Worm variable speed gear motor, Power= 0.37 kW, Speed= 4 - 20 rpm, Voltage= 3 x 230/400 V-50 Hz, 3 x 265/460 V-60 Hz (± 5% according to VDE 0530), Protection type= IP55, iso class= F (155°C), Operating mode= S1, Duty cycle= S1- 100%, Total length= approx. 473 mm, Hollow shaft = 25 mm, motor speed = 4 poles, translation with adjustment unit (i) = 70 - 350 Transmission only worm gear (i) = 50, torque = 89 Nm - 120 Nm, service factor ( f.s.)= 1, terminal box= above (rotatable), weight= 15 kg, color= RAL 5010 (gentian blue), temperature sensor= 3 x PTC thermistor, gear housing = aluminum, ball bearing = SKF, C&U or equivalent, Cooling= axial fan (plastic). For technical reasons, the variable speed worm gear motor should cannot be operated with a frequency converter. The drive corresponds to IEC 60034-30:2008, is suitable for both directions of rotation and is supplied with an oil filling. Open hollow shafts are to be sealed with a cover cap. This can be ordered under the heading "Accessories". According to VDE 0105 and IEC 364, all work on the electric drive may only be carried out by qualified personnel. As usual with variable speed gears, speed control by turning the handwheel is only permitted during operation! A change in speed while stationary can damage the stepless adjustment unit. All product photos are non-binding examples! Technical changes reserved.

Worm variable speed gear motor, Power= 0.37 kW, Speed= 10 - 50 rpm, Voltage= 3 x 230/400 V-50 Hz, 3 x 265/460 V-60 Hz (± 5% according to VDE 0530), Protection type= IP55, iso class= F (155°C), Operating mode= S1, Duty cycle= S1- 100%, Total length= approx. 473 mm, Hollow shaft = 25 mm, motor speed = 4 poles, translation with adjustment unit (i) = 28 - 140 Transmission only worm gear (i) = 20, torque = 46 Nm - 82 Nm, service factor ( f.s.)= 1, terminal box= above (rotatable), weight= 15 kg, color= RAL 5010 (gentian blue), temperature sensor= 3 x PTC thermistor, gear housing = aluminum, ball bearing = SKF, C&U or equivalent, Cooling= axial fan (plastic). For technical reasons, the variable speed worm gear motor should cannot be operated with a frequency converter. The drive corresponds to IEC 60034-30:2008, is suitable for both directions of rotation and is supplied with an oil filling. Open hollow shafts are to be sealed with a cover cap. This can be ordered under the heading "Accessories". According to VDE 0105 and IEC 364, all work on the electric drive may only be carried out by qualified personnel. As usual with variable speed gears, speed control by turning the handwheel is only permitted during operation! A change in speed while stationary can damage the stepless adjustment unit. All product photos are non-binding examples! Technical changes reserved.

Worm variable speed gear motor, Power= 0.37 kW, Speed= 27 - 133 rpm, Voltage= 3 x 230/400 V-50 Hz, 3 x 265/460 V-60 Hz (± 5% according to VDE 0530), Protection type= IP55, iso class= F (155°C), Operating mode= S1, Duty cycle= S1- 100%, Total length= approx. 473 mm, Hollow shaft = 25 mm, motor speed = 4 poles, translation with adjustment unit (i) = 10.5 - 52.5 Transmission only worm gear (i) = 7.5, torque = 19 Nm - 36 Nm, service factor (f.s.)= 1, terminal box= above (rotatable), weight= 15 kg, color= RAL 5010 (gentian blue), temperature sensor= 3 x PTC thermistors, gearbox housing = aluminium, ball bearings = SKF, C&U or equivalent, Cooling= axial fan (plastic). For technical reasons, the variable speed worm gear motor should cannot be operated with a frequency converter. The drive corresponds to IEC 60034-30:2008, is suitable for both directions of rotation and is supplied with an oil filling. Open hollow shafts are to be sealed with a cover cap. This can be ordered under the heading "Accessories". In accordance with VDE 0105 and IEC 364, all work on the electric drive may only be carried out by qualified personnel. As usual with variable speed gears, speed control by turning the handwheel is only permitted during operation! A change in speed while stationary can damage the stepless adjustment unit. All product photos are non-binding examples! Technical changes reserved.

Worm variable speed gear motor, Power= 0.37 kW, Speed= 20 - 100 rpm, Voltage= 3 x 230/400 V-50 Hz, 3 x 265/460 V-60 Hz (± 5% according to VDE 0530), Protection type= IP55, iso class= F (155°C), Operating mode= S1, Duty cycle= S1- 100%, Total length= approx. 473 mm, Hollow shaft= 25 mm, motor Speed= 4 poles, gear ratio with adjustment unit (i)= 14 - 70 Gear ratio only worm gear (i)= 10, torque= 25 Nm - 47 Nm, operating factor ( f.s.)= 1, terminal box= above (rotatable), weight= 15 kg, color= RAL 5010 (gentian blue), temperature sensor= 3 x PTC thermistor, gear housing = aluminum, ball bearing = SKF, C&U or equivalent, Cooling= axial fan (plastic). For technical reasons, the variable speed worm gear motor should cannot be operated with a frequency converter. The drive corresponds to IEC 60034-30:2008, is suitable for both directions of rotation and is supplied with an oil filling. Open hollow shafts are to be sealed with a cover cap. This can be ordered under the heading "Accessories". According to VDE 0105 and IEC 364, all work on the electric drive may only be carried out by qualified personnel. As usual with variable speed gears, speed control by turning the hand wheel is only permitted during operation! A change in speed while stationary can damage the stepless adjustment unit. All product photos are non-binding examples! Technical changes reserved.

Worm variable speed gear motor, Power= 0.37 kW, Speed= 5 - 25 rpm, Voltage= 3 x 230/400 V-50 Hz, 3 x 265/460 V-60 Hz (± 5% according to VDE 0530), Protection type= IP55, iso class= F (155°C), Operating mode= S1, Duty cycle= S1- 100%, Total length= approx. 473 mm, Hollow shaft = 25 mm, motor speed = 4 poles, translation with adjustment unit (i) = 56 - 280 Transmission only worm gear (i) = 40, torque = 76 Nm - 124 Nm, operating factor ( f.s.)= 1, terminal box= above (rotatable), weight= 15 kg, color= RAL 5010 (gentian blue), temperature sensor= 3 x PTC thermistor, gear housing = aluminum, ball bearing = SKF, C&U or equivalent, Cooling= axial fan (plastic). For technical reasons, the variable speed worm gear motor should cannot be operated with a frequency converter. The drive corresponds to IEC 60034-30:2008, is suitable for both directions of rotation and is supplied with an oil filling. Open hollow shafts are to be sealed with a cover cap. This can be ordered under the heading "Accessories". According to VDE 0105 and IEC 364, all work on the electric drive may only be carried out by qualified personnel. As usual with variable speed gears, speed control by turning the handwheel is only permitted during operation! A change in speed while stationary can damage the stepless adjustment unit. All product photos are non-binding examples! Technical changes reserved.

Worm variable speed gear motor, Power= 0.37 kW, Speed= 13.5 - 66.5 rpm, Voltage= 3 x 230/400 V-50 Hz, 3 x 265/460 V-60 Hz (± 5% according to VDE 0530), Protection type= IP55, iso class= F (155°C), Operating mode= S1, Duty cycle= S1- 100%, Total length= approx. 473 mm, Hollow shaft = 25 mm, motor speed = 4 poles, translation with adjustment unit (i) = 21 - 105 Transmission only worm gear (i) = 15, torque = 36 Nm - 65 Nm, operating factor ( f.s.)= 1, terminal box= above (rotatable), weight= 15 kg, color= RAL 5010 (gentian blue), temperature sensor= 3 x PTC thermistor, gear housing = aluminum, ball bearing = SKF, C&U or equivalent, Cooling= axial fan (plastic). For technical reasons, the variable speed worm gear motor should cannot be operated with a frequency converter. The drive corresponds to IEC 60034-30:2008, is suitable for both directions of rotation and is supplied with an oil filling. Open hollow shafts are to be sealed with a cover cap. This can be ordered under the heading "Accessories". According to VDE 0105 and IEC 364, all work on the electric drive may only be carried out by qualified personnel. As usual with variable speed gears, speed control by turning the handwheel is only permitted during operation! A change in speed while stationary can damage the stepless adjustment unit. All product photos are non-binding examples! Technical changes reserved.

Worm variable speed gear motor, Power= 0.37 kW, Speed= 8 - 40 rpm, Voltage= 3 x 230/400 V-50 Hz, 3 x 265/460 V-60 Hz (± 5% according to VDE 0530), Protection type= IP55, iso class= F (155°C), Operating mode= S1, Duty cycle= S1- 100%, Total length= approx. 473 mm, Hollow shaft = 25 mm, motor speed = 4 poles, translation with adjustment unit (i) = 35 - 175 Transmission only worm gear (i) = 25, torque = 55 Nm - 97 Nm, service factor ( f.s.)= 1, terminal box= above (rotatable), weight= 15 kg, color= RAL 5010 (gentian blue), temperature sensor= 3 x PTC thermistor, gear housing = aluminum, ball bearing = SKF, C&U or equivalent, Cooling= axial fan (plastic). For technical reasons, the variable speed worm gear motor should cannot be operated with a frequency converter. The drive corresponds to IEC 60034-30:2008, is suitable for both directions of rotation and is supplied with an oil filling. Open hollow shafts are to be sealed with a cover cap. This can be ordered under the heading "Accessories". According to VDE 0105 and IEC 364, all work on the electric drive may only be carried out by qualified personnel. As usual with variable speed gears, speed control by turning the handwheel is only permitted during operation! A change in speed while stationary can damage the stepless adjustment unit. All product photos are non-binding examples! Technical changes reserved.

Worm variable speed gear motor, Power= 0.25 kW, Speed= 5 - 25 rpm, Voltage= 3 x 230/400 V-50 Hz, 3 x 265/460 V-60 Hz (± 5% according to VDE 0530), Protection type= IP55, iso class= F (155°C), Operating mode= S1, Duty cycle= S1- 100%, Total length= approx. 453 mm, Hollow shaft = 18 mm, Motor speed = 4 poles, Translation with adjustment unit (i) = 56 - 280 Transmission only worm gear (i) = 40, Torque = 48 Nm - 96 Nm, Service factor ( f.s.)= 1, Terminal box= above (rotatable), Weight= 14 kg, Color= RAL 5010 (gentian blue), Temperature sensor= 3 x PTC thermistors, Gear housing = Aluminum, Ball bearing = SKF, C&U or equivalent, Cooling= axial fan (plastic). For technical reasons, the variable speed worm gear motor should cannot be operated with a frequency converter. The drive corresponds to IEC 60034-30:2008, is suitable for both directions of rotation and is supplied with an oil filling. Open hollow shafts are to be sealed with a cover cap. This can be ordered under the heading "Accessories". In accordance with VDE 0105 and IEC 364, all work on the electric drive may only be carried out by qualified personnel. As usual with variable speed gears, speed control by turning the handwheel is only permitted during operation! A change in speed while stationary can damage the stepless adjustment unit. All product photos are non-binding examples! Technical changes reserved.

Worm variable speed gear motor, Power= 0.37 kW, Speed= 5 - 25 rpm, Voltage= 3 x 230/400 V-50 Hz, 3 x 265/460 V-60 Hz (± 5% according to VDE 0530), Protection type= IP55, iso class= F (155°C), Operating mode= S1, Duty cycle= S1- 100%, Total length= approx. 500 mm, Hollow shaft = 25 mm, motor speed = 4 poles, translation with adjustment unit (i) = 56 - 280 Transmission only worm gear (i) = 40, torque = 79 Nm - 134 Nm, operating factor ( f.s.)= 1, terminal box= above (rotatable), weight= 16 kg, color= RAL 5010 (gentian blue), temperature sensor= 3 x PTC thermistors, gear housing = aluminum, ball bearing = SKF, C&U or equivalent, Cooling= axial fan (plastic). For technical reasons, the variable speed worm gear motor should cannot be operated with a frequency converter. The drive corresponds to IEC 60034-30:2008, is suitable for both directions of rotation and is supplied with an oil filling. Open hollow shafts are to be sealed with a cover cap. This can be ordered under the heading "Accessories". According to VDE 0105 and IEC 364, all work on the electric drive may only be carried out by qualified personnel. As usual with variable speed gears, speed control by turning the handwheel is only permitted during operation! A change in speed while stationary can damage the stepless adjustment unit. All product photos are non-binding examples! Technical changes reserved.

Worm variable speed gear motor, Power= 0.37 kW, Speed= 2 - 10 rpm, Voltage= 3 x 230/400 V-50 Hz, 3 x 265/460 V-60 Hz (± 5% according to VDE 0530), Protection type= IP55, iso class= F (155°C), Operating mode= S1, Duty cycle= S1- 100%, Total length= approx. 500 mm, Hollow shaft = 25 mm, motor speed = 4 poles, translation with adjustment unit (i) = 140 - 700 Transmission only worm gear (i) = 100, torque = 139 Nm - 150 Nm, service factor ( f.s.)= 1, terminal box= above (rotatable), weight= 16 kg, color= RAL 5010 (gentian blue), temperature sensor= 3 x PTC thermistor, gear housing = aluminum, ball bearing = SKF, C&U or equivalent, Cooling= axial fan (plastic). For technical reasons, the variable speed worm gear motor should cannot be operated with a frequency converter. The drive corresponds to IEC 60034-30:2008, is suitable for both directions of rotation and is supplied with an oil filling. Open hollow shafts are to be sealed with a cover cap. This can be ordered under the heading "Accessories". According to VDE 0105 and IEC 364, all work on the electric drive may only be carried out by qualified personnel. As usual with variable speed gears, speed control by turning the hand wheel is only permitted during operation! A change in speed while stationary can damage the stepless adjustment unit. All product photos are non-binding examples! Technical changes reserved.

Worm variable speed gear motor, Power= 0.37 kW, Speed= 4 - 20 rpm, Voltage= 3 x 230/400 V-50 Hz, 3 x 265/460 V-60 Hz (± 5% according to VDE 0530), Protection type= IP55, iso class= F (155°C), Operating mode= S1, Duty cycle= S1- 100%, Total length= approx. 500 mm, Hollow shaft = 25 mm, motor speed = 4 poles, translation with adjustment unit (i) = 70 - 350 Transmission only worm gear (i) = 50, torque = 92 Nm - 155 Nm, operating factor ( f.s.)= 1, terminal box= above (rotatable), weight= 16 kg, color= RAL 5010 (gentian blue), temperature sensor= 3 x PTC thermistors, gear housing = aluminum, ball bearing = SKF, C&U or equivalent, Cooling= axial fan (plastic). For technical reasons, the variable speed worm gear motor should cannot be operated with a frequency converter. The drive corresponds to IEC 60034-30:2008, is suitable for both directions of rotation and is supplied with an oil filling. Open hollow shafts are to be sealed with a cover cap. This can be ordered under the heading "Accessories". According to VDE 0105 and IEC 364, all work on the electric drive may only be carried out by qualified personnel. As usual with variable speed gears, speed control by turning the handwheel is only permitted during operation! A change in speed while stationary can damage the stepless adjustment unit. All product photos are non-binding examples! Technical changes reserved.

Worm variable speed gear motor, Power= 0.37 kW, Speed= 3.5 - 16.5 rpm, Voltage= 3 x 230/400 V-50 Hz, 3 x 265/460 V-60 Hz (± 5% according to VDE 0530), Protection type= IP55, iso class= F (155°C), Operating mode= S1, Duty cycle= S1- 100%, Total length= approx. 500 mm, Hollow shaft = 25 mm, motor speed = 4 poles, translation with adjustment unit (i) = 84 - 420 Transmission only worm gear (i) = 60, torque = 104 Nm - 173 Nm, service factor ( f.s.)= 1, terminal box= above (rotatable), weight= 16 kg, color= RAL 5010 (gentian blue), temperature sensor= 3 x PTC thermistors, gear housing = aluminum, ball bearing = SKF, C&U or equivalent, Cooling= axial fan (plastic). For technical reasons, the variable speed worm gear motor should cannot be operated with a frequency converter. The drive corresponds to IEC 60034-30:2008, is suitable for both directions of rotation and is supplied with an oil filling. Open hollow shafts are to be sealed with a cover cap. This can be ordered under the heading "Accessories". According to VDE 0105 and IEC 364, all work on the electric drive may only be carried out by qualified personnel. As usual with variable speed gears, speed control by turning the handwheel is only permitted during operation! A change in speed while stationary can damage the stepless adjustment unit. All product photos are non-binding examples! Technical changes reserved.

Worm variable speed gear motor, Power= 0.37 kW, Speed= 2.5 - 12.5 rpm, Voltage= 3 x 230/400 V-50 Hz, 3 x 265/460 V-60 Hz (± 5% according to VDE 0530), Protection type= IP55, iso class= F (155°C), Operating mode= S1, Duty cycle= S1- 100%, Total length= approx. 500 mm, Hollow shaft = 25 mm, motor speed = 4 poles, translation with adjustment unit (i) = 112 - 560 Transmission only worm gear (i) = 80, torque = 125 Nm - 173 Nm, operating factor ( f.s.)= 1, terminal box= above (rotatable), weight= 16 kg, color= RAL 5010 (gentian blue), temperature sensor= 3 x PTC thermistors, gear housing = aluminum, ball bearing = SKF, C&U or equivalent, Cooling= axial fan (plastic). For technical reasons, the variable speed worm gear motor should cannot be operated with a frequency converter. The drive corresponds to IEC 60034-30:2008, is suitable for both directions of rotation and is supplied with an oil filling. Open hollow shafts are to be sealed with a cover cap. This can be ordered under the heading "Accessories". According to VDE 0105 and IEC 364, all work on the electric drive may only be carried out by qualified personnel. As usual with variable speed gears, speed control by turning the handwheel is only permitted during operation! A change in speed while stationary can damage the stepless adjustment unit. All product photos are non-binding examples! Technical changes reserved.

Worm variable speed gear motor, Power= 0.75 kW, Speed= 34 - 200 rpm, Voltage= 3 x 230/400 V-50 Hz, 3 x 265/460 V-60 Hz (± 5% according to VDE 0530), Protection type= IP55, iso class= F (155°C), Operating mode= S1, Duty cycle= S1- 100%, Total length= approx. 473 mm, Hollow shaft = 25 mm, motor speed = 2 poles, translation with adjustment unit (i) = 14 - 70 Transmission only worm gear (i) = 10, torque = 25.8 Nm - 48.6 Nm, service factor (f.s.)= 3.3, terminal box= above (rotatable), weight= 18 kg, color= RAL 5010 (gentian blue), temperature sensor= 3 x PTC thermistors, gearbox housing = aluminium, ball bearings = SKF, C&U or equivalent, Cooling= axial fan (plastic). For technical reasons, the variable speed worm gear motor should cannot be operated with a frequency converter. The drive corresponds to IEC 60034-30:2008, is suitable for both directions of rotation and is supplied with an oil filling. Open hollow shafts are to be sealed with a cover cap. This can be ordered under the heading "Accessories". In accordance with VDE 0105 and IEC 364, all work on the electric drive may only be carried out by qualified personnel. As usual with variable speed gears, speed control by turning the handwheel is only permitted during operation! A change in speed while stationary can damage the stepless adjustment unit. All product photos are non-binding examples! Technical changes reserved.

Worm variable speed gear motor, Power= 0.55 kW, Speed= 10 - 50 rpm, Voltage= 3 x 230/400 V-50 Hz, 3 x 265/460 V-60 Hz (± 5% according to VDE 0530), Protection type= IP55, iso class= F (155°C), Operating mode= S1, Duty cycle= S1- 100%, Total length= approx. 566 mm, Hollow shaft = 25 mm, motor speed = 4 poles, translation with adjustment unit (i) = 28 - 140 Transmission only worm gear (i) = 20, torque = 62 Nm - 112 Nm, service factor ( f.s.)= 1, terminal box= above (rotatable), weight= 17 kg, color= RAL 5010 (gentian blue), temperature sensor= 3 x PTC thermistors, gear housing = aluminum, ball bearing = SKF, C&U or equivalent, Cooling= axial fan (plastic). For technical reasons, the variable speed worm gear motor should cannot be operated with a frequency converter. The drive corresponds to IEC 60034-30:2008, is suitable for both directions of rotation and is supplied with an oil filling. Open hollow shafts are to be sealed with a cover cap. This can be ordered under the heading "Accessories". According to VDE 0105 and IEC 364, all work on the electric drive may only be carried out by qualified personnel. As usual with variable speed gears, speed control by turning the handwheel is only permitted during operation! A change in speed while stationary can damage the stepless adjustment unit. All product photos are non-binding examples! Technical changes reserved.

Worm variable speed gear motor, Power= 0.55 kW, Speed= 5 - 25 rpm, Voltage= 3 x 230/400 V-50 Hz, 3 x 265/460 V-60 Hz (± 5% according to VDE 0530), Protection type= IP55, iso class= F (155°C), Operating mode= S1, Duty cycle= S1- 100%, Total length= approx. 566 mm, Hollow shaft = 25 mm, motor speed = 4 poles, translation with adjustment unit (i) = 56 - 280 Transmission only worm gear (i) = 40, torque = 105 Nm - 179 Nm, operating factor ( f.s.)= 1, terminal box= above (rotatable), weight= 17 kg, color= RAL 5010 (gentian blue), temperature sensor= 3 x PTC thermistors, gear housing = aluminum, ball bearing = SKF, C&U or equivalent, Cooling= axial fan (plastic). For technical reasons, the variable speed worm gear motor should cannot be operated with a frequency converter. The drive corresponds to IEC 60034-30:2008, is suitable for both directions of rotation and is supplied with an oil filling. Open hollow shafts are to be sealed with a cover cap. This can be ordered under the heading "Accessories". According to VDE 0105 and IEC 364, all work on the electric drive may only be carried out by qualified personnel. As usual with variable speed gears, speed control by turning the handwheel is only permitted during operation! A change in speed while stationary can damage the stepless adjustment unit. All product photos are non-binding examples! Technical changes reserved.

Worm variable speed gear motor, Power= 0.55 kW, Speed= 13.5 - 66.5 rpm, Voltage= 3 x 230/400 V-50 Hz, 3 x 265/460 V-60 Hz (± 5% according to VDE 0530), Protection type= IP55, iso class= F (155°C), Operating mode= S1, Duty cycle= S1- 100%, Total length= approx. 566 mm, Hollow shaft = 25 mm, motor speed = 4 poles, translation with adjustment unit (i) = 21 - 105 Transmission only worm gear (i) = 15, torque = 48 Nm - 88 Nm, service factor ( f.s.)= 1, terminal box= above (rotatable), weight= 17 kg, color= RAL 5010 (gentian blue), temperature sensor= 3 x PTC thermistors, gear housing = aluminum, ball bearing = SKF, C&U or equivalent, Cooling= axial fan (plastic). For technical reasons, the variable speed worm gear motor should cannot be operated with a frequency converter. The drive corresponds to IEC 60034-30:2008, is suitable for both directions of rotation and is supplied with an oil filling. Open hollow shafts are to be sealed with a cover cap. This can be ordered under the heading "Accessories". According to VDE 0105 and IEC 364, all work on the electric drive may only be carried out by qualified personnel. As usual with variable speed gears, speed control by turning the handwheel is only permitted during operation! A change in speed while stationary can damage the stepless adjustment unit. All product photos are non-binding examples! Technical changes reserved.

Worm variable speed gear motor, Power= 0.55 kW, Speed= 7 - 33 rpm, Voltage= 3 x 230/400 V-50 Hz, 3 x 265/460 V-60 Hz (± 5% according to VDE 0530), Protection type= IP55, iso class= F (155°C), Operating mode= S1, Duty cycle= S1- 100%, Total length= approx. 566 mm, Hollow shaft = 25 mm, motor speed = 4 poles, translation with adjustment unit (i) = 42 - 210 Transmission only worm gear (i) = 30, torque = 81 Nm - 146 Nm, service factor ( f.s.)= 1, terminal box= above (rotatable), weight= 17 kg, color= RAL 5010 (gentian blue), temperature sensor= 3 x PTC thermistors, gear housing = aluminum, ball bearing = SKF, C&U or equivalent, Cooling= axial fan (plastic). For technical reasons, the variable speed worm gear motor should cannot be operated with a frequency converter. The drive corresponds to IEC 60034-30:2008, is suitable for both directions of rotation and is supplied with an oil filling. Open hollow shafts are to be sealed with a cover cap. This can be ordered under the heading "Accessories". According to VDE 0105 and IEC 364, all work on the electric drive may only be carried out by qualified personnel. As usual with variable speed gears, speed control by turning the hand wheel is only permitted during operation! A change in speed while stationary can damage the stepless adjustment unit. All product photos are non-binding examples! Technical changes reserved.

Worm variable speed gear motor, Power= 0.55 kW, Speed= 8 - 40 rpm, Voltage= 3 x 230/400 V-50 Hz, 3 x 265/460 V-60 Hz (± 5% according to VDE 0530), Protection type= IP55, iso class= F (155°C), Operating mode= S1, Duty cycle= S1- 100%, Total length= approx. 566 mm, Hollow shaft = 25 mm, motor speed = 4 poles, translation with adjustment unit (i) = 35 - 175 Transmission only worm gear (i) = 25, torque = 75 Nm - 133 Nm, operating factor ( f.s.)= 1, terminal box= above (rotatable), weight= 17 kg, color= RAL 5010 (gentian blue), temperature sensor= 3 x PTC thermistors, gear housing = aluminum, ball bearing = SKF, C&U or equivalent, Cooling= axial fan (plastic). For technical reasons, the variable speed worm gear motor should cannot be operated with a frequency converter. The drive corresponds to IEC 60034-30:2008, is suitable for both directions of rotation and is supplied with an oil filling. Open hollow shafts are to be sealed with a cover cap. This can be ordered under the heading "Accessories". According to VDE 0105 and IEC 364, all work on the electric drive may only be carried out by qualified personnel. As usual with variable speed gears, speed control by turning the handwheel is only permitted during operation! A change in speed while stationary can damage the stepless adjustment unit. All product photos are non-binding examples! Technical changes reserved.

Worm variable speed gear motor, Power= 0.55 kW, Speed= 20 - 100 rpm, Voltage= 3 x 230/400 V-50 Hz, 3 x 265/460 V-60 Hz (± 5% according to VDE 0530), Protection type= IP55, iso class= F (155°C), Operating mode= S1, Duty cycle= S1- 100%, Total length= approx. 566 mm, Hollow shaft = 25 mm, motor speed = 4 poles, translation with adjustment unit (i) = 14 - 70 Transmission only worm gear (i) = 10, torque = 34 Nm - 63 Nm, service factor ( f.s.)= 1, terminal box= above (rotatable), weight= 17 kg, color= RAL 5010 (gentian blue), temperature sensor= 3 x PTC thermistors, gear housing = aluminum, ball bearing = SKF, C&U or equivalent, Cooling= axial fan (plastic). For technical reasons, the variable speed worm gear motor should cannot be operated with a frequency converter. The drive corresponds to IEC 60034-30:2008, is suitable for both directions of rotation and is supplied with an oil filling. Open hollow shafts are to be sealed with a cover cap. This can be ordered under the heading "Accessories". According to VDE 0105 and IEC 364, all work on the electric drive may only be carried out by qualified personnel. As usual with variable speed gears, speed control by turning the handwheel is only permitted during operation! A change in speed while stationary can damage the stepless adjustment unit. All product photos are non-binding examples! Technical changes reserved.

Worm variable speed gear motor, Power= 0.55 kW, Speed= 4 - 20 rpm, Voltage= 3 x 230/400 V-50 Hz, 3 x 265/460 V-60 Hz (± 5% according to VDE 0530), Protection type= IP55, iso class= F (155°C), Operating mode= S1, Duty cycle= S1- 100%, Total length= approx. 566 mm, Hollow shaft = 25 mm, motor speed = 4 poles, translation with adjustment unit (i) = 70 - 350 Transmission only worm gear (i) = 50, torque = 123 Nm - 207 Nm, operating factor ( f.s.)= 1, terminal box= above (rotatable), weight= 17 kg, color= RAL 5010 (gentian blue), temperature sensor= 3 x PTC thermistors, gear housing = aluminum, ball bearing = SKF, C&U or equivalent, Cooling= axial fan (plastic). For technical reasons, the variable speed worm gear motor should cannot be operated with a frequency converter. The drive corresponds to IEC 60034-30:2008, is suitable for both directions of rotation and is supplied with an oil filling. Open hollow shafts are to be sealed with a cover cap. This can be ordered under the heading "Accessories". According to VDE 0105 and IEC 364, all work on the electric drive may only be carried out by qualified personnel. As usual with variable speed gears, speed control by turning the handwheel is only permitted during operation! A change in speed while stationary can damage the stepless adjustment unit. All product photos are non-binding examples! Technical changes reserved.

Worm variable speed gear motor, Power= 0.55 kW, Speed= 27 - 133 rpm, Voltage= 3 x 230/400 V-50 Hz, 3 x 265/460 V-60 Hz (± 5% according to VDE 0530), Protection type= IP55, iso class= F (155°C), Operating mode= S1, Duty cycle= S1- 100%, Total length= approx. 566 mm, Hollow shaft = 25 mm, motor speed = 4 poles, translation with adjustment unit (i) = 10.5 - 52.5 Transmission only worm gear (i) = 7.5, torque = 26 Nm – 49 Nm, service factor (f.s.)= 1, terminal box= above (rotatable), weight= 17 kg, color= RAL 5010 (gentian blue), temperature sensor= 3 x PTC thermistors, gearbox housing = aluminium, ball bearings = SKF, C&U or equivalent, Cooling= axial fan (plastic). For technical reasons, the variable speed worm gear motor should cannot be operated with a frequency converter. The drive corresponds to IEC 60034-30:2008, is suitable for both directions of rotation and is supplied with an oil filling. Open hollow shafts are to be sealed with a cover cap. This can be ordered under the heading "Accessories". According to VDE 0105 and IEC 364, all work on the electric drive may only be carried out by qualified personnel. As usual with variable speed gears, speed control by turning the handwheel is only permitted during operation! A change in speed while stationary can damage the stepless adjustment unit. All product photos are non-binding examples! Technical changes reserved.

Worm variable speed gear motor, Power= 0.75 kW, Speed= 13.5 - 66.5 rpm, Voltage= 3 x 230/400 V-50 Hz, 3 x 265/460 V-60 Hz (± 5% according to VDE 0530), Protection type= IP55, iso class= F (155°C), Operating mode= S1, Duty cycle= S1- 100%, Total length= approx. 566 mm, Hollow shaft= 25 mm, motor Speed= 4 poles, gear ratio with adjustment unit (i)= 21 - 105 Gear ratio only worm gear (i)= 15, torque= 72 Nm - 13273 Nm, operating factor ( f.s.)= 1, terminal box= above (rotatable), weight= 18 kg, color= RAL 5010 (gentian blue), temperature sensor= 3 x PTC thermistors, gear housing = aluminum, ball bearing = SKF, C&U or equivalent, Cooling= axial fan (plastic). For technical reasons, the variable speed worm gear motor should cannot be operated with a frequency converter. The drive corresponds to IEC 60034-30:2008, is suitable for both directions of rotation and is supplied with an oil filling. Open hollow shafts are to be sealed with a cover cap. This can be ordered under the heading "Accessories". According to VDE 0105 and IEC 364, all work on the electric drive may only be carried out by qualified personnel. As usual with variable speed gears, speed control by turning the handwheel is only permitted during operation! A change in speed while stationary can damage the stepless adjustment unit. All product photos are non-binding examples! Technical changes reserved.

Worm variable speed gear motor, Power= 0.75 kW, Speed= 8 - 40 rpm, Voltage= 3 x 230/400 V-50 Hz, 3 x 265/460 V-60 Hz (± 5% according to VDE 0530), Protection type= IP55, iso class= F (155°C), Operating mode= S1, Duty cycle= S1- 100%, Total length= approx. 566 mm, Hollow shaft= 25 mm, motor Speed= 4 poles, gear ratio with adjustment unit (i)= 35 - 175 Gear ratio only worm gear (i)= 25, torque= 112 Nm - 199 Nm, service factor ( f.s.)= 1, terminal box= above (rotatable), weight= 18 kg, color= RAL 5010 (gentian blue), temperature sensor= 3 x PTC thermistors, gear housing = aluminum, ball bearing = SKF, C&U or equivalent, Cooling= axial fan (plastic). For technical reasons, the variable speed worm gear motor should cannot be operated with a frequency converter. The drive corresponds to IEC 60034-30:2008, is suitable for both directions of rotation and is supplied with an oil filling. Open hollow shafts are to be sealed with a cover cap. This can be ordered under the heading "Accessories". According to VDE 0105 and IEC 364, all work on the electric drive may only be carried out by qualified personnel. As usual with variable speed gears, speed control by turning the handwheel is only permitted during operation! A change in speed while stationary can damage the stepless adjustment unit. All product photos are non-binding examples! Technical changes reserved.