.)= 1, terminal box= above (rotatable), weight= 19 kg, color= RAL 5010 (gentian blue), temperature sensor= 3 x PTC thermistors, gear housing = aluminum, ball bearing = SKF, C&U or equivalent, Cooling= axial fan (plastic). For technical reasons, the variable speed worm gear motor should cannot be operated with a frequency converter. The drive corresponds to IEC 60034-30:2008, is suitable for both directions of rotation and is supplied with an oil filling. Open hollow shafts are to be sealed with a cover cap. This can be ordered under the heading "Accessories". According to VDE 0105 and IEC 364, all work on the electric drive may only be carried out by qualified personnel. As usual with variable speed gears, speed control by turning the handwheel is only permitted during operation! A change in speed while stationary can damage the stepless adjustment unit. All product photos are non-binding examples! Technical changes reserved.

Worm variable speed gear motor, Power= 0.75 kW, Speed= 2 – 10 rpm, Voltage= 3 x 230/400 V-50 Hz, 3 x 265/460 V-60 Hz (± 5% according to VDE 0530), Protection type= IP55, iso class= F (155°C), Operating mode= S1, Duty cycle= S1- 100%, Total length= approx. 686 mm, Hollow shaft = 42 mm, motor speed = 4 poles, translation with adjustment unit (i) = 140 - 700 Transmission only worm gear (i) = 100, torque = 348 Nm - 575 Nm, service factor ( f.s.)= 1, terminal box= above (rotatable), weight= 19 kg, color= RAL 5010 (gentian blue), temperature sensor= 3 x PTC thermistors, gear housing = aluminum, ball bearing = SKF, C&U or equivalent, Cooling= axial fan (plastic). For technical reasons, the variable speed worm gear motor should cannot be operated with a frequency converter. The drive corresponds to IEC 60034-30:2008, is suitable for both directions of rotation and is supplied with an oil filling. Open hollow shafts are to be sealed with a cover cap. This can be ordered under the heading "Accessories". According to VDE 0105 and IEC 364, all work on the electric drive may only be carried out by qualified personnel. As usual with variable speed gears, speed control by turning the hand wheel is only permitted during operation! A change in speed while stationary can damage the stepless adjustment unit. All product photos are non-binding examples! Technical changes reserved.

Worm variable speed gear motor, Power= 1.1 kW, Speed= 13.5 - 66.5 rpm, Voltage= 3 x 230/400 V-50 Hz, 3 x 265/460 V-60 Hz (± 5% according to VDE 0530), Protection type= IP55, iso class= F (155°C), Operating mode= S1, Duty cycle= S1- 100%, Total length= approx. 677 mm, Hollow shaft = 35 mm, motor speed = 4 poles, translation with adjustment unit (i) = 21 - 105 Transmission only worm gear (i) = 15, torque = 113 Nm - 208 Nm, operating factor ( f.s.)= 1, terminal box= above (rotatable), weight= 58 kg, color= RAL 5010 (gentian blue), temperature sensor= 3 x PTC thermistor, gear housing = aluminum, ball bearing = SKF, C&U or equivalent, Cooling= axial fan (plastic). For technical reasons, the variable speed worm gear motor should cannot be operated with a frequency converter. The drive corresponds to IEC 60034-30:2008, is suitable for both directions of rotation and is supplied with an oil filling. Open hollow shafts are to be sealed with a cover cap. This can be ordered under the heading "Accessories". In accordance with VDE 0105 and IEC 364, all work on the electric drive may only be carried out by qualified personnel. As usual with variable speed gears, speed control by turning the handwheel is only permitted during operation! A change in speed while stationary can damage the stepless adjustment unit. All product photos are non-binding examples! Technical changes reserved.

Worm variable speed gear motor, Power= 1.1 kW, Speed= 5 - 25 rpm, Voltage= 3 x 230/400 V-50 Hz, 3 x 265/460 V-60 Hz (± 5% according to VDE 0530), Protection type= IP55, iso class= F (155°C), Operating mode= S1, Duty cycle= S1- 100%, Total length= approx. 677 mm, Hollow shaft = 35 mm, motor speed = 4 poles, translation with adjustment unit (i) = 56 - 280 Transmission only worm gear (i) = 40, torque = 256 Nm - 442 Nm, service factor ( f.s.)= 1, terminal box= above (rotatable), weight= 58 kg, color= RAL 5010 (gentian blue), temperature sensor= 3 x PTC thermistor, gear housing = aluminum, ball bearing = SKF, C&U or equivalent, Cooling= axial fan (plastic). For technical reasons, the variable speed worm gear motor should cannot be operated with a frequency converter. The drive corresponds to IEC 60034-30:2008, is suitable for both directions of rotation and is supplied with an oil filling. Open hollow shafts are to be sealed with a cover cap. This can be ordered under the heading "Accessories". In accordance with VDE 0105 and IEC 364, all work on the electric drive may only be carried out by qualified personnel. As usual with variable speed gears, speed control by turning the hand wheel is only permitted during operation! A change in speed while stationary can damage the stepless adjustment unit. All product photos are non-binding examples! Technical changes reserved.

Worm variable speed gear motor, Power= 1.1 kW, Speed= 20 - 100 rpm, Voltage= 3 x 230/400 V-50 Hz, 3 x 265/460 V-60 Hz (± 5% according to VDE 0530), Protection type= IP55, iso class= F (155°C), Operating mode= S1, Duty cycle= S1- 100%, Total length= approx. 677 mm, Hollow shaft= 35 mm, motor Speed= 4 poles, gear ratio with adjustment unit (i)= 14 - 70 Gear ratio only worm gear (i)= 10, torque= 78 Nm - 146 Nm, service factor ( f.s.)= 1, terminal box= above (rotatable), weight= 58 kg, color= RAL 5010 (gentian blue), temperature sensor= 3 x PTC thermistor, gear housing = aluminum, ball bearing = SKF, C&U or equivalent, Cooling= axial fan (plastic). For technical reasons, the variable speed worm gear motor should cannot be operated with a frequency converter. The drive corresponds to IEC 60034-30:2008, is suitable for both directions of rotation and is supplied with an oil filling. Open hollow shafts are to be sealed with a cover cap. This can be ordered under the heading "Accessories". In accordance with VDE 0105 and IEC 364, all work on the electric drive may only be carried out by qualified personnel. As usual with variable speed gears, speed control by turning the handwheel is only permitted during operation! A change in speed while stationary can damage the stepless adjustment unit. All product photos are non-binding examples! Technical changes reserved.

Worm variable speed gear motor, Power= 1.1 kW, Speed= 8 - 40 rpm, Voltage= 3 x 230/400 V-50 Hz, 3 x 265/460 V-60 Hz (± 5% according to VDE 0530), Protection type= IP55, iso class= F (155°C), Operating mode= S1, Duty cycle= S1- 100%, Total length= approx. 677 mm, Hollow shaft = 35 mm, motor speed = 4 poles, translation with adjustment unit (i) = 35 - 175 Transmission only worm gear (i) = 25, torque = 177 Nm - 320 Nm, service factor ( f.s.)= 1, terminal box= above (rotatable), weight= 58 kg, color= RAL 5010 (gentian blue), temperature sensor= 3 x PTC thermistor, gear housing = aluminum, ball bearing = SKF, C&U or equivalent, Cooling= axial fan (plastic). For technical reasons, the variable speed worm gear motor should cannot be operated with a frequency converter. The drive corresponds to IEC 60034-30:2008, is suitable for both directions of rotation and is supplied with an oil filling. Open hollow shafts are to be sealed with a cover cap. This can be ordered under the heading "Accessories". In accordance with VDE 0105 and IEC 364, all work on the electric drive may only be carried out by qualified personnel. As usual with variable speed gears, speed control by turning the handwheel is only permitted during operation! A change in speed while stationary can damage the stepless adjustment unit. All product photos are non-binding examples! Technical changes reserved.

Worm variable speed gear motor, Power= 1.1 kW, Speed= 10 - 50 rpm, Voltage= 3 x 230/400 V-50 Hz, 3 x 265/460 V-60 Hz (± 5% according to VDE 0530), Protection type= IP55, iso class= F (155°C), Operating mode= S1, Duty cycle= S1- 100%, Total length= approx. 677 mm, Hollow shaft= 35 mm, motor Speed= 4 poles, gear ratio with adjustment unit (i)= 28 - 140 Gear ratio only worm gear (i)= 20, torque= 146 Nm - 266 Nm, operating factor ( f.s.)= 1, terminal box= above (rotatable), weight= 58 kg, color= RAL 5010 (gentian blue), temperature sensor= 3 x PTC thermistor, gear housing = aluminum, ball bearing = SKF, C&U or equivalent, Cooling= axial fan (plastic). For technical reasons, the variable speed worm gear motor should cannot be operated with a frequency converter. The drive corresponds to IEC 60034-30:2008, is suitable for both directions of rotation and is supplied with an oil filling. Open hollow shafts are to be sealed with a cover cap. This can be ordered under the heading "Accessories". In accordance with VDE 0105 and IEC 364, all work on the electric drive may only be carried out by qualified personnel. As usual with variable speed gears, speed control by turning the handwheel is only permitted during operation! A change in speed while stationary can damage the stepless adjustment unit. All product photos are non-binding examples! Technical changes reserved.

Worm variable speed gear motor, Power= 1.1 kW, Speed= 7 - 33 rpm, Voltage= 3 x 230/400 V-50 Hz, 3 x 265/460 V-60 Hz (± 5% according to VDE 0530), Protection type= IP55, iso class= F (155°C), Operating mode= S1, Duty cycle= S1- 100%, Total length= approx. 677 mm, Hollow shaft = 35 mm, motor speed = 4 poles, translation with adjustment unit (i) = 42 - 210 Transmission only worm gear (i) = 30, torque = 202 Nm - 356 Nm, operating factor ( f.s.)= 1, terminal box= above (rotatable), weight= 58 kg, color= RAL 5010 (gentian blue), temperature sensor= 3 x PTC thermistor, gear housing = aluminum, ball bearing = SKF, C&U or equivalent, Cooling= axial fan (plastic). For technical reasons, the variable speed worm gear motor should cannot be operated with a frequency converter. The drive corresponds to IEC 60034-30:2008, is suitable for both directions of rotation and is supplied with an oil filling. Open hollow shafts are to be sealed with a cover cap. This can be ordered under the heading "Accessories". In accordance with VDE 0105 and IEC 364, all work on the electric drive may only be carried out by qualified personnel. As usual with variable speed gears, speed control by turning the handwheel is only permitted during operation! A change in speed while stationary can damage the stepless adjustment unit. All product photos are non-binding examples! Technical changes reserved.

Worm variable speed gear motor, Power= 1.1 kW, Speed= 4 - 20 rpm, Voltage= 3 x 230/400 V-50 Hz, 3 x 265/460 V-60 Hz (± 5% according to VDE 0530), Protection type= IP55, iso class= F (155°C), Operating mode= S1, Duty cycle= S1- 100%, Total length= approx. 677 mm, Hollow shaft = 35 mm, motor speed = 4 poles, translation with adjustment unit (i) = 70 - 350 Transmission only worm gear (i) = 50, torque = 304 Nm - 517 Nm, service factor ( f.s.)= 1, terminal box= above (rotatable), weight= 58 kg, color= RAL 5010 (gentian blue), temperature sensor= 3 x PTC thermistor, gear housing = aluminum, ball bearing = SKF, C&U or equivalent, Cooling= axial fan (plastic). For technical reasons, the variable speed worm gear motor should cannot be operated with a frequency converter. The drive corresponds to IEC 60034-30:2008, is suitable for both directions of rotation and is supplied with an oil filling. Open hollow shafts are to be sealed with a cover cap. This can be ordered under the heading "Accessories". In accordance with VDE 0105 and IEC 364, all work on the electric drive may only be carried out by qualified personnel. As usual with variable speed gears, speed control by turning the handwheel is only permitted during operation! A change in speed while stationary can damage the stepless adjustment unit. All product photos are non-binding examples! Technical changes reserved.

Worm variable speed gear motor, Power= 1.5 kW, Speed= 5 - 25 rpm, Voltage= 3 x 230/400 V-50 Hz, 3 x 265/460 V-60 Hz (± 5% according to VDE 0530), Protection type= IP55, iso class= F (155°C), Operating mode= S1, Duty cycle= S1- 100%, Total length= approx. 702 mm, Hollow shaft = 35 mm, motor speed = 4 poles, translation with adjustment unit (i) = 56 - 280 Transmission only worm gear (i) = 40, torque = 341 Nm - 589 Nm, service factor ( f.s.)= 1, terminal box= above (rotatable), weight= 58 kg, color= RAL 5010 (gentian blue), temperature sensor= 3 x PTC thermistor, gear housing = aluminum, ball bearing = SKF, C&U or equivalent, Cooling= axial fan (plastic). For technical reasons, the variable speed worm gear motor should cannot be operated with a frequency converter. The drive corresponds to IEC 60034-30:2008, is suitable for both directions of rotation and is supplied with an oil filling. Open hollow shafts are to be sealed with a cover cap. This can be ordered under the heading "Accessories". In accordance with VDE 0105 and IEC 364, all work on the electric drive may only be carried out by qualified personnel. As usual with variable speed gears, speed control by turning the handwheel is only permitted during operation! A change in speed while stationary can damage the stepless adjustment unit. All product photos are non-binding examples! Technical changes reserved.

Worm variable speed gear motor, Power= 1.5 kW, Speed= 13.5 - 66.5 rpm, Voltage= 3 x 230/400 V-50 Hz, 3 x 265/460 V-60 Hz (± 5% according to VDE 0530), Protection type= IP55, iso class= F (155°C), Operating mode= S1, Duty cycle= S1- 100%, Total length= approx. 702 mm, Hollow shaft= 35 mm, motor Speed= 4 poles, gear ratio with adjustment unit (i)= 21 - 105 Gear ratio only worm gear (i)= 15, torque= 150 Nm - 277 Nm, operating factor ( f.s.)= 1, terminal box= above (rotatable), weight= 58 kg, color= RAL 5010 (gentian blue), temperature sensor= 3 x PTC thermistor, gear housing = aluminum, ball bearing = SKF, C&U or equivalent, Cooling= axial fan (plastic). For technical reasons, the variable speed worm gear motor should cannot be operated with a frequency converter. The drive corresponds to IEC 60034-30:2008, is suitable for both directions of rotation and is supplied with an oil filling. Open hollow shafts are to be sealed with a cover cap. This can be ordered under the heading "Accessories". In accordance with VDE 0105 and IEC 364, all work on the electric drive may only be carried out by qualified personnel. As usual with variable speed gears, speed control by turning the handwheel is only permitted during operation! A change in speed while stationary can damage the stepless adjustment unit. All product photos are non-binding examples! Technical changes reserved.

Worm variable speed gear motor, Power= 1.5 kW, Speed= 27 - 133 rpm, Voltage= 3 x 230/400 V-50 Hz, 3 x 265/460 V-60 Hz (± 5% according to VDE 0530), Protection type= IP55, iso class= F (155°C), Operating mode= S1, Duty cycle= S1- 100%, Total length= approx. 702 mm, Hollow shaft = 35 mm, motor speed = 4 poles, translation with adjustment unit (i) = 10.5 - 52.5 Transmission only worm gear (i) = 7.5, torque = 77 Nm – 150 Nm, service factor (f.s.)= 1, terminal box= above (rotatable), weight= 58 kg, color= RAL 5010 (gentian blue), temperature sensor= 3 x PTC thermistors, gearbox housing = aluminium, ball bearings = SKF, C&U or equivalent, Cooling= axial fan (plastic). For technical reasons, the variable speed worm gear motor should cannot be operated with a frequency converter. The drive corresponds to IEC 60034-30:2008, is suitable for both directions of rotation and is supplied with an oil filling. Open hollow shafts are to be sealed with a cover cap. This can be ordered under the heading "Accessories". In accordance with VDE 0105 and IEC 364, all work on the electric drive may only be carried out by qualified personnel. As usual with variable speed gears, speed control by turning the handwheel is only permitted during operation! A change in speed while stationary can damage the stepless adjustment unit. All product photos are non-binding examples! Technical changes reserved.

Worm variable speed gear motor, Power= 1.5 kW, Speed= 7 - 33 rpm, Voltage= 3 x 230/400 V-50 Hz, 3 x 265/460 V-60 Hz (± 5% according to VDE 0530), Protection type= IP55, iso class= F (155°C), Operating mode= S1, Duty cycle= S1- 100%, Total length= approx. 702 mm, Hollow shaft = 35 mm, motor speed = 4 poles, translation with adjustment unit (i) = 42 - 210 Transmission only worm gear (i) = 30, torque = 270 Nm - 474 Nm, service factor ( f.s.)= 1, terminal box= above (rotatable), weight= 58 kg, color= RAL 5010 (gentian blue), temperature sensor= 3 x PTC thermistor, gear housing = aluminum, ball bearing = SKF, C&U or equivalent, Cooling= axial fan (plastic). For technical reasons, the variable speed worm gear motor should cannot be operated with a frequency converter. The drive corresponds to IEC 60034-30:2008, is suitable for both directions of rotation and is supplied with an oil filling. Open hollow shafts are to be sealed with a cover cap. This can be ordered under the heading "Accessories". In accordance with VDE 0105 and IEC 364, all work on the electric drive may only be carried out by qualified personnel. As usual with variable speed gears, speed control by turning the handwheel is only permitted during operation! A change in speed while stationary can damage the stepless adjustment unit. All product photos are non-binding examples! Technical changes reserved.

Worm variable speed gear motor, Power= 1.5 kW, Speed= 4 - 20 rpm, Voltage= 3 x 230/400 V-50 Hz, 3 x 265/460 V-60 Hz (± 5% according to VDE 0530), Protection type= IP55, iso class= F (155°C), Operating mode= S1, Duty cycle= S1- 100%, Total length= approx. 702 mm, Hollow shaft = 35 mm, motor speed = 4 poles, translation with adjustment unit (i) = 70 - 350 Transmission only worm gear (i) = 50, torque = 406 Nm - 560 Nm, service factor ( f.s.)= 1, terminal box= above (rotatable), weight= 58 kg, color= RAL 5010 (gentian blue), temperature sensor= 3 x PTC thermistor, gear housing = aluminum, ball bearing = SKF, C&U or equivalent, Cooling= axial fan (plastic). For technical reasons, the variable speed worm gear motor should cannot be operated with a frequency converter. The drive corresponds to IEC 60034-30:2008, is suitable for both directions of rotation and is supplied with an oil filling. Open hollow shafts are to be sealed with a cover cap. This can be ordered under the heading "Accessories". In accordance with VDE 0105 and IEC 364, all work on the electric drive may only be carried out by qualified personnel. As usual with variable speed gears, speed control by turning the hand wheel is only permitted during operation! A change in speed while stationary can damage the stepless adjustment unit. All product photos are non-binding examples! Technical changes reserved.

Worm variable speed gear motor, Power= 1.5 kW, Speed= 20 - 100 rpm, Voltage= 3 x 230/400 V-50 Hz, 3 x 265/460 V-60 Hz (± 5% according to VDE 0530), Protection type= IP55, iso class= F (155°C), Operating mode= S1, Duty cycle= S1- 100%, Total length= approx. 702 mm, Hollow shaft = 35 mm, motor speed = 4 poles, translation with adjustment unit (i) = 14 - 70 Transmission only worm gear (i) = 10, torque = 104 Nm - 195 Nm, service factor ( f.s.)= 1, terminal box= above (rotatable), weight= 58 kg, color= RAL 5010 (gentian blue), temperature sensor= 3 x PTC thermistor, gear housing = aluminum, ball bearing = SKF, C&U or equivalent, Cooling= axial fan (plastic). For technical reasons, the variable speed worm gear motor should cannot be operated with a frequency converter. The drive corresponds to IEC 60034-30:2008, is suitable for both directions of rotation and is supplied with an oil filling. Open hollow shafts are to be sealed with a cover cap. This can be ordered under the heading "Accessories". In accordance with VDE 0105 and IEC 364, all work on the electric drive may only be carried out by qualified personnel. As usual with variable speed gears, speed control by turning the handwheel is only permitted during operation! A change in speed while stationary can damage the stepless adjustment unit. All product photos are non-binding examples! Technical changes reserved.

Worm variable speed gear motor, Power= 1.5 kW, Speed= 8 - 40 rpm, Voltage= 3 x 230/400 V-50 Hz, 3 x 265/460 V-60 Hz (± 5% according to VDE 0530), Protection type= IP55, iso class= F (155°C), Operating mode= S1, Duty cycle= S1- 100%, Total length= approx. 702 mm, Hollow shaft = 35 mm, motor speed = 4 poles, translation with adjustment unit (i) = 35 - 175 Transmission only worm gear (i) = 25, torque = 236 Nm - 427 Nm, service factor ( f.s.)= 1, terminal box= above (rotatable), weight= 58 kg, color= RAL 5010 (gentian blue), temperature sensor= 3 x PTC thermistor, gear housing = aluminum, ball bearing = SKF, C&U or equivalent, Cooling= axial fan (plastic). For technical reasons, the variable speed worm gear motor should cannot be operated with a frequency converter. The drive corresponds to IEC 60034-30:2008, is suitable for both directions of rotation and is supplied with an oil filling. Open hollow shafts are to be sealed with a cover cap. This can be ordered under the heading "Accessories". In accordance with VDE 0105 and IEC 364, all work on the electric drive may only be carried out by qualified personnel. As usual with variable speed gears, speed control by turning the handwheel is only permitted during operation! A change in speed while stationary can damage the stepless adjustment unit. All product photos are non-binding examples! Technical changes reserved.

Worm variable speed gear motor, Power= 1.5 kW, Speed= 10 - 50 rpm, Voltage= 3 x 230/400 V-50 Hz, 3 x 265/460 V-60 Hz (± 5% according to VDE 0530), Protection type= IP55, iso class= F (155°C), Operating mode= S1, Duty cycle= S1- 100%, Total length= approx. 702 mm, Hollow shaft = 35 mm, motor speed = 4 poles, translation with adjustment unit (i) = 28 - 140 Transmission only worm gear (i) = 20, torque = 194 Nm - 355 Nm, service factor ( f.s.)= 1, terminal box= above (rotatable), weight= 58 kg, color= RAL 5010 (gentian blue), temperature sensor= 3 x PTC thermistor, gear housing = aluminum, ball bearing = SKF, C&U or equivalent, Cooling= axial fan (plastic). For technical reasons, the variable speed worm gear motor should cannot be operated with a frequency converter. The drive corresponds to IEC 60034-30:2008, is suitable for both directions of rotation and is supplied with an oil filling. Open hollow shafts are to be sealed with a cover cap. This can be ordered under the heading "Accessories". In accordance with VDE 0105 and IEC 364, all work on the electric drive may only be carried out by qualified personnel. As usual with variable speed gears, speed control by turning the handwheel is only permitted during operation! A change in speed while stationary can damage the stepless adjustment unit. All product photos are non-binding examples! Technical changes reserved.

Worm variable speed gear motor, Power= 1.1 kW, Speed= 2.5 - 12.5 rpm, Voltage= 3 x 230/400 V-50 Hz, 3 x 265/460 V-60 Hz (± 5% according to VDE 0530), Protection type= IP55, iso class= F (155°C), Operating mode= S1, Duty cycle= S1- 100%, Total length= approx. 732 mm, Hollow shaft = 42 mm, motor speed = 4 poles, translation with adjustment unit (i) = 112 - 560 Transmission only worm gear (i) = 80, torque = 455 Nm - 754 Nm, service factor ( f.s.)= 1, terminal box= above (rotatable), weight= 21 kg, color= RAL 5010 (gentian blue), temperature sensor= 3 x PTC thermistor, gear housing = aluminum, ball bearing = SKF, C&U or equivalent, Cooling= axial fan (plastic). For technical reasons, the variable speed worm gear motor should cannot be operated with a frequency converter. The drive corresponds to IEC 60034-30:2008, is suitable for both directions of rotation and is supplied with an oil filling. Open hollow shafts are to be sealed with a cover cap. This can be ordered under the heading "Accessories". In accordance with VDE 0105 and IEC 364, all work on the electric drive may only be carried out by qualified personnel. As usual with variable speed gears, speed control by turning the handwheel is only permitted during operation! A change in speed while stationary can damage the stepless adjustment unit. All product photos are non-binding examples! Technical changes reserved.